Варит не особо, я бы ток убавил и вел бы без лишних движений
@bayoutrapper3782Ай бұрын
Man I've been welding for over 30 years. And I've never been able to run a 6013, let alone a root. I've always worked in power plants, nuclear, and coal, paper Mills, code work. Mostly 100% x--ray. Which only require 6010, and 8018, stainless, inconel. My hats off you sir. God bless.😃
@mtdstc Жыл бұрын
Great video on how not to weld.
@b.p.rwebber8098
Жыл бұрын
Or what electrode not to use for a pipe root pass or any other pass.
@brk932
Жыл бұрын
6013 should give reasonable results...not pretty ... generally I would avoid on root welds because of how much slag and dirty finish they give. Also his current was too high to compensate for penetration ...but the result is still a BLOB
@dharmapatel5665
Жыл бұрын
Nice
@user-xn2uv8jy9g Жыл бұрын
Корневой валик огромный просто , должен быть от 0,5 мм до 3.0 мм . На моей работе меня бы наказали за это .
@user-xb7be1we8u
Жыл бұрын
это не валик, это что то, во первых в нормальных фирмах уже давно перешли на прямую полярность на корне, валик 0.5 до 3 мм максимум, где то вообще требуют заподлицо.
@arforse
Жыл бұрын
Есть требования вообще без валика когда жидкость текет самотёком не высокой тякучасти чтоб диаметр трубы в месте сварки не уменьшился
@user-cj1gy1jz9d
Жыл бұрын
На пищевом производстве вообще валик обратный не допускается!
@user-eh5ib8xx1s
Жыл бұрын
Большой ток для прохода корня. Ампер 70-75 похоже, прожигов много при сварке корня и валик больше чем нужно. Надо 55-60 ампер, самый Самолёт будет. И ВИК и Рентген 100% пройдёт.
@user-co2rv6vk1q
Жыл бұрын
от 0 до 3.0
@roywarriner8441 Жыл бұрын
In 40 years of pipefitting, I've never heard of a welding procedure using 6013 for the root pass.
@luciusirving5926
8 ай бұрын
Must be part cellulose.
@roywarriner8441
8 ай бұрын
@@luciusirving5926 Yeah, I know what the numbers mean, regardless, 6013 is not used in any welding procedure I know of. People not working in the industry wouldn't be expected to know what a welding procedure is. In 4 decades of working in the trade, the only time I've even seen it used was in school practicing running beads on scrap steel. You know, welding 101. Any welding on a vessel will follow a procedure even if it is just a bracket welded to the outside. For the purposes of legislation, any piping in a closed system is a vessel.
@Fakken28
4 ай бұрын
6010 root 7018 cap correct?
@roywarriner8441
4 ай бұрын
@@Fakken28 Yes, 6010 or 6011. 7018 fill and cap.
@user-jh9bc2yc1f Жыл бұрын
Лепила! Прихватки по кругу иначе поведёт
@andreA-zi6ez
Жыл бұрын
Качество - невпизду, но держаться будет
@user-cv8sp3zh3h Жыл бұрын
Это брак, кромки сжёг, рентген забракует!
@user-ql3lc6vm8d
6 ай бұрын
@user-cv8sp3zh3h ты хороший все Плохой.
@user-wx7nr9jc2d Жыл бұрын
Проффи,спец! Спасибо,всё показанно чётко! Удачи Вам и крепкого здоровья!
@jorgealvarofernandezacosta4801
Жыл бұрын
Traducelo al español....no se entiende nada absolutamente....
@diy_amin Жыл бұрын
ممنونم از وقت و انرژی که گذاشتین
@raulmarin8704 Жыл бұрын
For root pass you need to use 6010 not 6013
@terryandrews7271
Жыл бұрын
30 years of pipe welding and you are correct, 6010
@wasseemsaifi5091
Жыл бұрын
@Ахмет wellding wire thickness
@b.p.rwebber8098
Жыл бұрын
@@wasseemsaifi5091 no it doesn't mean thickness it is the electrode type.
@LrdBxRck
Жыл бұрын
I think I'm physically sick. I can kinda understand the 6013 so I'll give that a pass. But the build up on the interior wall is nasty at one point they switch to 7018 for the root. I guess going uphill was a plus but then they go downhill on the other side. The tacks were just huge bulbs.
@rubenbarria1557 Жыл бұрын
Muy buena soldadura! No cualquiera puede soldar asi!!
@truongsonnguyen19
Жыл бұрын
QqqqWA
@waltermaximilianocajal2992
Жыл бұрын
Qe lindo trabajo qe anperaje me recomienda para electrodo 2.5 mm tengo una inverter
@SenTirTv07 Жыл бұрын
Harus banyak belajar biar bisa mengelas seperti ini, terimakasih telah berbagi informasi ini.... salam Sejahtera
@jorgealvarofernandezacosta4801 Жыл бұрын
La raíz de la soldadura, se debe hacer con electrodo celulosico y no con electrodo rutilico
@husannurimov7014 Жыл бұрын
всё отлично но хочу смотреть 2.5 мм турбы как получится без перерыва сварки
@Wolframium65region Жыл бұрын
Посмотрел бы я на сварку этого "мастера " трубы хотябы 5 мм толщиной неговоря уже о 3мм или 2,5 мм . Разбарабанил корень шва и нашлаковал полюбому .
@carloshernandezespinoza1314 Жыл бұрын
Se recomienda usar 6010 para tuberos el trabajo es bueno suerte.
@duke6353 Жыл бұрын
Good job. What is the current and amp use for this work
@arnaulpujol8439 Жыл бұрын
Muy bueno quedo bien ahi saludos de Bs As
@almuntaseramer2168 Жыл бұрын
عند أول طبقة وهو الباص الأول كان لا بد من خفض الماكينة قليلا ومن ثم تردد يسير في سحب البركة إلى الأمام لكي تحافظ على نظافة اللحام و يظهر من الداخل مثل الخاتم متساوي في النفاذية
@imadhanafi5050
Жыл бұрын
كم قياس بوسط كم درجة حرارة صيفلو
@nathantrotter2509 Жыл бұрын
Mashallah. Brother your root opening it too wide for that process uphill 6013. The open root gap should only be 0.125 in at the most. Hope this helps 🙏
@Shalom194 Жыл бұрын
Gracias por la enseñanza, son meses o años para poder soldar de esa forma. Y muchos no consideran el esfuerzo.
@ernestofeliliz2537
Жыл бұрын
LA 6013 NO ES PARA ESO. ESA BARILLA NO TIENE SOPORTE.
@albertoruggeri7239
Жыл бұрын
Jajajaj enseñansa es cualquier cosa ...una burla
@tawfikMEGACAR Жыл бұрын
الله يبارك شغل جميل جدا
@jerrylance4932 Жыл бұрын
Wow, I remember when I didn’t know how to weld
@samehelgmal9796 Жыл бұрын
ما شاء الله جميل على سلك 6013 وغرز ممتاز 👍
@marcoturazza8473 Жыл бұрын
Un vero maestro della saldatura complimenti
@user-ge6hr1ti7y Жыл бұрын
От души Благодарим!
@arseniovera672 Жыл бұрын
Tenes que darles como raíz un celulosico ¡¡¡ luego luego como remates un buen básico. Y punto final. Saludos desde los lejos amigos. 🇦🇷🇦🇷🇦🇷🇦🇷🇦🇷🇦🇷🤔🤔🤔🤔🤔
@ltws6657 Жыл бұрын
Holy dingle berries. That was an awful root. 6010 is the right rod for the root pass on that job
@yamaguchi148 Жыл бұрын
Зазор меньше чуть. Ток при таком зазоре у вас очень большой. Начинают варить обычно с потолка, и для хорошей практики катушку нужно ставить 45 градусов.
@user-fc9ru6vp3p Жыл бұрын
لا توجد مشكله في لحام المعدن السميكه حتى من غير المحترفين ،،، الاسطى الحقيقي من يلحم المعادن الرقيقه
@ahmedkamal9634
Жыл бұрын
حسنت انا لحام كلفنايز 1 مليم
@lloydshackleton9554
Жыл бұрын
All this time I thought that's what the nob on the front of the machine was for. Well, shit.
@elgitano911
Жыл бұрын
Así es
@user-pk6cz9uk3g
Жыл бұрын
سر لحام المنيوم صعب
@JhonDiamond2021 Жыл бұрын
Welding Job, good job. keep your health and safety at work.
@user-yn3gf6xi5z Жыл бұрын
За такую сварку руки надо оторвать.
@MrYuriykost Жыл бұрын
Шов на теплотрассу, не более. Советую всем, кто варит трубу, обзавестись ПДУ. Это можно сделать самому, кто кулибин, и можно купить сварочный инвертор с устройством ПДУ. Кто варит, понимает! Не знаю откуда пошло, такая зачистка; выбирается по краям канавка вглубь. В эту канаву заходит шлак и попробуй его выдавить от туда! Загляните в инструкцию по сварке: конфигурация шва после зачистки должна быть с радиусом 3° в переходе от стенки стыка к основанию! А основание иметь ровную площадку или чуть (1 - 1,5 мм) вогнутую! Тогда без повышения А. меншим наплавленным металлом шлок сам уходит вверх и в стороны. Ему негде задерживаться, и некуда затекать! Ролик для начинающих. В моё время; это расцвет социализма с человеческим лицом, сварщики варили одной рукой. Я сам начал добавлять другую под 60. Всё думал, что нервы..., а как заметил, что и чашка с чаем трясётся у рта понял - время:/.
@DuniaFolding Жыл бұрын
Menurut saya pribadi sudah bagus 🙏hanya perlu kembangkan terus 🙏🙏
@user-nm8sp9wy8r Жыл бұрын
Сам не знаю и тебя научу!По больше таких видосов,чтобы конкурентов не было
@user-oj2qg4ll6q Жыл бұрын
Дуже добре! Професійна робота.👍👍👍
@JJS94 Жыл бұрын
Obrigado por demonstrar o tipo 6013🇧🇷
@rubenvera8026 Жыл бұрын
Pues de verdad que yo no recuerdo que en mis tiempos se hubiera usado 6013 mas que para herrería, para tubería sólo se usaba 6010 y7018, y cuando menos se hacian 2 cordones.
@gerardomoscoso5196 Жыл бұрын
En si para q se utiliza la 6013 ,para fondear oh darle vista
@luiscruzcruzado9578 Жыл бұрын
No estaría mal, que pusieras amperaje de raíz y peinado
@DesokyAbozid Жыл бұрын
ابتديت الفيرست ب6013 والكاب 7018 مع ان الفيرست لازم يكون 6010 لان 6013 سريع الترسيب ومن الصعب عمل فيرست بية بس الله ينور عليك
@victoralfonsomendozasoto9758 Жыл бұрын
que tipo de tuberia es =?
@robertoricci8775 Жыл бұрын
Comunque è il primo video che trovo di un impavido saldatore che salda un tubo con tanto di cianfrino in ascendente ne conosco pochi e sono dei veri professionisti👍
@moisesgaviriavallejo7553 Жыл бұрын
Muy bonito este cordón 😮
@cersosi19 Жыл бұрын
so, usually there’s only a 1/8 tolerance as far as the cap and that cap is enormous. i will say you got penetration which is huge for open root pipe welds. could’ve used a grinding wheel not a cutting wheel for getting your tack down haha. you opened you’re fit up a bit with it. you got it done, just a bit huge. You’re rod could’ve been a smaller one and done multiple passes, what is that 5/16? not sure if it called for that.
@GraniteRidge6 ай бұрын
What are the pipes started with a gap, why don't you push them together
@user-rk2pz8qb3z Жыл бұрын
Прихватка должно быт минимум 3 точку а то поведет. Зазор большовата или ток многовата чуто корену еле заварил.
@samumasih9529 Жыл бұрын
Penetration 6013 is not so good . 7018 performance is it mind blowing ..
@MikeSmith-su8ee Жыл бұрын
2.5 and electrode negative..tack welding outside the prepped area is a no go. Pipe at 45 degrees is a 6 G
@SergeyZhuravlev77 Жыл бұрын
Не вздумайте варить корень ТАК! У нас бы за это руки оторвали.
@billpickelheimer6323 Жыл бұрын
Probably should have feathered and cleaned those tack welds up, especially after seeing the gargantuan size , let alone all the horrid grinding on the pipe o.d.
@uniqko Жыл бұрын
Amazing skill
@hirsoniin5353 Жыл бұрын
thanks for the knowledge..
@hectorr814 Жыл бұрын
EXCELENTE VIDEO¡¡ .. GRACIAS POR COMPARTIR¡¡..SALUDOS DESDE MEXICO.
@israelnunezmeza45026 ай бұрын
Muy interesante gracias por compartir
@user-rw4jy6bx2l Жыл бұрын
هذا بسيط.... لحيم الفافون اصعب... افضل استخدام جهاز اللحيم القديم (الملف) لانه اكثر بناءا عند اللحيم
@alexandrzaharow3709 Жыл бұрын
Может и есть какие огрехи при проходе корня шва, но усиление шва изнутри и основной шов получились отличные - мастер варит, молодец !Потолок без отрыва во всех положениях при проходе корня - этому надо учиться долго . ...
@user-ic6rb8ti2h
Жыл бұрын
ну не совсем долго,это должно дано быть)если не дано,то как не учи,человек идеально варить не будет)
@viktor-jj7ym7dv9r
Жыл бұрын
А ржавчина почему не зачищена в околошовной зоне .
@AlexFcSumy1355
Жыл бұрын
Как у него не прогорает?)
@viktor-jj7ym7dv9r
Жыл бұрын
@@AlexFcSumy1355 оно и не будет прогорать , внутри получиться небольшая выпуклость до 2мм это хорошо, если больше то будет сильное завихрение , если труба идёт под пар и высокое давление
@user-ic6rb8ti2h
Жыл бұрын
@@AlexFcSumy1355 Ток очень маленький,низ и бока успевают структурироваться и держатся
@WaheedJaber Жыл бұрын
بالتو فيق ان شاء
@rahulbhardwaj6418 Жыл бұрын
Bro good welding
@imadhanafi5050 Жыл бұрын
كم قياس بوسط كم درجة الحرارة ضيفلو
@terryandrews7271 Жыл бұрын
6010 is all position rod, 6013 I believe is a straight rod for flat welding
@gregtipton2814
Жыл бұрын
6013 is an all position rod as well,the third number being a one tells you this
@terryandrews7271
Жыл бұрын
@@gregtipton2814 I welded for 30 years as a pipe welder, I was always taught by the old timers that we used 6010 for pipe. I'm 70 years old maybe things have thanks but 6010 It's different Then 6013
@gregtipton2814
Жыл бұрын
@@terryandrews7271 can't believe you've welded for 30years and don't know 6013is an all position rod,60 is tensile strength,1indicates ALL position,last number is type of flux,,I've welded for 40+years,6013 is low penetration rod but if your pipe is beveled reaching the bottom of your root pass shouldn't be a problem
@terryandrews7271
Жыл бұрын
@@gregtipton2814 Look this up smart ass see which one most Pipe fitters Weld with 6010 or 6013, Obviously was not permitted the education that you obviously think you have. You feel like you have to correct everybody, You're one of those guys most of my foremen were like you, They talked to talk but they couldn't walk the walk
@b.p.rwebber8098
Жыл бұрын
@@terryandrews7271 nope still the same. 6013 as you know is a general purpose rod that has low penetration and is never used on pipe or any heavy structure. 6010 is still the main electrode for pipe root passes and 7018 is still the eletrode for fill and cap on pipe and structural welds. Next this fellow is gonna start making heavy fabrication videos using 6013.
@DreamerDrafter Жыл бұрын
5G position welding with SMAW for pipe ...nice and right test for welder. Thank you for sharing this useful video Regards🌷🙏
@sheihjizzah5610 Жыл бұрын
Какой полярностью варили корень шва, обратной или прямой?
@terryandrews7271
Жыл бұрын
If it was straight polarity it would have sounded like a mad bumblebee
@sheihjizzah5610
Жыл бұрын
@@terryandrews7271 Спасибо отличная работа👍
@willemf9885 Жыл бұрын
That gas... not healthy, i think?
@omarperez9162 Жыл бұрын
La soldadura 6013 produce mucha escoria ,y se te puede apagar el circuito,,pero tiene buena penetración
@bateriasinsecretos369
Жыл бұрын
Omar, se usa el 13 o podría ser 10 también, por qué es la raíz de la soldadura, el tipo de aleación que tiene es mucho más fuerte. Luego le hace la terminación con 7018 por qué te permite dejar un cordón uniforme . Una mantequita! Saludos! ( Obviamente es lo que yo sé y lo comparto, no quiere decir que sea así 😀)
@michaelshortridge6379 Жыл бұрын
Root or 1st pass had excessive penetration. Rest looked ok.
@terryandrews7271
Жыл бұрын
I agree I was a pipewelder for 30 years too much push, Too much penetration. Keep practicing Keep practicing
@rauloribe2428 Жыл бұрын
Crítica.Dónde está el protector de la amoladora?
@wueiwuusw5087 Жыл бұрын
5g 6013 bạn làm rất tốt.
@bidursethi2902 Жыл бұрын
Parece que es el electrodo E 7018 de hecho hay mucha differential con 6013
@punkbadai8013 Жыл бұрын
Jika dilihat dari dalam pipa, maka bisa dipastikan penetrasi elektroda terlalu dalam yang menghasilkan ketebalan lebih dari 2mm
@user-jo9tr4tn6i Жыл бұрын
в чем секрет этой сварки.
@Strengthandconditioning60 Жыл бұрын
I was a welder and uh..no. This has got to be a student
@owenarnaiz5921
Жыл бұрын
Good root for penetration is 6011.
@chrisjones2224
Жыл бұрын
It's Stevie Wonder, apparently he has a few welding videos on KZread, must be his new hobby
@hakimabdelasiz1390 Жыл бұрын
تحياتي لكم
@miha7784 Жыл бұрын
Во первых такой диаметр трубы варят тройкой, а во-вторых внутренний шов должен быть заполецо со стеной трубы (а у вас выступает) и в третих хороший сварщик варит трубы одной рукой
@wandofiuza8425 Жыл бұрын
Super profissiinal. Parabéns. Soldagem perfeita
@guymolla9353
Жыл бұрын
Le pauvre,il Lui faut un bon,bon, bon Professeur !!!!😱😱
@jewellerydesignerartists9353 Жыл бұрын
Nice work 🙏 Have a great day 😊🔔🔔
@leandrodemourasantos3436 Жыл бұрын
Qual a espessura do tubo e a amperagem usada ? Qual a medida do eletrodo?
@tomascastro4154
Жыл бұрын
3 octavos espesura, 1 octavo electrodo, amperes varía entre 100 y 120 más o menos
@user-ic6rb8ti2h Жыл бұрын
Все вроде нормас,но учитывая что толщина стенки более 4 мм,нужна только фаска,такой зазор как оставил сварщик,по госту не положен)
@user-lp8nh1bz9k
Жыл бұрын
Всех учат по разному меня учили металл 3мм зазор не выстовляется
@user-ic6rb8ti2h
Жыл бұрын
@@user-lp8nh1bz9k Видать вас учили не совсем по ГОСТу)
@AlexFcSumy1355
Жыл бұрын
@@user-lp8nh1bz9k мне говорили что от 3мм надо уже зазор оставлять
@user-uj1iq7sk4i Жыл бұрын
Классная работа!!!
@jesusjuanillo3465 Жыл бұрын
A qué amperaje estás aplicando la soldadura ?? saludos desde León GTO México 👍
@jorgecastilo605 Жыл бұрын
Me vas a disculpar, lo que a mí me parece es un cordón con electrodo 7018, y no de 6013.
@user-vq7ho9wj5q Жыл бұрын
Excellent professional 100fil100
@richardwich3492 Жыл бұрын
If I were you, I'd be applying a down hand maintenance weld with a(6013) Mild steel electrode. "I'm not even lying"
@nagialjunior Жыл бұрын
Good job 👍👍👍
@DT-abcd Жыл бұрын
Gap too big. Too low a current. Will have cold joints
@user-pl8jh6hx5m Жыл бұрын
вот это сварка я понимаю а то сверху наплавят,и говорчт я сварил.браво.
@user-fw2vl2ls7t Жыл бұрын
Фаска с очень малым притуплением для такой толщины стенок трубы.Внутри очень вылезает шов.Электрод тройка не пойдёт.Видно что ток выставленный не справляется с наплавкой шва по фаске.Нужно было 2.5мм для корня брать а перекрывать уже 3мм электродом.
@raymundotoledo8019 Жыл бұрын
La verdad es que 6013 no es óptima para raíz..se ve el esfuerzo por querer aserlo bien. Pero la aplicación es incorrecta ..pasear el arco muy largo no es lo indicado . Tal ves si tuviera más grueso el oombro que el electrodo no abría nesecidad de desperdiciar tanto calor en los viajes largos del electrodo.ya que 6013 no es de solidificación rapida.rápida.. saludos desde dallas tx
@TheUltimate65 Жыл бұрын
What not det up the pipe in 45 degrise angel and weld in G6 position
@luciusirving59268 ай бұрын
ESAB's 6013s autoclean like 7018 and my Lincoln 6013s never did that before. Taking slag off of a Lincoln 6013 was too much work. 6013 flux compositions are confusing.
@user-nc5in7ff3v Жыл бұрын
Классный и поучительный видос.Спасибо!!!!!!
@user-wd8go9ob1q Жыл бұрын
Переменный ток... Слишком высокое напряжение из-за чего отводится тепло на кромки.не зачищены. Непрофессионально.но для непрофессионала отлично.
@holgergerlach8651 Жыл бұрын
Die Parameter von der Wurzel währen natürlich auch interessant! !!!!
@user-es9dx1ep7m Жыл бұрын
Корень вариться колебания от кромки до кромки но ни как в вех низ. Неправильно братуха показываешь просветку не пройдет.
@josealves9389 Жыл бұрын
Gostei essa é o teste 6 g passei Porto isso e isso ai amigo
@user-hi3jj6vl1t Жыл бұрын
Пойдет.. Только по-моему ток великоват. Ну об этом сварные с трубы лучше объяснят.
@user-vh9it2lr6n Жыл бұрын
Так нельзя варить корень .При всем уважении.При такой стенки металла ,желательно 2,6 диаметром электрода пользоваться. А так для воды нормально будет,не категория .
@michaelvanpeski8140 Жыл бұрын
The gap was entirely too wide! And also a 6010 rod is a much better rod for the root! Just my opinion.
@vagnerjoserodriguesvieira1004 Жыл бұрын
Muito bom trabalho, orientação valiosa. Ver esse profissional trabalhar e incentivador .
@mennaaisouhilmicano Жыл бұрын
طبقة اللحام الاولى كانت سيئة وغير متجانسة لو تفحص بالأشعة ستجدها حتما مليئة بالجيوب الهوائية اما الطبقة والوسطى والنهائية ممتازتان
Пікірлер: 353
Варит не особо, я бы ток убавил и вел бы без лишних движений
Man I've been welding for over 30 years. And I've never been able to run a 6013, let alone a root. I've always worked in power plants, nuclear, and coal, paper Mills, code work. Mostly 100% x--ray. Which only require 6010, and 8018, stainless, inconel. My hats off you sir. God bless.😃
Great video on how not to weld.
@b.p.rwebber8098
Жыл бұрын
Or what electrode not to use for a pipe root pass or any other pass.
@brk932
Жыл бұрын
6013 should give reasonable results...not pretty ... generally I would avoid on root welds because of how much slag and dirty finish they give. Also his current was too high to compensate for penetration ...but the result is still a BLOB
@dharmapatel5665
Жыл бұрын
Nice
Корневой валик огромный просто , должен быть от 0,5 мм до 3.0 мм . На моей работе меня бы наказали за это .
@user-xb7be1we8u
Жыл бұрын
это не валик, это что то, во первых в нормальных фирмах уже давно перешли на прямую полярность на корне, валик 0.5 до 3 мм максимум, где то вообще требуют заподлицо.
@arforse
Жыл бұрын
Есть требования вообще без валика когда жидкость текет самотёком не высокой тякучасти чтоб диаметр трубы в месте сварки не уменьшился
@user-cj1gy1jz9d
Жыл бұрын
На пищевом производстве вообще валик обратный не допускается!
@user-eh5ib8xx1s
Жыл бұрын
Большой ток для прохода корня. Ампер 70-75 похоже, прожигов много при сварке корня и валик больше чем нужно. Надо 55-60 ампер, самый Самолёт будет. И ВИК и Рентген 100% пройдёт.
@user-co2rv6vk1q
Жыл бұрын
от 0 до 3.0
In 40 years of pipefitting, I've never heard of a welding procedure using 6013 for the root pass.
@luciusirving5926
8 ай бұрын
Must be part cellulose.
@roywarriner8441
8 ай бұрын
@@luciusirving5926 Yeah, I know what the numbers mean, regardless, 6013 is not used in any welding procedure I know of. People not working in the industry wouldn't be expected to know what a welding procedure is. In 4 decades of working in the trade, the only time I've even seen it used was in school practicing running beads on scrap steel. You know, welding 101. Any welding on a vessel will follow a procedure even if it is just a bracket welded to the outside. For the purposes of legislation, any piping in a closed system is a vessel.
@Fakken28
4 ай бұрын
6010 root 7018 cap correct?
@roywarriner8441
4 ай бұрын
@@Fakken28 Yes, 6010 or 6011. 7018 fill and cap.
Лепила! Прихватки по кругу иначе поведёт
@andreA-zi6ez
Жыл бұрын
Качество - невпизду, но держаться будет
Это брак, кромки сжёг, рентген забракует!
@user-ql3lc6vm8d
6 ай бұрын
@user-cv8sp3zh3h ты хороший все Плохой.
Проффи,спец! Спасибо,всё показанно чётко! Удачи Вам и крепкого здоровья!
@jorgealvarofernandezacosta4801
Жыл бұрын
Traducelo al español....no se entiende nada absolutamente....
ممنونم از وقت و انرژی که گذاشتین
For root pass you need to use 6010 not 6013
@terryandrews7271
Жыл бұрын
30 years of pipe welding and you are correct, 6010
@wasseemsaifi5091
Жыл бұрын
@Ахмет wellding wire thickness
@b.p.rwebber8098
Жыл бұрын
@@wasseemsaifi5091 no it doesn't mean thickness it is the electrode type.
@LrdBxRck
Жыл бұрын
I think I'm physically sick. I can kinda understand the 6013 so I'll give that a pass. But the build up on the interior wall is nasty at one point they switch to 7018 for the root. I guess going uphill was a plus but then they go downhill on the other side. The tacks were just huge bulbs.
Muy buena soldadura! No cualquiera puede soldar asi!!
@truongsonnguyen19
Жыл бұрын
QqqqWA
@waltermaximilianocajal2992
Жыл бұрын
Qe lindo trabajo qe anperaje me recomienda para electrodo 2.5 mm tengo una inverter
Harus banyak belajar biar bisa mengelas seperti ini, terimakasih telah berbagi informasi ini.... salam Sejahtera
La raíz de la soldadura, se debe hacer con electrodo celulosico y no con electrodo rutilico
всё отлично но хочу смотреть 2.5 мм турбы как получится без перерыва сварки
Посмотрел бы я на сварку этого "мастера " трубы хотябы 5 мм толщиной неговоря уже о 3мм или 2,5 мм . Разбарабанил корень шва и нашлаковал полюбому .
Se recomienda usar 6010 para tuberos el trabajo es bueno suerte.
Good job. What is the current and amp use for this work
Muy bueno quedo bien ahi saludos de Bs As
عند أول طبقة وهو الباص الأول كان لا بد من خفض الماكينة قليلا ومن ثم تردد يسير في سحب البركة إلى الأمام لكي تحافظ على نظافة اللحام و يظهر من الداخل مثل الخاتم متساوي في النفاذية
@imadhanafi5050
Жыл бұрын
كم قياس بوسط كم درجة حرارة صيفلو
Mashallah. Brother your root opening it too wide for that process uphill 6013. The open root gap should only be 0.125 in at the most. Hope this helps 🙏
Gracias por la enseñanza, son meses o años para poder soldar de esa forma. Y muchos no consideran el esfuerzo.
@ernestofeliliz2537
Жыл бұрын
LA 6013 NO ES PARA ESO. ESA BARILLA NO TIENE SOPORTE.
@albertoruggeri7239
Жыл бұрын
Jajajaj enseñansa es cualquier cosa ...una burla
الله يبارك شغل جميل جدا
Wow, I remember when I didn’t know how to weld
ما شاء الله جميل على سلك 6013 وغرز ممتاز 👍
Un vero maestro della saldatura complimenti
От души Благодарим!
Tenes que darles como raíz un celulosico ¡¡¡ luego luego como remates un buen básico. Y punto final. Saludos desde los lejos amigos. 🇦🇷🇦🇷🇦🇷🇦🇷🇦🇷🇦🇷🤔🤔🤔🤔🤔
Holy dingle berries. That was an awful root. 6010 is the right rod for the root pass on that job
Зазор меньше чуть. Ток при таком зазоре у вас очень большой. Начинают варить обычно с потолка, и для хорошей практики катушку нужно ставить 45 градусов.
لا توجد مشكله في لحام المعدن السميكه حتى من غير المحترفين ،،، الاسطى الحقيقي من يلحم المعادن الرقيقه
@ahmedkamal9634
Жыл бұрын
حسنت انا لحام كلفنايز 1 مليم
@lloydshackleton9554
Жыл бұрын
All this time I thought that's what the nob on the front of the machine was for. Well, shit.
@elgitano911
Жыл бұрын
Así es
@user-pk6cz9uk3g
Жыл бұрын
سر لحام المنيوم صعب
Welding Job, good job. keep your health and safety at work.
За такую сварку руки надо оторвать.
Шов на теплотрассу, не более. Советую всем, кто варит трубу, обзавестись ПДУ. Это можно сделать самому, кто кулибин, и можно купить сварочный инвертор с устройством ПДУ. Кто варит, понимает! Не знаю откуда пошло, такая зачистка; выбирается по краям канавка вглубь. В эту канаву заходит шлак и попробуй его выдавить от туда! Загляните в инструкцию по сварке: конфигурация шва после зачистки должна быть с радиусом 3° в переходе от стенки стыка к основанию! А основание иметь ровную площадку или чуть (1 - 1,5 мм) вогнутую! Тогда без повышения А. меншим наплавленным металлом шлок сам уходит вверх и в стороны. Ему негде задерживаться, и некуда затекать! Ролик для начинающих. В моё время; это расцвет социализма с человеческим лицом, сварщики варили одной рукой. Я сам начал добавлять другую под 60. Всё думал, что нервы..., а как заметил, что и чашка с чаем трясётся у рта понял - время:/.
Menurut saya pribadi sudah bagus 🙏hanya perlu kembangkan terus 🙏🙏
Сам не знаю и тебя научу!По больше таких видосов,чтобы конкурентов не было
Дуже добре! Професійна робота.👍👍👍
Obrigado por demonstrar o tipo 6013🇧🇷
Pues de verdad que yo no recuerdo que en mis tiempos se hubiera usado 6013 mas que para herrería, para tubería sólo se usaba 6010 y7018, y cuando menos se hacian 2 cordones.
En si para q se utiliza la 6013 ,para fondear oh darle vista
No estaría mal, que pusieras amperaje de raíz y peinado
ابتديت الفيرست ب6013 والكاب 7018 مع ان الفيرست لازم يكون 6010 لان 6013 سريع الترسيب ومن الصعب عمل فيرست بية بس الله ينور عليك
que tipo de tuberia es =?
Comunque è il primo video che trovo di un impavido saldatore che salda un tubo con tanto di cianfrino in ascendente ne conosco pochi e sono dei veri professionisti👍
Muy bonito este cordón 😮
so, usually there’s only a 1/8 tolerance as far as the cap and that cap is enormous. i will say you got penetration which is huge for open root pipe welds. could’ve used a grinding wheel not a cutting wheel for getting your tack down haha. you opened you’re fit up a bit with it. you got it done, just a bit huge. You’re rod could’ve been a smaller one and done multiple passes, what is that 5/16? not sure if it called for that.
What are the pipes started with a gap, why don't you push them together
Прихватка должно быт минимум 3 точку а то поведет. Зазор большовата или ток многовата чуто корену еле заварил.
Penetration 6013 is not so good . 7018 performance is it mind blowing ..
2.5 and electrode negative..tack welding outside the prepped area is a no go. Pipe at 45 degrees is a 6 G
Не вздумайте варить корень ТАК! У нас бы за это руки оторвали.
Probably should have feathered and cleaned those tack welds up, especially after seeing the gargantuan size , let alone all the horrid grinding on the pipe o.d.
Amazing skill
thanks for the knowledge..
EXCELENTE VIDEO¡¡ .. GRACIAS POR COMPARTIR¡¡..SALUDOS DESDE MEXICO.
Muy interesante gracias por compartir
هذا بسيط.... لحيم الفافون اصعب... افضل استخدام جهاز اللحيم القديم (الملف) لانه اكثر بناءا عند اللحيم
Может и есть какие огрехи при проходе корня шва, но усиление шва изнутри и основной шов получились отличные - мастер варит, молодец !Потолок без отрыва во всех положениях при проходе корня - этому надо учиться долго . ...
@user-ic6rb8ti2h
Жыл бұрын
ну не совсем долго,это должно дано быть)если не дано,то как не учи,человек идеально варить не будет)
@viktor-jj7ym7dv9r
Жыл бұрын
А ржавчина почему не зачищена в околошовной зоне .
@AlexFcSumy1355
Жыл бұрын
Как у него не прогорает?)
@viktor-jj7ym7dv9r
Жыл бұрын
@@AlexFcSumy1355 оно и не будет прогорать , внутри получиться небольшая выпуклость до 2мм это хорошо, если больше то будет сильное завихрение , если труба идёт под пар и высокое давление
@user-ic6rb8ti2h
Жыл бұрын
@@AlexFcSumy1355 Ток очень маленький,низ и бока успевают структурироваться и держатся
بالتو فيق ان شاء
Bro good welding
كم قياس بوسط كم درجة الحرارة ضيفلو
6010 is all position rod, 6013 I believe is a straight rod for flat welding
@gregtipton2814
Жыл бұрын
6013 is an all position rod as well,the third number being a one tells you this
@terryandrews7271
Жыл бұрын
@@gregtipton2814 I welded for 30 years as a pipe welder, I was always taught by the old timers that we used 6010 for pipe. I'm 70 years old maybe things have thanks but 6010 It's different Then 6013
@gregtipton2814
Жыл бұрын
@@terryandrews7271 can't believe you've welded for 30years and don't know 6013is an all position rod,60 is tensile strength,1indicates ALL position,last number is type of flux,,I've welded for 40+years,6013 is low penetration rod but if your pipe is beveled reaching the bottom of your root pass shouldn't be a problem
@terryandrews7271
Жыл бұрын
@@gregtipton2814 Look this up smart ass see which one most Pipe fitters Weld with 6010 or 6013, Obviously was not permitted the education that you obviously think you have. You feel like you have to correct everybody, You're one of those guys most of my foremen were like you, They talked to talk but they couldn't walk the walk
@b.p.rwebber8098
Жыл бұрын
@@terryandrews7271 nope still the same. 6013 as you know is a general purpose rod that has low penetration and is never used on pipe or any heavy structure. 6010 is still the main electrode for pipe root passes and 7018 is still the eletrode for fill and cap on pipe and structural welds. Next this fellow is gonna start making heavy fabrication videos using 6013.
5G position welding with SMAW for pipe ...nice and right test for welder. Thank you for sharing this useful video Regards🌷🙏
Какой полярностью варили корень шва, обратной или прямой?
@terryandrews7271
Жыл бұрын
If it was straight polarity it would have sounded like a mad bumblebee
@sheihjizzah5610
Жыл бұрын
@@terryandrews7271 Спасибо отличная работа👍
That gas... not healthy, i think?
La soldadura 6013 produce mucha escoria ,y se te puede apagar el circuito,,pero tiene buena penetración
@bateriasinsecretos369
Жыл бұрын
Omar, se usa el 13 o podría ser 10 también, por qué es la raíz de la soldadura, el tipo de aleación que tiene es mucho más fuerte. Luego le hace la terminación con 7018 por qué te permite dejar un cordón uniforme . Una mantequita! Saludos! ( Obviamente es lo que yo sé y lo comparto, no quiere decir que sea así 😀)
Root or 1st pass had excessive penetration. Rest looked ok.
@terryandrews7271
Жыл бұрын
I agree I was a pipewelder for 30 years too much push, Too much penetration. Keep practicing Keep practicing
Crítica.Dónde está el protector de la amoladora?
5g 6013 bạn làm rất tốt.
Parece que es el electrodo E 7018 de hecho hay mucha differential con 6013
Jika dilihat dari dalam pipa, maka bisa dipastikan penetrasi elektroda terlalu dalam yang menghasilkan ketebalan lebih dari 2mm
в чем секрет этой сварки.
I was a welder and uh..no. This has got to be a student
@owenarnaiz5921
Жыл бұрын
Good root for penetration is 6011.
@chrisjones2224
Жыл бұрын
It's Stevie Wonder, apparently he has a few welding videos on KZread, must be his new hobby
تحياتي لكم
Во первых такой диаметр трубы варят тройкой, а во-вторых внутренний шов должен быть заполецо со стеной трубы (а у вас выступает) и в третих хороший сварщик варит трубы одной рукой
Super profissiinal. Parabéns. Soldagem perfeita
@guymolla9353
Жыл бұрын
Le pauvre,il Lui faut un bon,bon, bon Professeur !!!!😱😱
Nice work 🙏 Have a great day 😊🔔🔔
Qual a espessura do tubo e a amperagem usada ? Qual a medida do eletrodo?
@tomascastro4154
Жыл бұрын
3 octavos espesura, 1 octavo electrodo, amperes varía entre 100 y 120 más o menos
Все вроде нормас,но учитывая что толщина стенки более 4 мм,нужна только фаска,такой зазор как оставил сварщик,по госту не положен)
@user-lp8nh1bz9k
Жыл бұрын
Всех учат по разному меня учили металл 3мм зазор не выстовляется
@user-ic6rb8ti2h
Жыл бұрын
@@user-lp8nh1bz9k Видать вас учили не совсем по ГОСТу)
@AlexFcSumy1355
Жыл бұрын
@@user-lp8nh1bz9k мне говорили что от 3мм надо уже зазор оставлять
Классная работа!!!
A qué amperaje estás aplicando la soldadura ?? saludos desde León GTO México 👍
Me vas a disculpar, lo que a mí me parece es un cordón con electrodo 7018, y no de 6013.
Excellent professional 100fil100
If I were you, I'd be applying a down hand maintenance weld with a(6013) Mild steel electrode. "I'm not even lying"
Good job 👍👍👍
Gap too big. Too low a current. Will have cold joints
вот это сварка я понимаю а то сверху наплавят,и говорчт я сварил.браво.
Фаска с очень малым притуплением для такой толщины стенок трубы.Внутри очень вылезает шов.Электрод тройка не пойдёт.Видно что ток выставленный не справляется с наплавкой шва по фаске.Нужно было 2.5мм для корня брать а перекрывать уже 3мм электродом.
La verdad es que 6013 no es óptima para raíz..se ve el esfuerzo por querer aserlo bien. Pero la aplicación es incorrecta ..pasear el arco muy largo no es lo indicado . Tal ves si tuviera más grueso el oombro que el electrodo no abría nesecidad de desperdiciar tanto calor en los viajes largos del electrodo.ya que 6013 no es de solidificación rapida.rápida.. saludos desde dallas tx
What not det up the pipe in 45 degrise angel and weld in G6 position
ESAB's 6013s autoclean like 7018 and my Lincoln 6013s never did that before. Taking slag off of a Lincoln 6013 was too much work. 6013 flux compositions are confusing.
Классный и поучительный видос.Спасибо!!!!!!
Переменный ток... Слишком высокое напряжение из-за чего отводится тепло на кромки.не зачищены. Непрофессионально.но для непрофессионала отлично.
Die Parameter von der Wurzel währen natürlich auch interessant! !!!!
Корень вариться колебания от кромки до кромки но ни как в вех низ. Неправильно братуха показываешь просветку не пройдет.
Gostei essa é o teste 6 g passei Porto isso e isso ai amigo
Пойдет.. Только по-моему ток великоват. Ну об этом сварные с трубы лучше объяснят.
Так нельзя варить корень .При всем уважении.При такой стенки металла ,желательно 2,6 диаметром электрода пользоваться. А так для воды нормально будет,не категория .
The gap was entirely too wide! And also a 6010 rod is a much better rod for the root! Just my opinion.
Muito bom trabalho, orientação valiosa. Ver esse profissional trabalhar e incentivador .
طبقة اللحام الاولى كانت سيئة وغير متجانسة لو تفحص بالأشعة ستجدها حتما مليئة بالجيوب الهوائية اما الطبقة والوسطى والنهائية ممتازتان
@L_E_L_0_U_P
Ай бұрын
Heat was too high for the root weld