Not sure what is scarier. The fact is hat he fixed the flywheel like this, or the fact that it looks like he did it before

The stress cracks are from extreme heat 🔥 Thats why the center exploded out , It is permanently ruined . Nothing can be done to fix it ! It will explode with even greater Force next time ! Its a Time Bomb with an extremely short fuze

@horstmuller7512

Ай бұрын

What's going to happen when the part explodes after some miles? In worst case, it will kill the driver and a few passers-by on the road. It's Pakistan, where life is cheap and short.

@jimsworthow531

Ай бұрын

so true; imagine the heat that the slipping clutch that failed looked like?

@dusterowner9978

Ай бұрын

They polished a turd and did a fine job ! Don't want to be around that when it lets loose again .

@chrisjarvis4449

29 күн бұрын

these videos are just money grab videos there just trying to make a buck

@horstmuller7512

29 күн бұрын

@@chrisjarvis4449 Can't be true. Intention of all these world-famous "super high skilled professionals" is not making money with crap videos. These world-famous specialists are proud of their work just using a sledgehammer while crawling in the dirt. They have remained small children who have very little understanding of decadent Western technology. Even the innards of these new gasoline donkeys will overwhelm most of them. Yes, it's sad but true: Most of these workers don't survive a full year, or if they do, with chopped off hands and feet and a fatal lung disease. Life in Pakistan is short and cheap.

I'm impressed you repaired what you did with the parts you have, unfortunately strengthening the weakest part now ensures the net time that massively cracked flywheel fails it will do so spectacularly with shards of steel flying in every direction at high rpm likely taking out the driver and any close pedestrians. (Slow clap)

Set-screws to hold that piece in? No way. At least run a V groove between new metal piece and old metal flywheel, then weld it, then cut/shave it flush on the lathe. Would have taken the same amount of time and is stronger.

The flywheel is knackered and ready to go bang

Не , ну не выбрасывать же ! 🤣🤣🤣 . Скорее всего эта комедия снимается только для контента , ежу понятно что работать не будет .

@meppaca

Ай бұрын

У меня тоже закралось такое подозрение после склеивания осей и коленвалов.

@user-wk2rg9qm6d

Ай бұрын

все будет работать , и достаточно долго !

Some one is going to wear that flywheel .

there is three ways to do a job ..... the right way , the wrong way, and the way we are going to do it. rock on

А где сварка? 🤣

@Cepera03

Ай бұрын

Читай название внимательней "Если закончились электроды."😁

A lot of work just for a coaster for flower pots.

Aufgepasst! Der neue Look von unseren LOCTITE Schraubensicherungen! kzread.info/dash/bejne/qK6hz7V6qL3Wpdo.html Watch out! The new look from our Loctite screw fuses! & Press seats

С такими трещинами ему давно пора в переплавку. Это какие ж нагрузки испытывает коленвал, чтобы маховик так разорвать?

@user-ss7lz5ls8w

Ай бұрын

Там скорее всего всё разорвало... Маховик вырвало, трещины жесть, нагрузка была бешаная. Посадили на резьбу кусок пластилина и двумя болтиками на 6 зафиксировали😂

@servis-Ural

Ай бұрын

Да не, маховик уже восстановленный был, второй раз делают кажется

@user-ss7lz5ls8w

Ай бұрын

@@servis-Ural Если не в десятый 🤣

Маховик протачивается от привалочной базы которая прилегает к коленвалу а тут не факт что геометрия будет

Пару раз видал как на ходу разваливаются тормозные диски. И это было очень опасно. Что случиться если развалится махових даже думать больно.

Золотые руки мастеров!Молодцы!Здоровья и благополучия Вам!

Маховик весь в трещинах, он перегрет 20 раз, стоит ли так делать? Это если доехать до базы, МАКСИМУМ.

Gee, Um..... I don't know what to say. Wouldn't you run a weld around the joint ?. Or just buy a good used flywheel !.

@martin-vv9lf

Ай бұрын

it's cast iron, won't take a weld. i would have peened off those two bolts with a hammer to swell them and prevent from shaking loose, then ground them down. i think it will hold but it would have been safer to make an entire flywheel from mild steel on the lathe and transfer over the starter ring. he had all the tools there to do it, and the work would have been about the same.

@martinswiney2192

Ай бұрын

You can weld cast iron with a nickel 55 or nickel 99 rod or wire. You can also use 316 stainless rods or wire and it will not harden like if welded with mild steel. But none of that matters when the flywheel is scrap to begin with. Also what a sweet piece of locally smelted chunk-o-scrap to make the plug out of.

@randie9480

Ай бұрын

​@martinswiney2192 the weld itself won't be hard but the haz zone will be unless you pre heat the cast iron to 700°

@SK-tr9ii

Ай бұрын

@@martin-vv9lf It's not cast iron, it's cast steel which has different properties all together.

Merhaba çok güzel bir video olmuş 👍

Good enough for where they live

Esa reparacin puede funcionar para pequeñas poleas de fajas en motores eléctricos, Para una volante que absorve y entrega energia cinética producto de las millones de explosiones de los cilindros del motor, se arloja y se sale el postizo.

Excelente, Super profissional!

That lathe tool looked worse than the fly wheel.

Этот маховик на мусорку опоздал..

At least cross drill and pin it … imagine that thing sawing through the bell housing

Мастер красавчик 👍

Так при включении задней двигатель то в другую сторону начнет работать и все открутится ... Ребята нужна сварка....только сварка...прям к колену варить и шатунам😂

@sasapups

Ай бұрын

Это с каких пор?

Gran trabajo,felicidades y que tengas buen dia...🐧

Man, people in Pakistan have high pitched voices.

They are not capitalism. It's easy to replace it, but making an old material last a hundred thousand miles feels amazing. That's his honest job. If it doesn't work, he probably won't repair it.

This man is one of the best machinists I have ever seen with a great vision of how to repair things and the tools he creates to do the repairs as with the grinder attachment to surface the flywheel. That flywheel has multiple cracks, and its life is limited, but they have to make do with what they have!!!

@snowflakemelter1172

Ай бұрын

We found the guy that have no clue what he's talking about.

@horstmuller7512

Ай бұрын

This guy is an idiot. He probably will kill his customer when he uses this "repaired" flywheel.

@baoyen7235

Ай бұрын

Ở Việt Nam tôi thợ giỏi như này có nhiều lắm.

How to make a frag grenade the hard way :D

Занятся нечем.ремонт маховика с трещинами.

Nice sharing Vidio...Very useful and useful Always successful friends .Greeting from Indonesian traditional gold prospecting 🇮🇩💓👍👍

@CNCMaster00

Ай бұрын

Thanks

Меня одного смутили трещины по привалочной плоскости диска сцепления? Хотя работать будет, но как долго? Или опять - сварка-балгарка- станок! 💪🤷🏻‍♂️😆😆😆

flywheel full of cracks and fissures pour some epoxy n grind off😀

Sometimes you just gotta turn loose of a few bucks and buy a (GASP!) new part. Ockmed is gonna need some new legs when that piece of scrap metal lets loose and comes through the floor of the truck.

Так я не понял , а как-же сварка , нужно было заварить 😮

@Cepera03

Ай бұрын

В соседний сарай почему то не завезли электродную проволоку!😁

Нет такой детали в автомобиле чтобы они не восстановили.молодцы.удачи.

I really enjoyed seeing the work he did. But I would buy a different fly wheel that didn't have all those cracks in it. I would be very worried that that fly wheel would eventually fly apart. Sometimes the part is too far gone to repair and still be safe to use. Great video though.

@cameronlilly4814

Ай бұрын

'Not sure about the cracks being an issue; just like brake disks, they develop surface cracks due to friction heating. I suspect they are more of an appearance issue than a structural one. All things being equal a scatter-shield would still be nice...

So Amazing!!!

@CNCMaster00

Ай бұрын

Thanks

Хотя бы на фиксатор резьбы приклеил бы.

@MrAlexUssR

Ай бұрын

там два болтик на 6. Это крепче ))))

Das Schwungrad ist kaputt. Was treibt ihr da 😅😂?

I wouldn't use that flywheel, too many cracks

It's now a bomb waiting to go off. All those heat stress cracks will eventually fail, and I doubt the bell housing will be of much protection.

Formidables les gars

🏁🏁👍❤️🇩🇰

Wonder if Boeing subbed out to these guys

@martinswiney2192

Ай бұрын

Soon to be landing in a back yard near you. Lol.

@precisiond2236

Ай бұрын

I worked at Boeing. Looks like part of the team.

Uma dúvida isso tá só enroscado?.se sim vai sair🤦‍♂️😅

There is no way those 2 bolts will stop that centre unscrewing, threading it in was a terrible idea, the entire torque and weight of the truck in drive and overrun will eat it alive, I imagine those 2 bolts are the lowest grade a bolt can be, if it had 6 x 12.9 grade it would be a start but it'll still fail. Lets hope it's just temporary so it can slowly creep to the flywheel shop a few miles away.

Ребята конечно молодцы, но работать это не будет, и даже очень опасно.

So this is how they make a bouncing betty mine

Ek bi full nei he Kaya hua,?

Our friend is a man of many talents as soon as l saw the problem I knew instinctively how he was going to respond and I was 💯% spot on at the end of the day this is one guy that can make your day better if you are the client

Respekt Meister ❤❤

@CNCMaster00

Ай бұрын

Thanks

@user-il7ot4ns4i

Ай бұрын

мастера? халтура!!!

hmm

Brilliant, but is the old part worth the hassle repairing

Точность офигенная!😅

👍👍👍👍👍

@CNCMaster00

Ай бұрын

Thanks

Cool work thanks 👍

@CNCMaster00

Ай бұрын

Thanks

👌👌👍👍

а он развалиться, к бабке не ходи

Бесполезная работа . Такую деталь опасно устанавливать

wahhhhhhhhhhhhhhhhhhhhhhhhhh

После этого ремонта я могу смело сказать што уже видел всё интересно только одно куда полетит водитель когда это говно оторвется

Нихуя и них гонка была🤣

Dirty job

Wow beatiful vary good 👍🏻💯💯

Gratis work to fix the mounting problem but he overlooked the heat crack on the Facebook

Another useless repair with the worst possible way of repairing that part. But at least you are making money on KZread.

piece of junk.time wasted on that job.

А потом на хаду как он разлетится и пизда индусу он лопнул в месте прилигания диска и шлифовать кго не льзя

а шо такое ? чугун ? уже не паяется ?

@Cepera03

Ай бұрын

Электороды после дождя отсырили.

Jejak Allah.qar.