The old pump had bad seals so we installed a new one.
Жүктеу.....
Пікірлер: 21
@randywl8925 Жыл бұрын
How to install a water pump..... ...remove from box, paint it, then skip the installation and show the pump installed 👍
@BAGOTCORNER9 жыл бұрын
Good Video Buddy ! Glad I wasn't an amateur on that one ,,seen my fair share of seal failure indicator holes :) Cheers buddy
@UnitCrane5149 жыл бұрын
Looks like a solid fix!
@willt91729 жыл бұрын
Good job, love the Vette.
@motoforlyfe
9 жыл бұрын
Thanks Will!
@krazy45cat9 жыл бұрын
Nice Job Buddy !!!
@motoforlyfe
9 жыл бұрын
Thanks buddy!
@ziggassedup9 жыл бұрын
Job done.
@steveskouson96208 жыл бұрын
Did you check the tightness of the bolts on the rear cover? I didn't, on a car a few weeks ago, and the pump came back off. Yes, the boss tore a strip of skin off of me, AND the supplier! Buy a water pump, and the manufacturer DIDN'T assemble it correctly! Those bolts were finger tight! Now, I ALWAYS check. steve
@motoforlyfe
8 жыл бұрын
+Steve Skouson Thanks for the tip Steve. Probably a good idea to make sure that they are tightened!
@MalcOfLincoln9 жыл бұрын
Good job :) Bet you love working on these old cars...better than changing the pump on your truck eh!
@mattbartolovich8228
3 жыл бұрын
I'd do older ones anyday!
@jayborn26102 жыл бұрын
MSSED A LOT. XAMPLE? SERPENTINE BELT........OHHHHHH YEAHHHHHH........
@m3talc0re5 жыл бұрын
Your accent confuses the hell out of me. It sounds like a mix of Boston, southern and Australian 0_o
@coolrides9 жыл бұрын
Nice how-to video! Did you have to use any gasket sealer on the gasket? :) Jack
@motoforlyfe
9 жыл бұрын
Yeah we put some permatex on it Jack!
@TheJhaley125 жыл бұрын
PLEASE ANSWER THIS QUESTION. The plug your talking about having to take out, isn't that the bypass hole? I got a new water pump and was told I had to hook that up to my heater hose which didn't make sense but now that I have I have no heater at all and I was just out over $200 getting my heater fixed and working great. I am desperate please help me with hooking that up THE RIGHT WAY. Thank you.
@alfredolira1082
3 жыл бұрын
Not sure if you solved it already but that plug is for your hearter core. Connect a hose from that plug to the Driver side of the heater core. Side closest to driver. That engine coolant circulates through tje heater core. When hitting the heater should open a flap to the heater core an send a signal to your heater motor to turn on and spin cause the now hot air to be pushed inside the cab
@jbmbanter9 жыл бұрын
With the hood raising forward I couldn't figure out what the vehicle was so what is it? :)
@Fritsvrolijk7 жыл бұрын
whats the outlet from the waterpomp asking for lpg installation thanks
@motoforlyfe
7 жыл бұрын
Are you looking for an outlet in terms of flow in gpm or similar units? Unfortunately I don't have that information.
Пікірлер: 21
How to install a water pump..... ...remove from box, paint it, then skip the installation and show the pump installed 👍
Good Video Buddy ! Glad I wasn't an amateur on that one ,,seen my fair share of seal failure indicator holes :) Cheers buddy
Looks like a solid fix!
Good job, love the Vette.
@motoforlyfe
9 жыл бұрын
Thanks Will!
Nice Job Buddy !!!
@motoforlyfe
9 жыл бұрын
Thanks buddy!
Job done.
Did you check the tightness of the bolts on the rear cover? I didn't, on a car a few weeks ago, and the pump came back off. Yes, the boss tore a strip of skin off of me, AND the supplier! Buy a water pump, and the manufacturer DIDN'T assemble it correctly! Those bolts were finger tight! Now, I ALWAYS check. steve
@motoforlyfe
8 жыл бұрын
+Steve Skouson Thanks for the tip Steve. Probably a good idea to make sure that they are tightened!
Good job :) Bet you love working on these old cars...better than changing the pump on your truck eh!
@mattbartolovich8228
3 жыл бұрын
I'd do older ones anyday!
MSSED A LOT. XAMPLE? SERPENTINE BELT........OHHHHHH YEAHHHHHH........
Your accent confuses the hell out of me. It sounds like a mix of Boston, southern and Australian 0_o
Nice how-to video! Did you have to use any gasket sealer on the gasket? :) Jack
@motoforlyfe
9 жыл бұрын
Yeah we put some permatex on it Jack!
PLEASE ANSWER THIS QUESTION. The plug your talking about having to take out, isn't that the bypass hole? I got a new water pump and was told I had to hook that up to my heater hose which didn't make sense but now that I have I have no heater at all and I was just out over $200 getting my heater fixed and working great. I am desperate please help me with hooking that up THE RIGHT WAY. Thank you.
@alfredolira1082
3 жыл бұрын
Not sure if you solved it already but that plug is for your hearter core. Connect a hose from that plug to the Driver side of the heater core. Side closest to driver. That engine coolant circulates through tje heater core. When hitting the heater should open a flap to the heater core an send a signal to your heater motor to turn on and spin cause the now hot air to be pushed inside the cab
With the hood raising forward I couldn't figure out what the vehicle was so what is it? :)
whats the outlet from the waterpomp asking for lpg installation thanks
@motoforlyfe
7 жыл бұрын
Are you looking for an outlet in terms of flow in gpm or similar units? Unfortunately I don't have that information.