What is the vertex?

Пікірлер: 338

  • @hagenohea
    @hagenoheaАй бұрын

    Simple solution: run the drill press down til it bottoms out in the vee< then put your dowel in and drill.

  • @fxm5715

    @fxm5715

    Ай бұрын

    That does assume the v-block is precise, making it a second order calibration. That block looks far from precision to me. :)

  • @1nsanewayn3

    @1nsanewayn3

    Ай бұрын

    NAH.. THIS TOOL IS MUCH MORE SIMPLE & PRECISE.

  • @TheElgutiedu

    @TheElgutiedu

    Ай бұрын

    Con esa solución no podría ser un vídeo que aquí lo importante es hacer un vídeo no sé si sirve para algo la herramienta

  • @akosyoutub

    @akosyoutub

    Ай бұрын

    @@fxm5715 That does assume the JIG is precise... If you can make this pendulum JIG precise enough, then you can probably make the V cutout also precise, e.g. by angling a table saw, and it's much easier too.

  • @fxm5715

    @fxm5715

    Ай бұрын

    @@akosyoutub Certainly, a precise v-block would be optimal in this situation, but you may not always even be holding in a v-block, such as when using an indexing head or a collet block, or just stuck in a drill vice. Yes, there are more precise ways to center find, like dialing it in with and edge finder, etc., but this tool is specifically a fast, good enough option for many things. Not for everything, not for high precision, but handy to have in the toolbox.

  • @WeThePeoplewineoneone
    @WeThePeoplewineoneoneАй бұрын

    Can't find the middle but then finds the middle while making a contraption 😂😂

  • @frontiervirtcharter

    @frontiervirtcharter

    Ай бұрын

    Maybe he has to drill the hole in a hundred of those dowels.. Also it's a lot easier to find the center on a flat surface than a curved one

  • @1nsanewayn3

    @1nsanewayn3

    Ай бұрын

    THEN YOU DON'T UNDERSTAND ABOUT GEOMETRY

  • @jrkbgk1111

    @jrkbgk1111

    Ай бұрын

    That's the first thing I thought too, they do that shit for engagement though, so we're literally giving them what they want by saying anything about it 🙄🤷🏽

  • @lennyf1957

    @lennyf1957

    Ай бұрын

    @@frontiervirtcharter if you have the drill hundreds, you sure as hell need to find a better way than that stupid contraption.

  • @deepakkhandekar007

    @deepakkhandekar007

    Ай бұрын

    This is the comment I was looking for 👌👌👌👌👌😂😂😂😂

  • @capndye91
    @capndye9125 күн бұрын

    Just fucking lower the bit until it just scrapes the top of your work piece. Boom. Youve got center.

  • @twoalward9166

    @twoalward9166

    3 күн бұрын

    It might be close, but it's not certain to be precise.

  • @prettynoose8497
    @prettynoose8497Ай бұрын

    Harbor Freight sells a measurement tool like this for 77 cents

  • @twoalward9166

    @twoalward9166

    3 күн бұрын

    I wonder what people like you will do when you can't "just buy it".

  • @AlanTheBeast100
    @AlanTheBeast100Ай бұрын

    Overkill. Use the vee block to locate centre. Put the dowel in. Go to town.

  • @lourias

    @lourias

    28 күн бұрын

    Okay, your tip makes sense. Another person trid saying the same thing, but forgot to use proper punctuation. Thank you for clarifying.

  • @DanielPerez-dl2gs
    @DanielPerez-dl2gs27 күн бұрын

    What??? That's a whole different project. All you need is to find the tallest part of the wood.

  • @brw3079
    @brw3079Ай бұрын

    Just balance a 6 inch (15 cm) ruler on top, pull the drill bit down till it's touching, move the dowel back and forth until the ruler is horizontal.

  • @trentonterrill9343

    @trentonterrill9343

    Ай бұрын

    Exactly! Even that rectangular piece of plastic could have found center.

  • @markfiges999

    @markfiges999

    Ай бұрын

    That's as close to f'k it is to swearing

  • @user-vl9mh8dv1l
    @user-vl9mh8dv1lАй бұрын

    Это всё делаться гораздо проще, и не надо мудрить

  • @royerk3471
    @royerk3471Ай бұрын

    So now You are ready to drill your hole. So you need to remove the center, Finder, and. to do that you need to remove the dowel so you can take it off the drillbit then you don’t have the center anymore

  • @N.California
    @N.CaliforniaАй бұрын

    The middle is wherever he drills unaided. Once the hole is drilled, roll the cylinder until the hole is top dead center, and viola, it's the middle.

  • @viplavanand5077
    @viplavanand5077Ай бұрын

    This is how a simple thing can be made complicated

  • @user-yb5uz6tu2v
    @user-yb5uz6tu2vАй бұрын

    Это дешевая азиатская подделка на центроискатель от Евгения Чернеги.

  • @Andrewlang90
    @Andrewlang90Ай бұрын

    Guys…..edge finders aren’t expensive

  • @fxm5715

    @fxm5715

    Ай бұрын

    If you think it’s about the cost, you are missing the point.

  • @user-rf3bs7ev2y

    @user-rf3bs7ev2y

    Ай бұрын

    @@fxm5715 yep we are missing the point when useless work needed

  • @fxm5715

    @fxm5715

    Ай бұрын

    @@user-rf3bs7ev2y You merelly express my point with different words.

  • @1nsanewayn3

    @1nsanewayn3

    Ай бұрын

    IF YOU HAVE BRAIN, SKILL AND ALL THOSE STUFF.. WHY WOULD YOU BOTHER YOURSELF GOING SOMEWHERE TO BUY IT? 😅 WHEN YOU DO 'HACK' IT'S NOT ALWAYS ABOUT BEING CHEAPER OR EASIER.

  • @1nsanewayn3

    @1nsanewayn3

    Ай бұрын

    ​@@user-rf3bs7ev2yTHE POINT IS.. YOU'RE ONLY KEYBOARD WARRIOR.. NOT A HANDYMAN.😅 HOW COULD IT BE USELESS WHEN IT'S USEFUL?😂 VERY EASY TO MAKE THO..😂

  • @timapple6586
    @timapple658628 күн бұрын

    A $10 drill block does all this in a split second. Reinventing the square wheel.

  • @marcelma
    @marcelmaАй бұрын

    Yea, in order to find the center of a pole you first buy a whole workshop. Absolutely commendable solution!

  • @wayneberry3453

    @wayneberry3453

    Ай бұрын

    Uh, a drill press and a sander?

  • @wildguardian

    @wildguardian

    Ай бұрын

    "whole workshop"...

  • @zongihangi11
    @zongihangi1128 күн бұрын

    If you think that's accurate, you're sorely mistaken. There is no guarantee that you have drawn the red line exactly as you should. The smaller a shape is, the less precisely it is possible to connect the desired corners. And here it is quite small. It's a good idea in theory, but it's imprecise in practice.

  • @beryllium1932
    @beryllium193211 күн бұрын

    Starfleet insignia "...Woodworking, the final frontier..."

  • @ASANTILLANLI
    @ASANTILLANLIАй бұрын

    Si tienes esa base de madera en la que apoyaras el elemento a perforar, allí puedes centrar el taladro; retiras la pieza, bajas el Chuck y centras con el canal, aseguras la mesa, subes el chuck, colocas la pieza y taladras.

  • @FearsomeWarrior
    @FearsomeWarrior25 күн бұрын

    Drop bit down into the v-block. Done.

  • @jefferyshall
    @jefferyshallАй бұрын

    Rube Goldberg would be proud!

  • @twoalward9166
    @twoalward91663 күн бұрын

    You did a great job. Thanks for the video

  • @ghostgustav2486
    @ghostgustav2486Ай бұрын

    Nice tool, but easier with ruler

  • @Mimer6
    @Mimer65 күн бұрын

    Lots of questionable solutions on the internet but this one actually seems to be very good, because just get it in the exact center and done once it can be reused as many times as you like.

  • @tonydavies3511
    @tonydavies351114 күн бұрын

    Tools I'll never make for a job I'll never do.

  • @trondwell13
    @trondwell1322 күн бұрын

    Half an hour later - just balance the first bit of plastic on the tube and bring down the drill. It’s central when the plastic is level

  • @stingray7275
    @stingray727526 күн бұрын

    und beim umspannen auf Bohrer verstellt sich wieder alles

  • @KronicDaydreamZ
    @KronicDaydreamZАй бұрын

    Ugh i could never work with wood all day. Gives me the chills to this day

  • @salterclan
    @salterclan5 күн бұрын

    Wow. So complicated. Put the small piece of plastic on top of the round item. Let the drill bit hold it. Move it back and forth and when level you found the middle. Just saved a ton of time.

  • @zakariakhamees
    @zakariakhameesАй бұрын

    Just mark a point at its center using a square while the bottom end is parallel to the table.

  • @greatnew_products7436
    @greatnew_products743624 күн бұрын

    So HOW do you center the first hole on the wood?

  • @johnhess351
    @johnhess351Ай бұрын

    Fascinating practical application of geometry. I need to find a vertex about twice per lifetime in my wood working, so a gauge like this would really come in handy when I am reincarnated. I do like it and would be satisfied just making the tool, and then would have to find some circle vertex intensive projects. I especially like the red scribed indicator, nut my 8th grade industrial arts shop teacher would have yelled at you for shaping the parts on the belt sander.

  • @maxscholle8932
    @maxscholle8932Ай бұрын

    The same v block that holds the dowel also locates the center.

  • @kanegami4176
    @kanegami4176Ай бұрын

    congrats you invented the compass

  • @joebledsoe257
    @joebledsoe257Ай бұрын

    Use a strip of paper. When the bit drags it, its on center.

  • @DENTNT
    @DENTNTАй бұрын

    надеюсь это стеб... рукожопости такого уровня не бывает, что бы не найти центр цилиндра

  • @RickR.7777
    @RickR.7777Ай бұрын

    Great Centering Tool Idea! 😊

  • @johncabaniss1628
    @johncabaniss1628Ай бұрын

    I like this , great idea

  • @MrShwaggins
    @MrShwagginsАй бұрын

    Or just buy a cheap indicator, or even sweep the round piece back and forth under the drill, lowering it until it hits.

  • @briankissel7661
    @briankissel7661Күн бұрын

    This is called the Star Trek method.

  • @fxm5715
    @fxm5715Ай бұрын

    Nice tool; thanks for sharing it. I think you might mean apex instead of vertex.

  • @user-nu1ty6ht2y
    @user-nu1ty6ht2yАй бұрын

    A very nice job.

  • @davidwalker4654
    @davidwalker4654Ай бұрын

    Everybody's so creative

  • @mtoronyi
    @mtoronyiАй бұрын

    Another overly complicated solution for a simple problem. Bravo.

  • @xl000
    @xl00023 күн бұрын

    There is no way that this jig that was eyeballed is giving you better results than eyeballing the location of the hole. At least, if the jig itself was 3d printed or something......

  • @MechanicsHome
    @MechanicsHome21 күн бұрын

    So great

  • @paulocezargomes5590
    @paulocezargomes5590Ай бұрын

    Desde que todos tenham esse recurso de ferramentas, muito bom! Mas se não tiver melhor marcar o centro mesmo e furar pela marca

  • @melliW1
    @melliW1Ай бұрын

    FANTASTIC 👍🏻💯

  • @mtnphot
    @mtnphotАй бұрын

    It's far easier than that. Use a thin piece of metal like a feeler gauge between the bit and the workpiece. Move it beck and forth. Whrn it is horizontal you are over the centre.

  • @TalRohan
    @TalRohanАй бұрын

    or if your vee block is accurate line the drill bit up with the bottom of the Vee then put the stock in......

  • @antonionunes4369
    @antonionunes4369Ай бұрын

    Look at the engineering the guy did, to make a simple hole centered in a piece of wood.

  • @rihotamm6196
    @rihotamm6196Ай бұрын

    Surely something more complicated could be invented! Please continue!

  • @mironov234
    @mironov2346 күн бұрын

    кондуктор для сверления в помощь - гораздо быстрее и удобнее

  • @Dreamsoarer
    @DreamsoarerАй бұрын

    Пока делал приспособу для идеального сверления, идеально сделал несколько сверлений без нее

  • @rayal8259
    @rayal8259Ай бұрын

    you could always buy it flange wizard center $10

  • @jamesromboldsr1852
    @jamesromboldsr1852Ай бұрын

    Good idea thank you

  • @domloy1723
    @domloy1723Ай бұрын

    Clever idea

  • @jethropebs
    @jethropebsАй бұрын

    Brilliant.

  • @58DamagedGoods
    @58DamagedGoodsАй бұрын

    Seems like a lot of work for drilling one hole. If mass produced, maybe. But there are multiple easier ways in mass production.

  • @arancibia2006
    @arancibia2006Ай бұрын

    🫨🫨🫨🫨🫨🫨🫨🫨🫨🫨 Convertista la mejor idea del mundo en la mejor herramienta del mundo!! Yo la compraría así tal cual, ni siquiera la copiarla en casa, te la contraria directamente!

  • @theboywholived2
    @theboywholived2Ай бұрын

    So how did you know where the centre was for the wood you drilled for your first hole in the top of that wood, if you hadn't made that tool yet? Is this a chicken and the egg thing?

  • @HentaizerZ
    @HentaizerZАй бұрын

    Будешь вставлять, вынимать сверло и эту приспособу, все настройки улетят.

  • @NamedNitrogen
    @NamedNitrogenАй бұрын

    Ah yes, let me just fetch the clear perspex and belt sander I have laying around

  • @bigmanbpv
    @bigmanbpvАй бұрын

    А не проще ли отцентрировать угловой упор, опустив до конца сверло, а потом установить заготовку?

  • @joecacurak5404
    @joecacurak5404Ай бұрын

    Got a mechanics square that has the device to do that.Can also do many other things.😮

  • @Kolikondriu
    @KolikondriuАй бұрын

    Bien para el centro horizontal, pero no indica el vertical…

  • @JupiterDjembe
    @JupiterDjembeАй бұрын

    If only I had all day to drill one perfect hole

  • @grumpyone5963
    @grumpyone5963Ай бұрын

    Now you have to remove the jig and put a drill bit in the chuck without knocking the workpiece!😢

  • @MichaPawelec-tz4ub
    @MichaPawelec-tz4ubАй бұрын

    So how exactly are you going to drill the hole now?

  • @pietroferrari3420
    @pietroferrari3420Ай бұрын

    Niente è assolutamente perfetto la vera perfezione Consiste nel dare il giusto grado di fallibilità ha un sistema

  • @bogman7474711
    @bogman747471118 сағат бұрын

    Too simple, the drill block has the centre already, line the drill to the block

  • @davidryan7565
    @davidryan7565Ай бұрын

    Get a lazer Pointer, put it level now you got a dot wow that would work

  • @R0T0RGUST
    @R0T0RGUSTАй бұрын

    Use a compass

  • @RylanStorm
    @RylanStormАй бұрын

    You can tell it's going to be unnecessarily complicated when he pulls out the glass.

  • @chipburns4123
    @chipburns4123Ай бұрын

    Not looking for the vertex. Its the tangent you are seeking😂

  • @JT--XL365
    @JT--XL365Ай бұрын

    lol that much easier ways than that to find center on a piece of round stock

  • @xdeadwrongxdeadwrong7181
    @xdeadwrongxdeadwrong7181Ай бұрын

    Nice! 😊

  • @dougjstl1
    @dougjstl1Ай бұрын

    I think you can make that no one piece you don't need two pieces. Is there a advantage of using two pieces and gluing them together.

  • @chrismechanic2000
    @chrismechanic2000Ай бұрын

    you have everything there to find the center already.

  • @Saharok7777
    @Saharok7777Ай бұрын

    Тот момент когда на работе реально делать нечего

  • @marcovonkeman9449
    @marcovonkeman9449Ай бұрын

    Solution to the problem is shown after 5s in the video...

  • @basiliobastardo255
    @basiliobastardo25520 күн бұрын

    how do you know your tools is calibrated?

  • @user-ej4pp9xm2l
    @user-ej4pp9xm2lАй бұрын

    Ну всё, я пошёл гриндер покупать.

  • @londonalicante
    @londonalicanteАй бұрын

    All that effort is for nothing if you start that hole with that massive drill bit. Start your hole at a reasonably small size for accuracy, and lower the bit into the V block to find the centre.

  • @anatolisemenov8619
    @anatolisemenov8619Ай бұрын

    А призму выставить по сверлу не проще?

  • @_WingCommander
    @_WingCommander12 күн бұрын

    С чего вы взяли что ваша самоделка точно изготовлена и не врёт?

  • @IanCthrwd
    @IanCthrwd2 күн бұрын

    Waste of time. Lower the drill press bit till the end touches the top…learned in junior high woodshop.

  • @fernandoalves9942
    @fernandoalves9942Ай бұрын

    Amazing

  • @whiteflash72
    @whiteflash72Ай бұрын

    So how you gonna get that contraption off and keep the dowel in place ?

  • @sloanlance
    @sloanlance28 күн бұрын

    OK… And THEN what‽ This video shows 90% of the solution, then stops. #WTF‽

  • @williamwhy995
    @williamwhy99510 күн бұрын

    Facil fazer isso, qualquer um faz em casa mesmo

  • @davidguest5288
    @davidguest5288Ай бұрын

    £2.95 from Screwfix

  • @AbbeyBennyKIT
    @AbbeyBennyKITАй бұрын

    This is far from the best solution. Cut a V out of a square block. Drill a hole thru in the center of the V. Now flip it around, put your round piece in the V and drill from the opposite side. 😉

  • @morphix69
    @morphix69Ай бұрын

    try simply ruller method

  • @jamesbrother9597
    @jamesbrother9597Ай бұрын

    So, why didn't he use the drill that he just made that jig for?

  • @teb0072
    @teb0072Ай бұрын

    Or…. You could go to any Home Depot, Harbor Freight, etc. and buy the right tool for five bucks.

  • @blackthornknives
    @blackthornknivesАй бұрын

    Genius

  • @SANYA_YA
    @SANYA_YA8 күн бұрын

    В бруске ты просверлил, а в круге не смог?

  • @Prorab261
    @Prorab261Ай бұрын

    Линейку между деталью и сверлом, прижал чуток

  • @Blackrhino911
    @Blackrhino911Ай бұрын

    Please get a wood drill Set. That hurts to watsh.

  • @JaredTheGrayson
    @JaredTheGrayson6 күн бұрын

    BUT... after finding the center you have to move all that crap, to put your drill bit in the chuck... usless

Келесі