E: "That's for like a a treasure chest dude" K: "Maybe it unlocks the secret to 3rd gear" BWAHAHA

@thatautogarage3644

4 жыл бұрын

VictorT_Media I literally read this comment as this part of the video was playing, 3rd Gearception

@MOTO809

4 жыл бұрын

I got a good solid laugh out of that.

@SteveLowe65

4 жыл бұрын

Came to the comments looking for this. 🤣

@shize9ine

4 жыл бұрын

E is the only person i've seen on YT money shift a sequential XD

@Timberwolf69

4 жыл бұрын

I was about to grab my glass for some hydration when this came. I don't know why I briefly heasitated doing it, but it saved me from spilling my drink all over my keyboard.

With all those parts on the back of the crank being misaligned, I’d pull the pan and check the thrust bearing in the motor while it’s all out. Just to be safe.

@horderelations4041

4 жыл бұрын

ABSOLUTELY! This needs a bump to the top comments!

@zaksuzuki

4 жыл бұрын

Check all bearings and probably bent the input shaft to

@jonasthemovie

4 жыл бұрын

Or slap it all together with the dovels and half of the bolts.

@Laminur

4 жыл бұрын

+1 this. Easy to do for the peace of mind.

@Snarf_Le_Wombat

4 жыл бұрын

Crank walk the dog like a 4g63

"If it's leaking there is still some in there" Spoken like a true motorhead.

@guildensteinfoutch6232

4 жыл бұрын

If its leaking oil. Its got oil lol. Seen that posted on a page the other day lmao.

@wesley8599

4 жыл бұрын

Honestly too true. Leaking oil is still oil

@_Professor_Oak

4 жыл бұрын

Just scoop it up with a cup and chuck it back in the engine, no point wasting good oil now

@johngonsoulin7413

4 жыл бұрын

A common saying with military helicopters too 😅

"I want to clean it up and finalize it later..". So its permanent, huh?

@PSNxFTWxRAGOI

4 жыл бұрын

$10 bet that its going to stay the same in a year lmao

@damiendoisher7812

4 жыл бұрын

We all know it lmao

@brotherhood_ofstreetracers4268

4 жыл бұрын

Binford2500 disappointing but yea.

@hybridEP3

4 жыл бұрын

Kyles a fking hack lol

@UCCLdIk6R5ECGtaGm7oqO-TQ

4 жыл бұрын

There are few things in life more permanent than a temporary solution.

Remember when you closed the engine to the transmision gap with the bolts? Probably busted pilot bushing then.

@whidden1998

4 жыл бұрын

Second this

@dsshowerpan

4 жыл бұрын

Thirded

@PSNxFTWxRAGOI

4 жыл бұрын

Forthdeded this

@rsharney1111

4 жыл бұрын

4th, saw that and knew they'd be back in there sooner than later

@gsppuffer

4 жыл бұрын

Without a doubt

At least these guys are consistent. The horse power matches the amount of times they pull the motor. lol

@dougn6465

4 жыл бұрын

Its apart of it at this power level

@The_Chosen_None_

4 жыл бұрын

@@dougn6465 Nah dude, everything they rush ends up breaking. That's the name of this game.

@russrtspooling7702

4 жыл бұрын

@@dougn6465 when you use a weak platform it happens regularly

@1991CALYPSO

4 жыл бұрын

Hack shit together and this is what you get.

@DeAndre_2000

4 жыл бұрын

russrt spooling what would you call a strong platform

I dont think all these things " come loose" ....they're just never tightened to begin with 😂

@gearedweird3682

4 жыл бұрын

No dowels definitely does that

@zaksuzuki

4 жыл бұрын

its classic boosted boiz, half done stuff never patient enough to finish before going for a rip or forgetting to tighten stuff up.

@stoker20

4 жыл бұрын

Little dab will dew ya.

@wilsoncrocker

4 жыл бұрын

theyre just posturing for that loc-tite sponsorship lol

@iNegroTv

4 жыл бұрын

@@zaksuzuki I don't blame them when everyone is screaming at them to get everything finished rapidly. Shit happens, but luckily for them they have the money and support to fix problems

Kyle: "Maybe it unlocks the secret to third gear..." Emilio: (laughing) "yeah well maybe if it does you'd be in luck!" LMFAOOO

@DjimiVidZ

4 жыл бұрын

😂😂😂

@ngcolby

4 жыл бұрын

Laughed, snorted, choked on my own spit...wife is looking at me funny now...

@djpickle68

4 жыл бұрын

Cracked up.....

When they said the van was leaking oil the first thing that came to mind was the oil filter. Remember who put the oil filter on

@bugboyaidan7733

4 жыл бұрын

TheManistheshit genius thinking my guy

@griffinmackenzie

4 жыл бұрын

🤣🤣🤣

@imalec

4 жыл бұрын

💨 💨 💨

@MrTheHillfolk

4 жыл бұрын

My buddy drove his Toyota pick up all spring and summer with a really bad oil leak. he had a 25 mile round trip and he would put in about 3 quarts of oil a day. So one day after getting tired of it he looked underneath. He realized he could not remember the last time he had the oil changed, and it must have been a long time because the oil leak was a hole rotted in the filter 🤣🤣

@benjaminharvey8617

4 жыл бұрын

@@MrTheHillfolk no one cares

Would be great for someone's build to actually have a steering wheel in the straight position while going straight

@SirVic42

4 жыл бұрын

Then how would he know which way to turn when doing a wheelie?

@armedziak

4 жыл бұрын

@@SirVic42 Some ducktape in the middle of the wheel would help

@tiddiesprinkles

4 жыл бұрын

Asking way too much

@backyardboostin9908

4 жыл бұрын

These guys a kings of not finishing builds

I have so much respect for the ole man at S1 build. He has forgot more about AWD than most will ever know.

@trainer093

4 жыл бұрын

He knows his shit, really smart guy

"If it's leaking oil that means it's still got oil in it." Good to go then lol

"Vicious coupler attacks Boosted Boiz while they try their hardest to acquire The Rona."

@SirVic42

4 жыл бұрын

TBH the Rowdyssey deserves a vicious coupler. Nothing tame about that build.

@Aschmorr

4 жыл бұрын

The Rowdessey is immune to the Rona’

Holy moly Kyle, that alignment is atrocious on the Rowdyssey! Get that wheel straight boi

@shedman7306

4 жыл бұрын

Are you new to the channel?

@jonasthemovie

4 жыл бұрын

That would demand them to actually loosen the tierod nuts, which means they will be forever loose.

Hang that special key from the mirror so you’ll never lose the pathway to 3rd gear 🤘🏼

HASTE LEADS TO WASTE!!! stop rushing stuff again lol. get max quality!

Can't believe you guys didn't have any dowels in there...I'm an amateur mechanic at best, and realized that was a pretty important aspect to my stuff going back together...You guys are playing with some pretty expensive parts to be cutting those kinds of corners, tighten up lol...Btw, I graduated from high school in June of '97...

Need to rename this channel to Halfassedboiz.

@unclej4997

4 жыл бұрын

Master Exploder there’s a reason Brent is always saying “the Boosted Boiz way” lol

@Prado805

4 жыл бұрын

Master Exploder Justin Colvin Foreal 🤣🤣🤣

@punisher8426

4 жыл бұрын

@Anonymous exactly

@slammysj

4 жыл бұрын

@Prado805 Lol

Way to make me feel old. When you said you were born in 96, that was a shocker. I was born in 81, I don't want to be an old man. Life goes quick and the older you get the quicker it seems that the years click away

That moment when I realize how young Kyle is, and how far he’s come up with his KZread career in such a short time... such an awesome accomplishment.

Oil pressure gauge: Saves car. Oil pressure sender: Brakes car.

@patriots001fan

4 жыл бұрын

Paul Jones breaks*

@pce0513

4 жыл бұрын

Spelling aside that's quite ironic.

@Timberwolf69

4 жыл бұрын

@@patriots001fan Well, in a way, it's both.

Dowel pins always install them! I learned the hard way with a customers car back when I worked at Nissan on a rogue

@cooperchurch8418

4 жыл бұрын

cannabased as a tech, you put things together fast and sometimes forget things. its happened to everyone. flat rate is ass

@89hybrid88

4 жыл бұрын

If this was the first time he did something in haste that would be one thing.

@_jay_376

4 жыл бұрын

@cannabased when you do a shit load of cvts and your flat rate sometimes you just forget it you swapped the dowel pins or not

@_jay_376

4 жыл бұрын

Now I keep extras in my tool box for any time you can’t get them out of the old trans from being seized/stuck in

Same ol kyle low oil pressure and missing gears 😂😂😂

Glad to hear you are adding oil pressure guages to your cars, I had the same problems back in the 90's with those brass "T's" , I made a distribution block out a chunk of aluminum, just drilled and tapped a " cross" with 2 small mounting holes on the edges so I could mount it on the fenderwell and run all my oil lines and senders to it. I think Summit makes one that's fancier but mine worked fine for what it was.

13K Views in half an hour . Cranking it . I tell everybody I meet to watch you guys .love your channel . Keep it reals bros

Always doing pulls when things are not ready or tightened down!! 🤦‍♂️🤣

@The10000lbGorilla

4 жыл бұрын

How else are you supposed to know what needs tightening?

@diannecrawford9996

4 жыл бұрын

@@The10000lbGorilla by tightening every bolt before you leave. Obvs🙃

@tannershanksftw

4 жыл бұрын

r/woosh

Definitely seems like an alignment issue but it seems like you guys have it figured out and on the right track again. You guys make me so proud honestly, you didn't let bs ruin your day you guys just brainstormed how you were gonna go about fixing it

Loved how you said "We have a sequential minivan" Kyle....best part of the video ....squad goals

I would just solid mount everything on Hondaru and remove all the variables from engine/drivetrain movement. It's already going full drag spec so may aswell do it.

@MartijnPeek

4 жыл бұрын

MafiaboysWorld solid mounts wouldn’t have prevented this though.

@harleydanforth5986

4 жыл бұрын

Anonymous even that wouldn’t work... it was the internals that we’re moving not the housings

Perfect timing my powers been out since 6 am and I can’t watch a boosted boiz without having a good laugh

@sPeCThaGod

4 жыл бұрын

SAMEEEE

@markwallace5274

4 жыл бұрын

jdm noob you live in the south ? Storms was tough last night

@dannym5106

4 жыл бұрын

NC?

@arturo762

4 жыл бұрын

R.I.P

@jerome7103

4 жыл бұрын

Chatt town?

Thank god y'all didn't blow up with low oil. Keep up the good work guy's and be safe, can't wait for the next videos.

With the rush schedule and so many bolts to keep up with it looks like a fun full time job. Keep on rippin

I have seen this before the dowels will most likely solve your problem I saw it in a sbc V8 swapped tractor It would not cause any issue sitting there I the clutch worked great but as soon as you put load on it the torque would cause the engine in my case to shift just slightly enough to make things hit The owner ignored it for one event it said boom and blew the bell housing apart

@Nathan-gj8ch

4 жыл бұрын

but why would anyone not run the dowels ?

@knowbull5hit590

4 жыл бұрын

Nathan Fitzer forget to put em in most likely lol

@zaksuzuki

4 жыл бұрын

@@Nathan-gj8ch because they couldnt find them, they re small and easily lost. Rather then wait til they had the dowels they said "sent it bruz" and forced the gearbox to the engine thinking all would be okay.

@dazaspc

4 жыл бұрын

100% no dowels the cause with high HP. You can see the movement on the mounting faces. I strongly recommend installing the bell housing and clocking it up with a dial indicator to ensure it is concentric with the end of the crankshaft.

@zaksuzuki

4 жыл бұрын

john maselli it’s all over KZread sometimes I swear they half ass shit just for content. Everyone keeps watching so why not.

Its like people in Florida don't understand what a lockdown and social distancing is. lol

@ronjones-6977

4 жыл бұрын

But they used hand sanitizer! lol Anyone shaking hands right now is just fucking stupid.

@hinds90

4 жыл бұрын

Same in Houston, Tx. It doesn't mean anything until it affects you personally.

@St1ngerGuy

4 жыл бұрын

Only a matter of time before these dudes get the Covid. The virus travels up to 13 ft in the air and it doesn't take much to get it. I'm in FL right now and people really aren't taking it seriously. Bright side, real estate prices are about to drop.

@BBROPHOTO

4 жыл бұрын

I think this every time I see these videos drop. Where I am, hospitals are having to choose between who lives and dies. Thousand and thousands of people have died here, where families cannot even say goodbye or attend their funerals. The blasé attitude is actually quite shocking and the fact they don't even make a serious mention in any of these videos is questionable.

@emeraldisle70

4 жыл бұрын

BBROPHOTO what city are you referring to that is so overwhelmed Dr’s are triaging who lives or dies?

Kyle man love your build.i watch all your videos.keeps me motivated.maybe one day I'll run in to u at. S1 .keep it up.an yall stay safe.

The keys open Industrial DB Boards good fine lol. Keep ripping guys. Tello all the way from SA

should check the input bearing in the transmission, with the pilot bearing worn like it is, the input bearing will take the abuse.

Even tho the shaft from the trans is new I would put a run out gauge on it to make sure its perfect.

I'm happy you guys went down to visit S1Built. Those guys are doing it B I G in the AWD scene.

Thank God she's good ! I'm excited about this build!

Kinda remember u guys having to draw the trans in using the bolts!!!back in a video before you left colorodo🤔

@mikesweet5848

4 жыл бұрын

Big upvote this is facts.

@iNubAlert

4 жыл бұрын

That's a relatively normal thing to do but it eventually aligns and goes easier into place

@xplore7359

4 жыл бұрын

@@iNubAlert not if the dowel pins are missing..

@shedman7306

4 жыл бұрын

@@iNubAlert dont know what kind of shop you worked in but mating the trans with the bolts is a big no no.

Co out young statics channel hes done a video on the awd pinning the rear and welding bro ..🤙🤙🤙🤘💪

Excellent video boys love from Colorado

great overall and love the outtro your vids are more complete.

Is the clutch disk in backwards?? I made that mistake before.

Have the clutch disks in the right orientation!

Kyle is definitely the king of half assed whether building a car or shifting gears

@nkill6

4 жыл бұрын

It's a Colorado thing we never take anything seriously

Kyle's got the right idea, I'd agree. That quick rip with the loose mounts probably bumped it a little and made your clutch self-clearance a little. Good thing you guys caught it before any serious damage. Shit happens, but as shit goes, this dont smell that bad! Keep at it Emilio, I wanna see Hondaru rip it!

If you twist a trans with no dowels and loose mounts, your probably going to need a new input shaft.

So close to a million subs, I’ve been here for a hot min apparently

I'm glad the van is good!! Look into the freelander driveshaft!

Proud of you bro! 3 bolts!

Piston rings broken in now 😂

Just going to throw this out there. I adapted a range rover driveshaft to fit my crv. I pinned the rear clutch pack to make it solid. Here is my old build thread on it and also here is a video of the rear working great. honda-tech.com/forums/honda-cr-v-element-156/new-me-cr-v-3091170/ Driveshaft stuff starts at post 145.

@JD-rq7il

4 жыл бұрын

kzread.info/dash/bejne/doqWuMSLn9Cqj9o.html

in Minnesota when the car leaks oil like that we just call that rust prevention lol

The key for unlock 3rd gear, hahahahahaaaa that's funny af kyle!

all she needs is some seafoam and she'll be rippin like new brother!

@GetBent520Az

4 жыл бұрын

Von Hassen lmao

@GetBent520Az

4 жыл бұрын

I did that with my del sol. And my friend said exactly what your comments says. It no longer runs now 😂

@TheVanderbone

4 жыл бұрын

RNE Productions just from seafoam or from something else? I’ve seen one or two comments saying seafoam messed up their motor, but I’ve also done it on three different old ass motors and have seen decent results. My experience obviously isn’t gonna be everyone’s experience but a little $12 can helped my throttle response a lot on an old V8 and an old 4 banger that would both stumble when you blip the throttle.

@sffabrications3872

4 жыл бұрын

Skyler dude you have to remember there’s people who think it’s the fix all and bad luck with it. I’ve never had a failure with sea foam. I love all their products.

@TheVanderbone

4 жыл бұрын

Fix N Fab Collision that’s true, it’s not a fix all, but unless you did something very wrong I don’t feel like seafoam would cause a catastrophic failure either you know? If the motor was already messed up in some way I’d understand but I personally just didn’t see how seafoam would cause a problem if it’s used right.

Seems like the input shaft on Hondaru's transmission isn't long enough.

@scooz14

4 жыл бұрын

Or the ID of the pilot bushing is larger the the od of the input shaft pilot

@charlesadkins3335

4 жыл бұрын

Could be maybe the shaft isn’t going thru all 3 disks

@rollerdragon

4 жыл бұрын

if the pilot bearing/bushing weren't seeing enough of the input shaft, would it have been bashed up like that? off center (i.e.: no dowels ) would cause the edge of the disks grinding and do that to the bushing, if the input shaft makes 1/2" of penetration, it will work... the shaft isn't tapered at the bushing... with dowels, and a clutch alignment tool, the plates can't hit out of round... loose mounts added and that shaft/bushing union is the weakest link. but thats just my two cents on it, we all have ideas of what it could be... hell, I'm just glad they're all healthy!

@scooz14

4 жыл бұрын

@@rollerdragon that's why I think that it has to be either alignment or mis sized. The way that bushing is beat up, it has to have some engagement with the input shaft.

@hupondio

4 жыл бұрын

I think they need to review the adapter plate

Could have cruise by my house here in Ocala Florida lol. That engine is good. 💯👍🏽👍🏽👍🏽

Damn you can hear Kyle was shitting bricks when oil pressure went low. I would have been bummed out too. Good catch though! 🙏🏻

Never seen a group of guys have so many issues all the time with Honda’s 🤷‍♂️

@iantowers6972

4 жыл бұрын

hybridEP3 cut too many corners bro you go round in circles fella.thats why they have issues all the time do it rite do it once!!!!👍🏻👍🏻🇬🇧👌🏻

@birdness

4 жыл бұрын

That's what happens when you start pushing big power.

@TakeNoShift

4 жыл бұрын

@@iantowers6972 Whats with the Union Jack?

@Matty.Hill_87

4 жыл бұрын

@@TakeNoShift my guess is he's from the UK 🤷‍♂️

@TakeNoShift

4 жыл бұрын

@@Matty.Hill_87 I thought that, but then what does that have to do with doing it once and doing it right? Sounds a bit prejudiced.

at 4:15 of this boosted boiz video kzread.info/dash/bejne/gq6MxquNet29Y7A.html you can see that the engine doesnt just mate up with the trans, Emilio says " im just gonna suck it in with this bolt" good rule of thumb is to NEVER draw rotating assemblies together with nuts or bolts. They should mate up flush and fastened once together

@otm646

4 жыл бұрын

Exactly. I'm absolutely flabbergasted they didn't use the dowel pins in that either.

@iantowers6972

4 жыл бұрын

They don't understand enough of how these things work properly that's why they are always redoing things etc .cut corners go round in circles!!!👍🏻😂

I just woke up and saw this video.. started watching it and kept falling a sleep😂😂

Love you guys and your builds!

Oh great! Now kyle cant even find 1st gear!

I like how the description is just “close call”

I think you are on the right track suggesting trans not in alignment with the crank centre line. Perhaps measure to see if the adapter plate lines up. good luck!

Emilio spots keys, Kyle " hopefully that's the key to 3rd gear!" 🤣 lucky spot there with the leaking oil too!

So much for quarantined. Driving around to different shops.

@bhew7409

4 жыл бұрын

no idea why the US got hit so hard...

Once boostedboiz post then everything else have to wait for a while.. have to watch....

The flywheel pilot bush is probably worn or bearing on gearbox side is knackered! Only way them plates could of touched the side of the pressure plate! Had it happen on one of my trucks with the pilot bush worn-the shaft wobbled about and the clutch plate done exactly what yours has!

Lol love that attitude "if its leaking oil it still has oil😂

He said they had the dowels, but they did not install them, right? So they put it together without dowels? Or am I misunderstanding?

@MartijnPeek

4 жыл бұрын

First Last they had dowels at one point, probably didn’t have them when assembling it this time. Because if they did have them that would’ve been stupid.

**VIRAL VIDEO** "STREET RACING PPL IN THE SLEEPER SOCCER MOM MINIVAN" (TOOK LAMBO TO GAPPLEBEES) 😂😂

Try to pull the clutch alignment tool in and out slightly while slowly torquing clutch plate bolts to flywheel. Should be able to be pulled in and out easily (with your finger tips) after clutch is torqued. Then make sure the input shaft is fully inserted into pilot bearing before hitting the bell housing bolts with ratchet or an impact. If the bell housing bolts are used to pull the trans to the adapter plate, the term “properly aligned” kind of goes out the window lol Love you guys and the content, not meant as a hate comment.

K-Tuned sells a short feed line adapter for the oil lines. Has the main port for the sensor and two ports to feed oil.

Perhaps because you're not running a bloody air filter. Good job you get given these turbos

@MattBerrymotorsport

4 жыл бұрын

I can't believe it either

@zaksuzuki

4 жыл бұрын

It’s the entire engine that will suffer. It’s the most simple thing but I don’t understand why they never put them on. They think it will rob them of half a hp?

@MattBerrymotorsport

4 жыл бұрын

@@zaksuzuki here's the funny thing, if you buy a pod filter that has a "bellmouth" inside the air filter you actually pick up HP by using one. That blue car in my DP is twin engine with identical combos front and rear, the rear engine has an air filter and makes 30 HP more. Take it off and the power drops lol go figure I stupidly designed the front turbo placement not to use an air filter before I rear about this and now I can't do anything about the power losses

@zaksuzuki

4 жыл бұрын

Matt Berry sounds like a mental project. Seems like a lot of these Honda guys don’t run filters because they’re always using turbos that are way to large for top end or just design they’re manifolds poorly. But when you can run one I don’t understand why you wouldn’t, no negatives to it.

@MattBerrymotorsport

4 жыл бұрын

@@zaksuzuki looks cool to see the wheel. That's about it

5:27 lucky man kyle can finally hit 3rd

@thirdgenfreak25

4 жыл бұрын

Before it was 1,2,..... Red line!!! Lol

@seanstubbs2620

4 жыл бұрын

we don't want to here no more money shifts round here that sounds expensive

Glad to see you caught it in time.

awsome. loving this channel atm

Receipt was printed the same day i was born!

@smooth_ops2942

4 жыл бұрын

Same day? If so you need to buy a oddesey 👍🏻

@Huda88754

4 жыл бұрын

My 9th birthday

5:31 unlok the secret to get in 3 💀💀💀

I think they right about something no being aligned and the pressure plate spinning around it got hit making sparks but I'd check out that conversion plate too to see if it's still on flush.

I think you'll be fine just putting the Hondaru back together as long as you install the dowel pins. That why the trans shifted over a bit. Even torquing the trans to engine bolts to spec without the dowels installed it's going to shift under power. The dowel pins aren't just to aid in installing the trans to the engine, they are there to keep them aligned. Good luck!

Wear your seatbelt emelio remember the golf cart.

You guys were pretty rough mating the engine to the transmission, you may have bent the input shaft.

@gsppuffer

4 жыл бұрын

Yeah used bolts to pull it together and them bushings are super weak

THE BUILDS love the channel/// but kyle i think you should put a Quick release in miss Rowdy ... i think it will make the inside pop, just by adding a black quick release steering wheel it would look so good , STAY SAFE GUYS !!.. oh and also i think you should also give the van a fresh coat of paint.. i know sleeper look.. BUT DAMn i think the van would loook so good with paint to

If the bellhousing separates from trans you could check the alignment with a dial bore gauge to make sure input shaft is centered

No dowel pins? Cmon. Dudes. Any cover u put on any case half’s any trans ANYthing like that u need dowel pins. Crucial.

Everyone be saying “stop rushing things, do it right”... it’s called content! If there were no problems it would be pretty boring.

@IvanGarcia-eu5un

4 жыл бұрын

griplimit can’t say it better myself

Maybe an extended length spigot bush to go with the adaptor sandwich plate? I take it that is what is on the back of the block to allow it to bolt up to the Subaru bell housing?

Instead of using a tee fitting or sandwich plate, why not use a vacuum distribution block as an oil distribution block? Vibrant makes a block with 6 1/8" NPT outlets and a 3/8 NPT inlet. You can run a single line to the oil block, mount your oil pressure sensor directly to the block (which also fixes your vibration issues and helps keep the sensor in tact), and run your turbo oil feed off of this block too. Looks a hell of a lot better than a sandwich plate, gets your sensor away from unnecessary vibrations, and gives you room to add an oil temp sensor further down the road without having to do anything other than pull a plug out of the block and screw the sensor in.

Lol. Says input shaft is brand new and it can’t be bent. I’ve seen lots of new stuff not be right.

@MrTheHillfolk

4 жыл бұрын

Yea but no dowels .... That is probably what did it , and it coulda bent the input shaft but it's probably 🤞ok

Oil line T fittings been killing turbo Honda's for years.

@rsharney1111

4 жыл бұрын

Dedicated lines only

@The10000lbGorilla

4 жыл бұрын

@@rsharney1111 do you not run an oil pressure sensor? Or do you get oil feed elsewhere?

@antonop100

4 жыл бұрын

This is the correct way www.theoldone.com/articles/oilpressure/

im not too sure how that flywheel will be but i guess you guys will find out, or already have lol lucky with the minivan too for sure!

Sweet as....well done lads.

Hey bro I got a vc off a land rover I’m down to send y’all just pay for the shipping it’s the whole complete driveshaft

@lijahmack111

4 жыл бұрын

Reggie Sanchez send it to me instead lol built h2b turbo crv

@southwestdesertfrenchies

4 жыл бұрын

Lol I have a B20v turbo crv full build that’s why i have 2 of them and if I send you you it will not be free for them it will for the build and to support them

Your right Kyle 👍pins are definitely needed 😎remember you have to pin it to win it 🏁🚗💨💨💨💨💨

Hondadru could have a mispaced input shaft that would cause it to waller around in the flywheel. Sometimes I have to shim new shafts in old t56 cases . not sure of the design you are working with , but its worth measuring the up and down play on the shaft.

The dude from S1 Builds seem like the coolest guy ever!