I just want to extend my sincere gratitude all the way from Atlanta Georgia i'm a husband and father of 3 and this video just saved me about $600 Thank You Sir

@TightWadDIY

5 ай бұрын

You are so welcome! We are practically neighbors! Haha.

MY Kenmore 90 series HD, stopped spinning, you could hear the motor working. Luckily I had a small wash, the water was drained, Wrung out the clothes, hung them up and found your video. I ordered the part on amazon for next day delivery, 3 couplers for 19$ CAD tax in. Then I followed your instructions. Never knew the casing could come off so easy. Removed the pump, i lifted the washer about 6 inches. Didn't need to undo the hoses, just turned the water off. Removed the motor (2 screws) pulled it out and the coupler was broken in two. Took me about 30 minutes. Thank you, this was so easy!! And I am a woman.. had this washer for 23 years and this is the first time I have ever repaired it. Tomorrow when the coupler comes in, I'll install it and come back to finish this comment. :) Got the coupler, installed it, my washer now spins perfectly!!! Thank you so much, saved me $$$$$$$$!!!!!

@TightWadDIY

7 ай бұрын

This made me smile big time! I’m so happy to hear you got it fixed.

Thought for sure the motor was shot on my washer, but it turned out to be just a little $8 part. I've fixed a bunch of dryers before, but never washers, 'cause I assumed they were far more complex. Turns out, they're just as simple, but I wouldn't have known that without seeing this video first. Good angles, well lit, and you even explained the sizes of tools needed. Thanks for the time and effort you put into this!

@TightWadDIY

8 ай бұрын

I really appreciate the kind comment and the gift. Most of all, I’m glad you were able to get the washer working again.

Thank you so much! Like others, saved me hundreds with an $8 part and very clear instructions.

@TightWadDIY

5 ай бұрын

Glad it helped!

Thanks! 70 series Kenmore is alive again. Very easy project didn’t even bother to lay it down. Just shell off and get down and dirty. My coupler only had 1 tooth left and years of burned up plastic bits 😂

@TightWadDIY

3 ай бұрын

Yes! I’m glad it worked for you too.

Thanks a lot - now it works! Saved me almost $400

After watching your video, I knew this was the problem with my Kenmore 90 series washer. I drove to a local parts store and bought the motor coupler; same one in your video. I’ve tackled other appliance repairs but never one on a washer. It was unclear to me which way to turn the washer over according to your video so I didn’t turn it at all. I googled this and it was recommended not to turn it on it’s back; only the front or side but I didn’t see how this would help so I left it. I think this made the repair extra hard. Getting the new coupler on and flush was harder than I anticipated but I finally did it. Anyway, a few hours later and it’s done. I cleaned up the innards of the housing while I was there. While this was harder than I anticipated, I’m glad I saved the repair charges as I know they would have been outrageous. Thanks for the video instructions.

@TightWadDIY

6 ай бұрын

Glad to hear you got it fixed!

@christys5857

3 ай бұрын

I have the same washer, and as soon as I heard the noise, I was positive that was the problem. Got the parts, and I'll be attempting this, too. Thank you for the clear video!

@TightWadDIY

3 ай бұрын

@@christys5857 I’m glad you found the video! Hopefully you can get yours fixed!

Thanks for the video, this was the exact problem I had with my washer.

@TightWadDIY

3 жыл бұрын

You are welcome. I’m glad it worked for you too.

Worked great. Saved me lots of money. THANKS!

THANK YOU for the great thorough video!! I did this once before, but it's been a few years ... and I'm pretty sure it's worn out again! Your video was very helpful!

@TightWadDIY

3 ай бұрын

Glad it was helpful!

Not only are u a money saver you walked us thru it all and I fix my own washer thanks to you

@TightWadDIY

4 ай бұрын

I’m glad you found it helpful

@mariagmedina23

4 ай бұрын

Thank you

Great instructions. Was able to fix my problem. First thought it was the sock in the pump, it was the black connection between the the two .

@TightWadDIY

2 жыл бұрын

I’m glad you were able to get it fixed!

@dioncurtiscurtis3188

Жыл бұрын

My coupler was cracked just like that when I took the motor off

about to do this exact repair for the 80 series i have, thanks for a good clear video.

@TightWadDIY

6 ай бұрын

My pleasure!

Great job of describing the steps to repair!

@TightWadDIY

5 жыл бұрын

SnapperKC Thanks! I try my best to be detailed but not too long winded.

Fixed my problem! Thanks!

@TightWadDIY

2 жыл бұрын

That’s great! I’m glad it’s working again!

Super super instructions you save my money and time. Thank you so much !!

@TightWadDIY

2 ай бұрын

Glad it helped!

Hey, this may be the best instructional video I have seen. Just did exactly what this video states and it could not have been easier! And, It works! Thanks!

@TightWadDIY

3 ай бұрын

That’s great! I’m glad you found it easy to follow!

@josephamirato9648

3 ай бұрын

@@TightWadDIY Great name! Just noticed, Lol

@TightWadDIY

3 ай бұрын

@@josephamirato9648 Haha. Make every dollar count!

Very nicely done

@TightWadDIY

Ай бұрын

Thank you!

I actually overpassed the lid switch and clipped the switch wire and put electrical tape on the wire and it worked fine. Probably not a good idea to do that instead of buying an new switch but it helped

@TightWadDIY

4 ай бұрын

That’s what I previously did.

good job! Thanks

@TightWadDIY

2 жыл бұрын

You’re welcome!

Great video!👍🏾

@TightWadDIY

6 ай бұрын

Glad you liked it!

Thank you!

@TightWadDIY

Жыл бұрын

You’re welcome!

Thank you sir!

@TightWadDIY

3 жыл бұрын

You are most welcome!

I got one Hotpoint htwp1400f2ww it gets to last spin and wont stop spinning with me moving timer to off. Only stops by opening lid or unplugging. Tried resetting motor same result. I also get a lound arc when plugging it in and squealing when spinning . Appreciate your post.

awesome video, much appreciated

@TightWadDIY

4 ай бұрын

Glad you liked it!

Thanks!!

@TightWadDIY

2 жыл бұрын

My pleasure!

Thanks!

@TightWadDIY

5 ай бұрын

Wow! Thank you so much! I truly appreciate it.

Awesome baby👍👍👍👏👏👏

@TightWadDIY

9 ай бұрын

My pleasure.

This was great. Thanks for sharing. Unfortunately, this was not the issue for me. Do you think it’s the motor or some other part???

@TightWadDIY

Жыл бұрын

It could be the agitator on the bottom.

great video…would this solution apply to a washer with a weak spin cycle? it will spin on light loads but not heavy ones. i believe it’s a direct drive washer just like this one so that would rule out a belt issue.

@TightWadDIY

5 ай бұрын

Im really not sure. That definitely sounds more like a belt issue.

Great video, I had the same exact problem, since I replaced the coupling now the washing machine stops a little more violently than it should. Any ideas?

@TightWadDIY

2 жыл бұрын

Interesting. Maybe it is finally stopping how it should?

@Struttinhoyt88

2 жыл бұрын

@@TightWadDIY maybe so, it seems to run and sound perfectly fine. But when it stops even with nothing in it then it shakes and and slams into the side of the case harder than I think it should. I’ve got a load of towels in it at the moment, I’ll watch and see what it does now.

Kenmore whirlpool 110 series. It looks like that on the insides. Sometimes, Maybe 1 out 15 times... When it gets to spin cycle and only drains the water but doesn't spin. At that point I just rotate drum a little and go back to spin cycle and it works. I've already replaced the control unit dial, the motor with coupler and capacitor. These are all genuine oem replacement parts. The washer is about 20 years old. Any ideas what else would cause this?

@TightWadDIY

2 ай бұрын

Sorry I’m really not sure what could cause that.

Sounds cut and dry as far as working on a machine my problem is that my 70 series agitates no issues switch seems fine but doesn’t always spin it has no rhyme or reason. I haven’t taken it apart yet figured I would see if you have any ideas thank you for your time

@TightWadDIY

2 жыл бұрын

Have you tried the other cycles to see if your cycle has an issue.

Hello, I followed your instructions and my washing machine spin well, but I smell a strong burning rubber odor and smoke came out. Do you know what it could be? thanks :)

@TightWadDIY

Жыл бұрын

Yours could be a belt drive and it’s going bad.

Is there a way to test the lid switch before taking the washer apart?

@TightWadDIY

Жыл бұрын

Not really. Usually you can visually see the switch is broken.

Hello, mine is the same washing machine. May I ask why the water won’t stop and the water won’t drain out when I choose the large laundry mode?

@TightWadDIY

Жыл бұрын

What do you mean the water won’t stop?

I could use your help. I have a Kenmore Model 110.24922200 90 Series washer. After completing one load of wash I started a second. The tub filled with water, agitated then stopped. No matter what setting I put it in nothing happens other then the water will fill. No humming, nothing. I did check the lid switch, it is good, I even jumped it to make sure. I also replaced the timer. I tried tracing the wires but got lost. Thank you in advance for any help. ..👍# 570 Stay well, Joe Z

@TightWadDIY

8 ай бұрын

Did you check the pump?

@JOEZEP54

8 ай бұрын

Thank you for replying. Yes nothing stuck in it.@@TightWadDIY

Have an 80 series and I installed a new coupler ,new clutch, new doggits . Wash and drains perfect except when time to wrung the clothes it wouldn't. I took some of the wetter clothes out and it started. Any ideas on how to fix this problem?

@TightWadDIY

7 ай бұрын

Have you removed the cabinet to make sure the belt is intact if it has one. If it has a coupler I wouldn’t t think it’s bad if it agitates but I guess it could be.does it hum?

Mine doesn't have a hole showing the lid switch. It works fine until spin cycle except drum always leans forward. When time to spin, I have to turn the machine off and then back on and then it will spin. It's a roper and I can lift the lid during the spin cycle, and noticed because the drum is forward water misses the drum sometimes but the spinning makes it fall into drum. Can the 2 be connected? Can't find a video to help me. Any thoughts? Ty for great videos!

@TightWadDIY

5 ай бұрын

Sorry it sounds like you have other issues if the drum won’t stay centered. Take the cover off and check the mounts on the bottom.

Hello , I have a speed queen top loader Nod. AWN43R+ that won't spin .can you tell me where to start looking other than checking the lid switch . I don't know transmission coupler are the same . Thanks

@TightWadDIY

4 ай бұрын

Sorry, I’ve never worked on a Speed Queen.

So mine still agitates but when it gets to the spin cycle it won’t spin I’ve tried in different settings / cycles but each time it just stops at the spin any ideas or tips for that also do you recommend a good place for parts

@carter4lyfe

Жыл бұрын

That's the problem I'm having...

@TightWadDIY

Жыл бұрын

It could be a broken belt, unbalanced load, or faulty spin switch. I’d start by checking the belt.

Mine keeps breaking thf coupler. What would be causing the coupler keep breaking?

@TightWadDIY

5 ай бұрын

Sorry I’m really not sure.

You skipped videoing at 5:19 the connector removal.

Can you please tell me your model #.I bought mine feb 2020 used not thinking to look for a model # for ordering parts in the future. Well the future is here and i need coupler. My washer looks exactly like yours . Thank you

@TightWadDIY

19 сағат бұрын

I think it’s a 70 series. I’m not sure about the model number.

Is this a direct drive or VMW?

@TightWadDIY

3 жыл бұрын

It’s a direct drive.

I got all the way to testing the washer by using the piece of wire to bypass the lid switch. When I try plugging in the washer to outlet, it sparks and trips the breaker. Any ideas?

@TightWadDIY

8 ай бұрын

Sorry I’m not positive.

Was yours making a grinding sound, mine still agitates but won’t spin in the spin cycle

@TightWadDIY

3 жыл бұрын

Try to unplug the washer for a full minute. Plug it back in then open and close the lid six times. If that doesn’t work, check to see if your belt is still in place.

@TightWadDIY

3 жыл бұрын

The grinding sign could mean your belt is off though. Not sure.

I've got this exact washer, and it's not spinning, but it's neither of these problems. I seem to have a belt on the bottom that is loose, but it's not connected to anything....

@jimmieblackmon7993

5 ай бұрын

Did you find out the problem, I have the same problem right now

I don't see the video to temp. bypass the lid switch? Can you direct me to it? Thanks

@TightWadDIY

11 ай бұрын

Here you go: kzread.info/dash/bejne/hJujraqeerupkps.html

What if it doesn't spin and the lid switch is bypassed and still doesn't work it does agitate which tells me the motor coupling is working but it won't spin there is a humming noise and a smell

@TightWadDIY

2 жыл бұрын

I’m really not sure.

Yoda A Man 🦍

My washer will not go into a high spin,coupler,cluth and dogs have been replaced, clothes are wet at end of cycle

@TightWadDIY

3 ай бұрын

Sorry. Could possibly be your timer switch.

Mine has a hard time spinning, I have to get the tub moving with my hand then it will spin

@TightWadDIY

5 ай бұрын

If yours is a belt drive it’s probably time for a new belt.

Motor coupling not broke replace last year. What next

@TightWadDIY

5 ай бұрын

Lid switch?

I know it doesn't matter, but ... I could never put it all back together without cleaning it first!

@TightWadDIY

3 ай бұрын

Haha. Get it scrubbed up!

Says we need a new panel

@TightWadDIY

2 жыл бұрын

Who says that?

You neglected to clean under the control panel while reassembling it, your wife gonna be mad with you!

@TightWadDIY

2 жыл бұрын

She will live! I do the laundry.

Thanks!

@TightWadDIY

9 ай бұрын

Wow! Thank you so much! I'm glad you found the video helpful.