No video

Walker Lawn Mower Repair - Blower Housing Replacement!

Step by step process on how to replace your Walker T25i (and older models) mower blower housing. This videos shows how I have replaced many of these bower housing. The process is very similar to the Exmark navigator lawnmower with hopper and deck blower. Email us anytime at jasonandjoniebuilds@gmail.com

Пікірлер: 88

  • @DavidSmith-ee5le
    @DavidSmith-ee5leАй бұрын

    Great job. We used this video & replaced our impeller in a little over an hour!!!

  • @JasonJonieBuilds

    @JasonJonieBuilds

    Ай бұрын

    Thanks for watching!

  • @marcuswilcox1486
    @marcuswilcox14862 жыл бұрын

    Thank you for this video. A couple tweaks on what you shared. I had a 3rd bolt holding the top of blower in place. If was horizontal and integrated with the bolts that hold the blower case itself together. I couldn't figure out why it wouldn't come out! Also, after taking the deck off, I drove it forward onto car ramps. Then took a jack and lifted the rear up onto a block of wood. Lifted the entire mower up and seems a bit more stable than tipping it over with a single jack stand. Thanks for making this, there is a reason you have 15,000+ views! Take care.

  • @JasonJonieBuilds

    @JasonJonieBuilds

    2 жыл бұрын

    Thanks Marcus!

  • @terrymizon6663
    @terrymizon6663 Жыл бұрын

    Omg am I thankful I found this video, thanks for posting it, one of my employees destroyed the housing today on my mower and this is one thing I’ve yet to repair on it so this was immensely helpful👍

  • @JasonJonieBuilds

    @JasonJonieBuilds

    Жыл бұрын

    I am glad to help. Thanks for watching!

  • @philliphall5198
    @philliphall5198 Жыл бұрын

    Thank You for information and advice Good to know how from someone who knows what there doing 😊

  • @JasonJonieBuilds

    @JasonJonieBuilds

    Жыл бұрын

    Glad to help! Thanks for watching!

  • @ibetdaniel1414
    @ibetdaniel14143 жыл бұрын

    Reach under and use the drive line release instead of just pulling drive line in half when pulling deck off. Makes it much easier to put back together.

  • @StephenBrewer89

    @StephenBrewer89

    3 жыл бұрын

    Thanks for this!

  • @markperkins5664
    @markperkins56643 жыл бұрын

    You have produced the best video I’ve seen on this task. Thank you. I’m replacing my blower next week. It has a very long crack that has worn longer and longer. Debris is now filling the engine area. It’s due.

  • @JasonJonieBuilds

    @JasonJonieBuilds

    3 жыл бұрын

    Thanks! Glad I could help. Good luck on the replacement.

  • @valleyoutdoordesign7308
    @valleyoutdoordesign73082 жыл бұрын

    Really nice job, its just like you said, not the worst job but a little time consuming. Thank you!

  • @JasonJonieBuilds

    @JasonJonieBuilds

    2 жыл бұрын

    Thanks!

  • @bayouslots3143
    @bayouslots31433 жыл бұрын

    Thank You, I need to change mine. Sent it to the shop the last time but this will save me money.

  • @JasonJonieBuilds

    @JasonJonieBuilds

    3 жыл бұрын

    It is a little tedious but not that bad of a job. Good Luck!

  • @bayouslots3143

    @bayouslots3143

    3 жыл бұрын

    @@JasonJonieBuilds I'm on my 3rd one. I do the same thing weld a plate to get a little more life, about another year after the first hole shows up. BTW did you ever change a hydro?

  • @JasonJonieBuilds

    @JasonJonieBuilds

    3 жыл бұрын

    @bayou slots No sir not on a Walker. I have done about everything thing else on them. They seemed to be pretty durable to me.

  • @mikecooley3361
    @mikecooley33613 жыл бұрын

    Y’all need to adjust the stop limiters on the deck arms. When you flip the release levers, they should glide in and out of the carrier without having to lift up and down on the deck to align the levers. It’s easy and takes less than 5 mins. There is an Allen bolt just below the release on each side with a jam nut. Loosen the jam nut and adjust the Allen until the arms move in and out freely, once adjusted, tighten the jam back up. Makes things so much easier when you have to flip the deck up. Thanks for the video, I’ll be tackling this soon on mine.

  • @JasonJonieBuilds

    @JasonJonieBuilds

    3 жыл бұрын

    Thanks man, I appreciate the advice. I'll keep that in mind next time I have his mower in the shop. Thanks for watching!

  • @mikecooley3361

    @mikecooley3361

    2 жыл бұрын

    @@JasonJonieBuilds I still haven't tackled it yet but i need to, especially since the leaves are starting to fall pretty good here in west Tn. Came back and watched it again just because I enjoyed it so much! Is that the standard 10" blower or the upgraded, bigger one?

  • @JasonJonieBuilds

    @JasonJonieBuilds

    2 жыл бұрын

    Mike it is still the same size just a newer unit with the bolt on blade. Good Luck!

  • @ampedgear1721
    @ampedgear17214 жыл бұрын

    Thanks man! Replaced my blower fan today with this.

  • @JasonJonieBuilds

    @JasonJonieBuilds

    4 жыл бұрын

    Glad to help. In the sandy south the blowers don't last too long.

  • @rodmckim5991
    @rodmckim5991 Жыл бұрын

    Awesome content.....getting ready to tear down mine..... Thanks again Jason!

  • @JasonJonieBuilds

    @JasonJonieBuilds

    Жыл бұрын

    Thanks Rod. Good luck

  • @dannyeugenewaits9486
    @dannyeugenewaits9486 Жыл бұрын

    I'm getting ready to do mine tomorrow...wish me some luck!

  • @JasonJonieBuilds

    @JasonJonieBuilds

    Жыл бұрын

    It is not too bad. Good luck.

  • @Sandman56
    @Sandman563 жыл бұрын

    Thank you for taking the time to make this video. It is very detailed and easy to follow. I k ow it helped me and I am sure it will help others also. Nice job!!!!

  • @JasonJonieBuilds

    @JasonJonieBuilds

    3 жыл бұрын

    Thank you Joe! I figured I was not the only one who had to replace these things often. Thanks for watching.

  • @isaacchavezjr5556
    @isaacchavezjr55563 жыл бұрын

    I wish you were around when I first took my blower housing out. I did take some good ideas on how to do it in the future. Like tipping over the walker instead of lifting the whole thing up. But I have one idea for you that I didn’t know Was possible . Instead of stabbing The deck into the female shaft. You can actually take the female shaft off and mounted on the Mail shaft and put it all back on to together. There is a quick release that mounts it up the directional driveshaft under the mower.

  • @JasonJonieBuilds

    @JasonJonieBuilds

    3 жыл бұрын

    Thanks Isaac! I hope it helps. Thanks for watching.

  • @mgyer2218
    @mgyer22182 жыл бұрын

    Nice camera work very clear video

  • @JasonJonieBuilds

    @JasonJonieBuilds

    2 жыл бұрын

    Thank you!

  • @alittlebitofeverything5090
    @alittlebitofeverything5090 Жыл бұрын

    Very informative thank you! I'm in the process of replacing the stator on mine. It is time consuming pulling the motor. Wish it was a vertical crankshaft lol! I haven't replaced a blower assembly yet, but your video is very helpful for when the time comes.

  • @JasonJonieBuilds

    @JasonJonieBuilds

    Жыл бұрын

    Thanks! Good luck on the stator. Nothing is easy on a Walker. It is all so tight.

  • @alittlebitofeverything5090

    @alittlebitofeverything5090

    Жыл бұрын

    Thanks. Yes tuff to do anything on them without getting banged up a little!

  • @Jflowboston1
    @Jflowboston12 жыл бұрын

    I did it today, thanks for video, but if some one need to replace just the propeller get ready both bearing and shaft and be careful removing the pulley I broke mine with a small puller, so I had to buy a new one

  • @JasonJonieBuilds

    @JasonJonieBuilds

    2 жыл бұрын

    Yes sir. That pulley is cast and will break pretty easy. Glad it helped.

  • @louiskittel8459
    @louiskittel8459 Жыл бұрын

    THANKS for the Great Info!!! VERY Helpful 👍

  • @JasonJonieBuilds

    @JasonJonieBuilds

    Жыл бұрын

    Thanks for watching!

  • @michaelodonnell5536
    @michaelodonnell55363 жыл бұрын

    Great video...have done a few..that tip on the splined shaft was helpful

  • @JasonJonieBuilds

    @JasonJonieBuilds

    3 жыл бұрын

    Thanks for watching Michael.

  • @babyoda1973
    @babyoda19732 жыл бұрын

    Quick tip pull the red side handles before the spring

  • @JasonJonieBuilds

    @JasonJonieBuilds

    2 жыл бұрын

    Thanks,

  • @Matt-lt8xg
    @Matt-lt8xg Жыл бұрын

    Your video is awesome! I’m thinking about doing this to mine! I have to try to find a good place to buy parts online.

  • @JasonJonieBuilds

    @JasonJonieBuilds

    Жыл бұрын

    Thank you! They are available for sure. You just have to look around.

  • @amirmoshfeghi122
    @amirmoshfeghi1224 жыл бұрын

    Very informative and detailed video. I will check my mower for this issue.

  • @JasonJonieBuilds

    @JasonJonieBuilds

    4 жыл бұрын

    Thank you sir! I appreciate you watching.

  • @kc8ncr
    @kc8ncr2 жыл бұрын

    I wonder if that belt tensioner had ever been greased. Its not easy to get to. Nice video.

  • @JasonJonieBuilds

    @JasonJonieBuilds

    2 жыл бұрын

    Thanks

  • @jimmydickson8854
    @jimmydickson88542 жыл бұрын

    Thanks for the tutorial very helpfull mate jimmy D Aust

  • @JasonJonieBuilds

    @JasonJonieBuilds

    2 жыл бұрын

    Thanks for watching!

  • @tjoe1980
    @tjoe19803 жыл бұрын

    Thanks for the video, very informative thank you brother!

  • @JasonJonieBuilds

    @JasonJonieBuilds

    3 жыл бұрын

    Thanks for watching! Please subscribe we have more small engine content coming.

  • @tjoe1980

    @tjoe1980

    3 жыл бұрын

    @@JasonJonieBuilds I'm looking forward to it!👍

  • @raymccue4311
    @raymccue43113 жыл бұрын

    Thanks great job

  • @JasonJonieBuilds

    @JasonJonieBuilds

    3 жыл бұрын

    Thanks for watching!

  • @carlbeatty9638
    @carlbeatty96383 жыл бұрын

    great helpful video. Thank you for posting

  • @JasonJonieBuilds

    @JasonJonieBuilds

    3 жыл бұрын

    I am glad it was helpful. Thanks for watching!

  • @mgyer2218
    @mgyer22182 жыл бұрын

    Do you know why the drive shaft will only go together one way because the knuckles have to be timed otherwise the will fight against each other and wear out very quickly. FYI

  • @JasonJonieBuilds

    @JasonJonieBuilds

    2 жыл бұрын

    I understand that completely. I just wanted the viewers to understand the shaft will only slide together one way. Thanks

  • @kirilvlastanov444
    @kirilvlastanov4443 жыл бұрын

    can't thank you enough

  • @JasonJonieBuilds

    @JasonJonieBuilds

    3 жыл бұрын

    Thank you! I hope it helped.

  • @tgabe6163
    @tgabe61633 жыл бұрын

    Thank you so much!!!!!

  • @JasonJonieBuilds

    @JasonJonieBuilds

    3 жыл бұрын

    Glad to help. Thanks for watching!

  • @pmurp9x
    @pmurp9x2 жыл бұрын

    Thanks great video, going to look at one this week, the blower is supposedly seized and thus can't engage the blades. Is there any electrical lockout to stop the blades engaging or would it be because the belt can't rotate the fan. Thanks in advance

  • @JasonJonieBuilds

    @JasonJonieBuilds

    2 жыл бұрын

    Paul I have seen it both ways. Seized bearings and sticks debris locking up the fan. Also, the gearbox has given issues in the past making one think the fan bearings were bad. Good luck!

  • @pmurp9x

    @pmurp9x

    2 жыл бұрын

    @@JasonJonieBuilds cheers, all the best from Ireland

  • @jimmydickson8854
    @jimmydickson88542 жыл бұрын

    Are these walkers high maintenance mowers in general , how long will that new blower last give us a reply please thank you

  • @JasonJonieBuilds

    @JasonJonieBuilds

    2 жыл бұрын

    The Walker is a good mower. They don't need any more maintenance than the rest. They are more tedious to work on though. The blower lifespan is up to the soil/grass you have in your area. We are very sandy down here. I have seen a blower get used up in a year. Thanks for watching.

  • @babyoda1973
    @babyoda19732 жыл бұрын

    Way easier if you take off the tensioner pully

  • @Wishbone799
    @Wishbone7994 жыл бұрын

    Thanks, good detail will give it a go.

  • @JasonJonieBuilds

    @JasonJonieBuilds

    4 жыл бұрын

    Good Luck. It is not that bad just a little time consuming.

  • @uluaiono528
    @uluaiono5283 жыл бұрын

    2Mar21 1330 Thank you from me in Aotearoa New Zealand. Your video has saved me a huge amount of time and anxiety. You're a life saver. God bless you and bless you. Ulu

  • @JasonJonieBuilds

    @JasonJonieBuilds

    3 жыл бұрын

    Thanks Ulu! I am glad that it helped you. That video did much better than we ever expected. It was a job I have done many times. Take care.

  • @rajunbrain
    @rajunbrain3 жыл бұрын

    Great video how long did this job take you?

  • @JasonJonieBuilds

    @JasonJonieBuilds

    3 жыл бұрын

    If you have never done it I would say it will take you a couple hours. Thanks for watching!

  • @Adam_Newman
    @Adam_Newman3 жыл бұрын

    How much is a new blower ? I’ve gotten 8 years outta mine fixing to replace it, thanks

  • @JasonJonieBuilds

    @JasonJonieBuilds

    3 жыл бұрын

    Adam I will check with my buddy who owns the mower. He bought the replacement blower housing this last time. I will get back to ya. Thanks for watching.

  • @JasonJonieBuilds

    @JasonJonieBuilds

    3 жыл бұрын

    Adam, My buddy said it was around $250. for the assembly. Thanks

  • @Adam_Newman

    @Adam_Newman

    3 жыл бұрын

    Jason & Jonie Builds thanks man

  • @mikecooley3361

    @mikecooley3361

    3 жыл бұрын

    @@JasonJonieBuilds where’s he getting his? All the places I see are 360-390

  • @JasonJonieBuilds

    @JasonJonieBuilds

    3 жыл бұрын

    Mike, I will ask him. It is at a shop in either Troy or Montgomery Alabama. He has to drive an way to see them but they give him good deals.

  • @jimmydickson8854
    @jimmydickson88542 жыл бұрын

    He didn’t do his greasing ceased bearing bad boy

  • @JasonJonieBuilds

    @JasonJonieBuilds

    2 жыл бұрын

    Yep! It will show up if it is neglected.

  • @isaacchavezjr5556
    @isaacchavezjr55563 жыл бұрын

    I wish you were around when I first took my blower housing out. I did take some good ideas on how to do it in the future. Like tipping over the walker instead of lifting the whole thing up. But I have one idea for you that I didn’t know Was possible . Instead of stabbing The deck into the female shaft. You can actually take the female shaft off and mounted on the Mail shaft and put it all back on to together. There is a quick release that mounts it up the directional driveshaft under the mower.

  • @JasonJonieBuilds

    @JasonJonieBuilds

    3 жыл бұрын

    I will definitely check that out next time. Thanks for watching!