Please remember the water pump is driven by the balance shaft chain and not the timing chain. People get them mixed up alot. Also I would install the tool upside down to the way you have it to prevent the bolts from falling into the engine.

@1020autorebuild

Жыл бұрын

Both those are great points, but turning the tool up side down is genius👍👍 I never thought about that to stop the bolts from potentially falling in the engine👍👍👍

@Nic1Moreno

Жыл бұрын

The tool is adjustable to prevent the bolts falling into engine , thats why you see the tool with slots

@300bhp

9 ай бұрын

Is the water pump beeing lubricated by the engine oil?

@gav3379

9 ай бұрын

Water pump bearing are sealed so no lubrication is necessary. However the sprocket enters the timing case which is lubricated with the oil nozzle. If the pump seal fails it could allow coolant to mix with the oil.

@300bhp

9 ай бұрын

​@@gav3379aha ok thanks. I thought it was lubricated by the engine oil and thats why they last a long time as mine has 200,000km and factory water pump

Idk why the comments seem aggressive. Good job i like you’re way of thinking. Maybe if you have to do it again in the future do a PART 2 inside the car. Great video i like your professionalism

I appreciate you taking the time to comment, and you definitely do not have to remove the engine to replace the water pump. I said in the beginning of the video and that it was just impossible to film the replacement of the water pump I was replacing so I was going to demonstrate on the engine I had removed already to show the procedure I use.

Great video! I am replacing a pump in an '07 HHR this week and after watching this I'm sure that I will get it done. I already bought the o-rings, those have to be ordered.

@1020autorebuild

5 ай бұрын

Thank you, I appreciate it 👍👍

Thank alot I watched a few videos of this job in you was the best one because you took your time in explain everything step by step in you gave me the hope to do one in thanks again

@1020autorebuild

3 ай бұрын

Glad it helped 👍👍

NOW I CAN SEE Thank a lot 👏👏👏

like the material men ..really clear tx..suscribed

@1020autorebuild

4 ай бұрын

Thank you, I appreciate it 👍👍

What is that big nut on top of the water pump like a drain plug

Wow,that's with the engine out.T.Y.😮

The gasket on the thermostat housing with the 10mm bolts is bad on my cobalt but I can’t find a part number. Do you happen to have a part number just for the gasket?

What year and how many miles when it was done.

I'm not judging at all making that clear, why is the tarp that protects the engine from oxidizing on the bottom of the motor instead of rapped around it. Just curious love the vid.

@k24oreo84

11 ай бұрын

Maybe he is protecting the table he is working on, think out side your box.

👍🏾

Hi, Is that the same procedure for a 2007 G5? I've replaced fan radiator and thermostat, and it still over heard while driving. Expect when I have the defroster on. Al the while and so far no leaks.? May someone help.im poor and broke and need car to work.

@1020autorebuild

5 ай бұрын

Exactly the same procedure 👍

Buy some cordless tools son.🙄It's 2023-24 😄

Not much of a mechanic I did it with the engine still in the car and I didn't take off the down pipe or the exhaust manifold Yes it can be done taking the engine out is a waste of time

@1020autorebuild

Жыл бұрын

I appreciate the comment, but I mentioned in the beginning of the video that it was hard to film the one I was replacing inside the vehicle so I was going to demonstrate the procedure on an engine I removed from another project You definitely do not have to remove the engine to replace the water pump ever

So you have to remove engine? God dam GM.

@1020autorebuild

7 ай бұрын

You do not have to remove the engine to replace the water pump I was just demonstrating how it was done on an engine I already had out of the car. When I did the water pump on the car that needed it it was almost impossible to film 👍