I bought the J-B waterweld yesterday. Your video just gave me the confidence to go out there and fix my Rubbermaid cattle troughs. Thank you buddy great video

I appreciate all your videos man. Just found your channel and I’m running through all your freezer cold plunge tips. Getting my freezer delivered within a few days now and I’m definitely going to be implementing your methods.

I'm the last part of that were you used a wet paper towel you know you can get like a small cup of water dipping your finger in it keeping your finger wet and run across there and get a better finish than that paper towel would ever do just like you would do if you was running a bead of caulking

Damn. And I thought I was a perfectionist lol Very fine work

@Frodoswaggns

Жыл бұрын

Yeah those lines look clean compared to my icebath.

“Right when I’m finished I’ll be done” Priceless 😁

@APEX.86

Жыл бұрын

😂

did you purchase an adapter that attaches to drain plug which then you can screw a hose into to drain out the garage? do you have a link to this adapter

@APEX.86

2 жыл бұрын

I actually designed and 3D printed one. The trouble is, the hose size is so small it would take an eternity to drain. I drain via a much larger hose, syphoning, then pour the last bits out of the drain. You could just use a towel at that point though.

Did you use any pond shield or waterproofing layer after water welding? Thanks?

@APEX.86

Жыл бұрын

I have not yet. The factory enamel is still holding up. If it ever fails I can coat it then.

Man:/ i just bought 5 of the epoxy tubes that come in the syringe that mix upon application, is this okay too?

@ryanbellus2831

7 ай бұрын

I’ve been looking to see who out there has tried the marine weld you’re speaking of… I’d love to know how that turned out?!

Do you have any tips on sanding before applying the JB epoxy?

@APEX.86

Жыл бұрын

I would apply masking tape first and sand only the area to be JBWW'd. You want a light scuff of very coarse sand paper.

@Madgjk

Жыл бұрын

@@APEX.86 Right on. Do you sand in a circular motion or up & down or side to side? It's my first time sanding & I think I will be doing it by hand so I don't want to mess up

@APEX.86

Жыл бұрын

@@Madgjk I wouldn't worry too much about that. If every area has some cross hatching, you are good to go. Worry more about cleaning before application. Use acetone and do multiple passes. You want it reallllllly clean.

@Madgjk

Жыл бұрын

@@APEX.86 Ok right on! Thanks for all the replies! I figured I was over thinking it per usual lol. I purchased acetone as well. So should I apply the acetone as I go along right after sanding an area or wait til I completely finish sanding the entire freezer to then apply the acetone?

@APEX.86

Жыл бұрын

@@Madgjk acetone all at once before JBWW

I am buying a 14 cubic ft freezer...any ballpark guess of how many of these 2oz JBWW's I should buy?

@APEX.86

6 ай бұрын

If you buy from Amazon, you can get extra and return what you don't use. The width and thickness of your beads have a huge impact on the amount used. It could be 6 tubes, it could be 16.

Fantastic job on sealing with JB WaterWeld and thanks for this very helpful video. Wet paper towel at the end is a great touch. Looks like you were not wetting your gloves with water throughout application process and it didn't stick to your gloves much. In my case, wetting my hands was helpful but now I see that just as John Richter said, it's possible without wetting hands. Were you using Vinyl, Nitrile or Latex gloves and did you have to change gloves with each 2 oz tube of water weld? Thanks again for this video!

@OhCrapItsJimmy

2 жыл бұрын

Man I have this same problem w/ it sticking to my gloves. Half the stuff ends up stuck on the gloves. I'll try the wetting tip because the 'sticking to the gloves' is a real problem for me.

@Bravadosjebsimbahsm

6 ай бұрын

Are gloves necessary?

How many tubes?

@APEX.86

2 жыл бұрын

7 total

@puckeater1

Жыл бұрын

​@APEX.86 thanks for asking 😊

What kind of gloves are you using?

@APEX.86

Жыл бұрын

Just normal latex gloves.

@lujon103

Жыл бұрын

@@APEX.86 I appreciate the response. I bought the waterweld epoxy putty from JB Weld because it's food and beverage safe. I need it to fix my dogs water container. You're mixing it by doing the snake technique is very helpful advice.

Will it stick to silicone?

@APEX.86

2 жыл бұрын

No remove all silicone first

@farnjokerehis1724

2 жыл бұрын

@@APEX.86 cheers. It’s too late I’m Making an ice bath out of freezer and I made the mistake of wanting to silicone first and then waterweld for extra protection. Will it just not stick hey?

Did you seal the drain hole?

@APEX.86

2 жыл бұрын

I sealed the seam around the drain, but left it functional.

@jkinder3379

2 жыл бұрын

@@APEX.86 nice. I think I’ll try that. I have the Frigidaire which it looks like you do to. Did u leave the plug in and just carefully work around it?

@APEX.86

2 жыл бұрын

@@jkinder3379 I think that is what I did. Then immediately removed the plug to make sure it was wiped clean.

@jkinder3379

2 жыл бұрын

@@APEX.86 seems like the plug might have a really slow leak. Did you use a gasket with plug or tephlon tape?

@APEX.86

2 жыл бұрын

@@jkinder3379 I found an o-ring that fit on each plug nicely. Then I tested them individually and both sealed.