2009 VW Golf MK6 Rear Wheel Bearing How To Find the items that are used on the Dave Sterl channel in the Amazon shop. www.amazon.co.uk/shop/davesterl
Жүктеу.....
Пікірлер: 95
@davesterl2 жыл бұрын
Find the items that are used on the Dave Sterl channel in the Amazon shop. www.amazon.co.uk/shop/davesterl
@rimmersbryggeri17 сағат бұрын
COngratulations on using the MAnual impact driver. One of the best tools in the box!
@mechanicmatt8712 жыл бұрын
Hi Dave, I haven't ever managed to get the bolts tightened all the way, and neither has anyone in any workshops that I have worked with. Glad you liked the parcel. Cheers Matt
@squadmeta Жыл бұрын
Did this job today, was thankful I'd watched this and bought a heavy duty bar, I tried my standard one to compare and it was all flex. After the initial torque I managed to nudge the bolt round to 2pm then dropped it on the deck and got to 4pm, that was enough for me! The cap had sealer on unlike the one you had, was a nightmare, tapped it on square then got a flat piece of steel and gave it a fair few central whacks, worked well.
@JLsAutoSolution2 жыл бұрын
That is insane Dave.. I could just imagine my 5'5" 160lbs body trying to move that lol. Thanjs for sharing
@Simon67316 Жыл бұрын
I did the job today and got the hub nut 180 degrees using a torque multiplier. Bloody satisfying to see it rotating at such high torque with relatively little effort. Best thing I’ve bought recently and it was only £50.
@seanharris559910 ай бұрын
Great video! I got mine to 90 fairly easily and then on to pretty much 180 but broke the head on the US Pro 1572 breaker bar and broke the tip on a Laser 4025 on a 40” 3/4 bar doing it. Tool damage cost more than the bearing so stopping at 90 could be a good call!
@bogdanedu1557
2 ай бұрын
180nm
@jcon4162 жыл бұрын
Another great video dave. Always picking up valuable info especially after seeing that proper breaker bar in action .
@davesterl
2 жыл бұрын
Thanks 👍
@ElCid_862 жыл бұрын
I’m 188 lbs and had to stand on the breaker bar and voice up and down. Finally got it to 180*. Thanks for the video!
@danieldurnin9592 жыл бұрын
Great video as usual Dave. Similar brakes on My Skoda, mine where in similar condition too. Inside pads worn down to metal, one calliper stuck but managed to to move in eventually. I’m not mad about the design of the brakes on these. I think I’ll be keeping a closer eye on them than previous owner though.
@Subzero26982 жыл бұрын
Good video thanks. Just did this job myself on an Audi A3 and it was pretty easy. On the Audi A3 8P you don't even need to remove the caliper carrier as you can get the disc off without removing it, which makes the whole job nice and easy. The tightening of the axle bolt was difficult - I got to 90 degrees and couldn't do anymore. My 1/2 breaker bar with an added cheater bar was bending and i was worried something was going to break so left it there. It's still on crazy tight though so hopefully it isn't going anywhere! What make/model breaker bar do you use? It looks heavy duty!
@mollywebster24472 жыл бұрын
Hi Dave another brilliant video What’s the brand of breaker bar you used can’t seem to find it anywhere
@Simon67316 Жыл бұрын
Really useful video Dave, thanks!
@freedomindarkness2352 жыл бұрын
Hello Dave have you had any experience with the front wheel bearing/hub assembly? I have front ones to do on my seat Ibiza 6j 2010 2.0tdi, I’m game for getting it done myself on the drive just worried about if the bearing/hub needs pressed in/out or can you buy the special tool to separate it from the knuckle? Thanks from a fellow norn iron guy 😂
@glennlozuke2688 ай бұрын
Solid video. Thanks Dave
@colinreid73052 жыл бұрын
In the past I have had issues with some aftermarket parts supplied by the costumer. The worst issue was suspension ball joints separating causing the driver to lose control. Today one needs to be mindful of many sub standard parts on the market both in terms of safety and longevity. As always an informative and professional video and excellent use of breaker bar. Your accent makes me homesick even after 40 odd years in Australia.
@davesterl
2 жыл бұрын
Yes mate, home is where the heart is. You will always be where you are from imo. Yes there are ball joint suppliers that i do not use as i know they will not last. Jury is out atm on these NAPA parts. Where are you from originally?
@colinreid7305
2 жыл бұрын
@@davesterl Born in Portadown Co Armagh. Served dual apprenticeship in Irish Road Motors in 1970.
@ssss-df5qz
2 жыл бұрын
Tell customers to accept the terms that if the parts they supply are incorrect, there is a surcharge for then going to get the correct ones. The simplest thing to do is say "no customer supplied parts fitted" - it simply isn't worth the hassle when in the half hour you're off correcting parts, you've lost an hour's work elsewhere.
@captaincookie88111 ай бұрын
Hi Dave, just want to ask about your review on the quality of the wheel bearing from NAPA. How is it holding up until now?
@virtisconsole12 Жыл бұрын
great video with good views and commentary all the way through, agree the 180NM + 180 deg is basically unachievable, because like you mentioned all the torque is being absorbed by the suspension and not getting delivered to the wheel bolt, but that is where I got on my A4 B8 RR bearing I just installed - different car because a different knuckle and axle shaft with it being Quattro but same story on the wheel bolt, I only could get a 90deg final torque which is plenty. I have a TDI jetta as well, with the LR cable sticking like you mentioned any thoughts on how to free that up short of having to replace it, I really would rather not have to open up the console that is a pain - thanks for your video here, very good content
@FailedEmmisions Жыл бұрын
Getting the 180° is pretty easy. I use the first breaker bar you showed off (which does have a slight bend in it) with my jack handle as a cheater and put all my weight on it with constant pressure. I'm also 6'4" and 230lbs so the weight probably helps 😅 (193cm and 16.5st/104kg)
@jackc70842 жыл бұрын
Love the SMA reference!
@user-by4oq2zw3z6 ай бұрын
Very good…warnings and all !!
@dbautowerkz67172 жыл бұрын
Hi Dave I work with the vag stuff day in day out, I usually do exactly what you do as a rule of thumb I say 180nm and 90 degrees as the 180 is not achievable. Thanks Derek
@davesterl
2 жыл бұрын
Cheers Derek
@user-rz6tq4ok8d2 ай бұрын
Clear valuable heads up thanks
@Markb86082 жыл бұрын
Enjoy from USA. As you said, they are mad with that kind of torgue. I ended bending a 1/2 breaker bar. I have 385miles on Jetta. They seem to go every 50-75k miles.
@petecurran39955 ай бұрын
Nice one, Dave! I suspect I've this job to do on mine - alerted by strange mucky orange deposit on disc edge and on pads, slight noise rotating and slight whiff of burned (polymer), so thinking seal in that bearing assembly.
@codymullen48753 ай бұрын
What would the torque specs be for the front bearing hub and axle bolt? I can't seem to find it anywhere
@86andyw2 жыл бұрын
Dave I never understand why manufacturers pre assemble bolts with thread locker already on them. Surely you’ll be fighting it when tightening the bolt and most of it will come off before the bolt is torqued correctly. Am I missing something? Cheers
@Mubmoh10 ай бұрын
For VW Polo mk5 techical manual suggests you do 70nm + 30 degrees.
@kevinpalmer74522 жыл бұрын
Always a bonus if the brake discs can be removed without disturbing those carriers those spline bolts can be Soooo tight. I’m with you on the extra thick beaker bar have one myself and does it make a difference.
@davesterl
2 жыл бұрын
aye, those common type breaker bars are actually rubbish
@jgrant11622 жыл бұрын
Hi Dave, another excellent video. I was impressed by your heavy duty breaker bar. I looked on your Amazon tools web page, but couldn't see it there. Could you tell me what brand and model bar you used in this video? Also I was thinking how much time, grief and effort you have saved viewers who naturally think you had to remove the caliper retainer, to access the disc for removal. It's a pity all manufacturers haven't adopted this system. Keep the videos coming, I always look forward to a new video from you.
@davesterl
2 жыл бұрын
seems the breaker bar is out of stock on Amazon. I'll put it up when it's available
@md5602 жыл бұрын
Great job Dave, the colour of outside edge of disc that red/orange is always telltale sign brake has been sticking, as regards the torque for the centre bolt I don’t think that is needed at all there is little force on that bolt the axle is the load bearing part here the bolt is just keeping it in place.
@davesterl
2 жыл бұрын
The high torque is there as this is what is keeping the two parts of the bearing together. I have mentioned this in other videos
@boxingmma645810 ай бұрын
What mm inner bore is this bearing
@kennedysgarage32812 жыл бұрын
You'll have to put on a bit more weight on Dave in order to get to the 180', I don't be able to achieve it either & I think it ain't coming out at that 90'. Nice walk through
@gmans78592 жыл бұрын
The little one paying for another job Well Done ! ...
@simonrawle78852 жыл бұрын
have you got a link for that bar . i need one for my locking wheel nut removal . keep braking the normal ones
@davesterl
2 жыл бұрын
i tried to add it to the amazon store but it's currently unavailable. Google US PRO 1572
@williamwicklow51922 жыл бұрын
Well done Dave i really enjoyed that video once again very educational 👍👏
@davesterl
2 жыл бұрын
Glad you enjoyed it
@the_retired_mechanic2 жыл бұрын
Straight forward enough hey Dave!!! They have simular silly torque spec on the front hub bearing on some audi cars. Always fear they will shear off when tightening them.
@davesterl
2 жыл бұрын
aye same deal on the fronts to hold the bearing together
@trevormansfield67402 жыл бұрын
I just do them up tight…!!!!!!. I haven’t used any Napa bearings yet. Let us know if it lasts. What’s your motor trade background Dave. If you don’t mind me asking?..
@davesterl
2 жыл бұрын
i've been working on cars since i was a kid
@drivewasher2 жыл бұрын
Hi, Dave, The only criticism I have it's VERY serious! Who makes that tea? It's like dishwater. I have the spoon stand up in it with a spot of milk. Yours looks like horlicks lol
@davesterl
2 жыл бұрын
Guilty! I've been slated before for my tea
@ilikebiscuits5672
2 жыл бұрын
Agreed, sort your life out
@Russell_Duncan2 жыл бұрын
Scaffold pipe on a 3/4” breaker bar for the bolt. Never broken one yet. Totally agree though; mental tight. Maybe a few more Ulster frys Dave, get some more weight swinging on it. Or at the very least, stick your wallet in you back pocket first 😜 Seriously though mate, another top job. 100% with the wee bit grease on the stub axle. If you ever have to pull that bearing again to maybe punch out an ABS sensor or something, you’ll be glad you greased it. I like to give the stub a wee clean with scotch-Britt too; can only help. 👍
@davesterl
2 жыл бұрын
your're a funny guy Russell lol
@cumbrianrider89032 жыл бұрын
you know its tight enough when its tight! never got more than 120 degrees on one myself.
@davesterl
2 жыл бұрын
aye, as tight as you can get it
@benmayne79102 жыл бұрын
Never heard of the napa brand outside of south main auto . We have been slowly getting more and more napa parts Coil springs seem really competitive on price. Vs regular suppliers
4 ай бұрын
That axle bolt. it's tight enough around there.
@hugogomes21432 жыл бұрын
Hi Dave! What's the tool you use to get the rear disc out of the bearing? It seems to be a kind of impact tool.....i use to hit it with a hammer....your way seems more professional and safer. Thanks 😉
@charlesdale1462
2 жыл бұрын
Impact driver. About a tenner
@TheGibby33402 жыл бұрын
Nice work Dave...Do you own a torque multiplier? I don't, but wish I did on occasion. And no...I don't mean a longer cheater pipe 🤣
@davesterl
2 жыл бұрын
Naw i don't, the HGV guys use those
@graaff914 ай бұрын
118 nm plus 180°degree turn colockwise. you say at the start of this clip. you end up doing only 118 nm and a quarter turn(90 clockwise 90°... why
@davesterl
4 ай бұрын
Do you not listen
@125sm32 жыл бұрын
The specs on that bearing bolt are ridiculous lol. Great call on the disc and pads.
@davesterl
2 жыл бұрын
Cheers
@epad19902 жыл бұрын
Great Video Dave but jesus do you want some tea with that milk?
@davesterl
2 жыл бұрын
Yes please!
@thecapedcrusader3262 жыл бұрын
Is that Poppy giving you some money to go and get her some ice cream? 😀🍦
@davesterl
2 жыл бұрын
Haha, she'll get a lot of ice cream with that wad
@rimmersbryggeri17 сағат бұрын
The autodoc tutorial says 75 newton meters for the stub axle bolt. 180+180 deg seems wildly excessive.
@davesterl
17 сағат бұрын
@@rimmersbryggeri that spec would be typical for 4wd variants
@rimmersbryggeri
17 сағат бұрын
@@davesterl Ok. But 180 + 180 is nuts. even 90+90 can be difficult to achieve in my expernce.
@davesterl
17 сағат бұрын
@@rimmersbryggeri I do say this in the video
@rimmersbryggeri
16 сағат бұрын
@@davesterl Yeah you do. :) And I support that opinion. Aparently the torque of that bolt is nominally 315 NM if you want to go NM all the way. I googled 315nm torque wrench and it returned 3-15nm as the result. Same for torque stick. Also you are aparently liable to cause damage to the bearing if you torque it on the ground. Dont mistake though I liked your video. And I got the answer to the question wether it's possible to remove the brake disc without removing the caliper bracket. Thanks! I hopefully won't need to remove the bolt after all since I only need access to get the broken abs sensor out.
@davesterl
16 сағат бұрын
@@rimmersbryggeri if you put weight on the bearing with the bolt loose then then bearing could be damaged. If it's tightened to the 180NM, a lot of guys would lower the car for final tightening. I don't see a problem with that provided the bolt has had it's initial tightening.
@ShadowIYI4 ай бұрын
Forget the wheel bearing, what on earth is that cuppa???😮😂
@mikeberry3042 жыл бұрын
Another top job Dave ,I am sat on me bum at home , we've all caught the nasty one , hopefully can go back out next weds , still no taste or smell , but the kids (teenagers can smell and taste ) , never watched as many utube videos , liked the Napa ref 😂😂, have done a few of these before , even cheated before undoing the when bearing to get the disc off when the carrier bolts look scarey , take care 💉💉, looking forward to being able to taste a chip butty soon 😂😂👍👍
@davesterl
2 жыл бұрын
Good man Mike, Keep the chin up. Take care
@chrisnicholais55872 жыл бұрын
No impact gun on that axle bolt says the Bentley
@davesterl
2 жыл бұрын
That's correct. Did you see me lossening or tightening the bolt with an impact?
@chrisnicholais5587
2 жыл бұрын
@@davesterl Maybe I'm hallucinating but the big green ugga dugga thing that runs on air sure seems like an impact. I watch you loosen and tighten it for 2 solid minutes of your video LOL
@davesterl
2 жыл бұрын
@@chrisnicholais5587 i ran the bolt in and out with the impact. Not loosened or tightened.
@maximus-6788
Жыл бұрын
vw also but not using it to tighten the bolt or loosening it. It will break.
@ssss-df5qz2 жыл бұрын
Ridiculous torque specs. I'm going to go 180nm then 90 personally.
@johnovegas Жыл бұрын
is this english?
@davesterl
Жыл бұрын
No
@pieciapiecia19
Жыл бұрын
No silly, its Chinese - same language, as you asked your question in...
Пікірлер: 95
Find the items that are used on the Dave Sterl channel in the Amazon shop. www.amazon.co.uk/shop/davesterl
COngratulations on using the MAnual impact driver. One of the best tools in the box!
Hi Dave, I haven't ever managed to get the bolts tightened all the way, and neither has anyone in any workshops that I have worked with. Glad you liked the parcel. Cheers Matt
Did this job today, was thankful I'd watched this and bought a heavy duty bar, I tried my standard one to compare and it was all flex. After the initial torque I managed to nudge the bolt round to 2pm then dropped it on the deck and got to 4pm, that was enough for me! The cap had sealer on unlike the one you had, was a nightmare, tapped it on square then got a flat piece of steel and gave it a fair few central whacks, worked well.
That is insane Dave.. I could just imagine my 5'5" 160lbs body trying to move that lol. Thanjs for sharing
I did the job today and got the hub nut 180 degrees using a torque multiplier. Bloody satisfying to see it rotating at such high torque with relatively little effort. Best thing I’ve bought recently and it was only £50.
Great video! I got mine to 90 fairly easily and then on to pretty much 180 but broke the head on the US Pro 1572 breaker bar and broke the tip on a Laser 4025 on a 40” 3/4 bar doing it. Tool damage cost more than the bearing so stopping at 90 could be a good call!
@bogdanedu1557
2 ай бұрын
180nm
Another great video dave. Always picking up valuable info especially after seeing that proper breaker bar in action .
@davesterl
2 жыл бұрын
Thanks 👍
I’m 188 lbs and had to stand on the breaker bar and voice up and down. Finally got it to 180*. Thanks for the video!
Great video as usual Dave. Similar brakes on My Skoda, mine where in similar condition too. Inside pads worn down to metal, one calliper stuck but managed to to move in eventually. I’m not mad about the design of the brakes on these. I think I’ll be keeping a closer eye on them than previous owner though.
Good video thanks. Just did this job myself on an Audi A3 and it was pretty easy. On the Audi A3 8P you don't even need to remove the caliper carrier as you can get the disc off without removing it, which makes the whole job nice and easy. The tightening of the axle bolt was difficult - I got to 90 degrees and couldn't do anymore. My 1/2 breaker bar with an added cheater bar was bending and i was worried something was going to break so left it there. It's still on crazy tight though so hopefully it isn't going anywhere! What make/model breaker bar do you use? It looks heavy duty!
Hi Dave another brilliant video What’s the brand of breaker bar you used can’t seem to find it anywhere
Really useful video Dave, thanks!
Hello Dave have you had any experience with the front wheel bearing/hub assembly? I have front ones to do on my seat Ibiza 6j 2010 2.0tdi, I’m game for getting it done myself on the drive just worried about if the bearing/hub needs pressed in/out or can you buy the special tool to separate it from the knuckle? Thanks from a fellow norn iron guy 😂
Solid video. Thanks Dave
In the past I have had issues with some aftermarket parts supplied by the costumer. The worst issue was suspension ball joints separating causing the driver to lose control. Today one needs to be mindful of many sub standard parts on the market both in terms of safety and longevity. As always an informative and professional video and excellent use of breaker bar. Your accent makes me homesick even after 40 odd years in Australia.
@davesterl
2 жыл бұрын
Yes mate, home is where the heart is. You will always be where you are from imo. Yes there are ball joint suppliers that i do not use as i know they will not last. Jury is out atm on these NAPA parts. Where are you from originally?
@colinreid7305
2 жыл бұрын
@@davesterl Born in Portadown Co Armagh. Served dual apprenticeship in Irish Road Motors in 1970.
@ssss-df5qz
2 жыл бұрын
Tell customers to accept the terms that if the parts they supply are incorrect, there is a surcharge for then going to get the correct ones. The simplest thing to do is say "no customer supplied parts fitted" - it simply isn't worth the hassle when in the half hour you're off correcting parts, you've lost an hour's work elsewhere.
Hi Dave, just want to ask about your review on the quality of the wheel bearing from NAPA. How is it holding up until now?
great video with good views and commentary all the way through, agree the 180NM + 180 deg is basically unachievable, because like you mentioned all the torque is being absorbed by the suspension and not getting delivered to the wheel bolt, but that is where I got on my A4 B8 RR bearing I just installed - different car because a different knuckle and axle shaft with it being Quattro but same story on the wheel bolt, I only could get a 90deg final torque which is plenty. I have a TDI jetta as well, with the LR cable sticking like you mentioned any thoughts on how to free that up short of having to replace it, I really would rather not have to open up the console that is a pain - thanks for your video here, very good content
Getting the 180° is pretty easy. I use the first breaker bar you showed off (which does have a slight bend in it) with my jack handle as a cheater and put all my weight on it with constant pressure. I'm also 6'4" and 230lbs so the weight probably helps 😅 (193cm and 16.5st/104kg)
Love the SMA reference!
Very good…warnings and all !!
Hi Dave I work with the vag stuff day in day out, I usually do exactly what you do as a rule of thumb I say 180nm and 90 degrees as the 180 is not achievable. Thanks Derek
@davesterl
2 жыл бұрын
Cheers Derek
Clear valuable heads up thanks
Enjoy from USA. As you said, they are mad with that kind of torgue. I ended bending a 1/2 breaker bar. I have 385miles on Jetta. They seem to go every 50-75k miles.
Nice one, Dave! I suspect I've this job to do on mine - alerted by strange mucky orange deposit on disc edge and on pads, slight noise rotating and slight whiff of burned (polymer), so thinking seal in that bearing assembly.
What would the torque specs be for the front bearing hub and axle bolt? I can't seem to find it anywhere
Dave I never understand why manufacturers pre assemble bolts with thread locker already on them. Surely you’ll be fighting it when tightening the bolt and most of it will come off before the bolt is torqued correctly. Am I missing something? Cheers
For VW Polo mk5 techical manual suggests you do 70nm + 30 degrees.
Always a bonus if the brake discs can be removed without disturbing those carriers those spline bolts can be Soooo tight. I’m with you on the extra thick beaker bar have one myself and does it make a difference.
@davesterl
2 жыл бұрын
aye, those common type breaker bars are actually rubbish
Hi Dave, another excellent video. I was impressed by your heavy duty breaker bar. I looked on your Amazon tools web page, but couldn't see it there. Could you tell me what brand and model bar you used in this video? Also I was thinking how much time, grief and effort you have saved viewers who naturally think you had to remove the caliper retainer, to access the disc for removal. It's a pity all manufacturers haven't adopted this system. Keep the videos coming, I always look forward to a new video from you.
@davesterl
2 жыл бұрын
seems the breaker bar is out of stock on Amazon. I'll put it up when it's available
Great job Dave, the colour of outside edge of disc that red/orange is always telltale sign brake has been sticking, as regards the torque for the centre bolt I don’t think that is needed at all there is little force on that bolt the axle is the load bearing part here the bolt is just keeping it in place.
@davesterl
2 жыл бұрын
The high torque is there as this is what is keeping the two parts of the bearing together. I have mentioned this in other videos
What mm inner bore is this bearing
You'll have to put on a bit more weight on Dave in order to get to the 180', I don't be able to achieve it either & I think it ain't coming out at that 90'. Nice walk through
The little one paying for another job Well Done ! ...
have you got a link for that bar . i need one for my locking wheel nut removal . keep braking the normal ones
@davesterl
2 жыл бұрын
i tried to add it to the amazon store but it's currently unavailable. Google US PRO 1572
Well done Dave i really enjoyed that video once again very educational 👍👏
@davesterl
2 жыл бұрын
Glad you enjoyed it
Straight forward enough hey Dave!!! They have simular silly torque spec on the front hub bearing on some audi cars. Always fear they will shear off when tightening them.
@davesterl
2 жыл бұрын
aye same deal on the fronts to hold the bearing together
I just do them up tight…!!!!!!. I haven’t used any Napa bearings yet. Let us know if it lasts. What’s your motor trade background Dave. If you don’t mind me asking?..
@davesterl
2 жыл бұрын
i've been working on cars since i was a kid
Hi, Dave, The only criticism I have it's VERY serious! Who makes that tea? It's like dishwater. I have the spoon stand up in it with a spot of milk. Yours looks like horlicks lol
@davesterl
2 жыл бұрын
Guilty! I've been slated before for my tea
@ilikebiscuits5672
2 жыл бұрын
Agreed, sort your life out
Scaffold pipe on a 3/4” breaker bar for the bolt. Never broken one yet. Totally agree though; mental tight. Maybe a few more Ulster frys Dave, get some more weight swinging on it. Or at the very least, stick your wallet in you back pocket first 😜 Seriously though mate, another top job. 100% with the wee bit grease on the stub axle. If you ever have to pull that bearing again to maybe punch out an ABS sensor or something, you’ll be glad you greased it. I like to give the stub a wee clean with scotch-Britt too; can only help. 👍
@davesterl
2 жыл бұрын
your're a funny guy Russell lol
you know its tight enough when its tight! never got more than 120 degrees on one myself.
@davesterl
2 жыл бұрын
aye, as tight as you can get it
Never heard of the napa brand outside of south main auto . We have been slowly getting more and more napa parts Coil springs seem really competitive on price. Vs regular suppliers
That axle bolt. it's tight enough around there.
Hi Dave! What's the tool you use to get the rear disc out of the bearing? It seems to be a kind of impact tool.....i use to hit it with a hammer....your way seems more professional and safer. Thanks 😉
@charlesdale1462
2 жыл бұрын
Impact driver. About a tenner
Nice work Dave...Do you own a torque multiplier? I don't, but wish I did on occasion. And no...I don't mean a longer cheater pipe 🤣
@davesterl
2 жыл бұрын
Naw i don't, the HGV guys use those
118 nm plus 180°degree turn colockwise. you say at the start of this clip. you end up doing only 118 nm and a quarter turn(90 clockwise 90°... why
@davesterl
4 ай бұрын
Do you not listen
The specs on that bearing bolt are ridiculous lol. Great call on the disc and pads.
@davesterl
2 жыл бұрын
Cheers
Great Video Dave but jesus do you want some tea with that milk?
@davesterl
2 жыл бұрын
Yes please!
Is that Poppy giving you some money to go and get her some ice cream? 😀🍦
@davesterl
2 жыл бұрын
Haha, she'll get a lot of ice cream with that wad
The autodoc tutorial says 75 newton meters for the stub axle bolt. 180+180 deg seems wildly excessive.
@davesterl
17 сағат бұрын
@@rimmersbryggeri that spec would be typical for 4wd variants
@rimmersbryggeri
17 сағат бұрын
@@davesterl Ok. But 180 + 180 is nuts. even 90+90 can be difficult to achieve in my expernce.
@davesterl
17 сағат бұрын
@@rimmersbryggeri I do say this in the video
@rimmersbryggeri
16 сағат бұрын
@@davesterl Yeah you do. :) And I support that opinion. Aparently the torque of that bolt is nominally 315 NM if you want to go NM all the way. I googled 315nm torque wrench and it returned 3-15nm as the result. Same for torque stick. Also you are aparently liable to cause damage to the bearing if you torque it on the ground. Dont mistake though I liked your video. And I got the answer to the question wether it's possible to remove the brake disc without removing the caliper bracket. Thanks! I hopefully won't need to remove the bolt after all since I only need access to get the broken abs sensor out.
@davesterl
16 сағат бұрын
@@rimmersbryggeri if you put weight on the bearing with the bolt loose then then bearing could be damaged. If it's tightened to the 180NM, a lot of guys would lower the car for final tightening. I don't see a problem with that provided the bolt has had it's initial tightening.
Forget the wheel bearing, what on earth is that cuppa???😮😂
Another top job Dave ,I am sat on me bum at home , we've all caught the nasty one , hopefully can go back out next weds , still no taste or smell , but the kids (teenagers can smell and taste ) , never watched as many utube videos , liked the Napa ref 😂😂, have done a few of these before , even cheated before undoing the when bearing to get the disc off when the carrier bolts look scarey , take care 💉💉, looking forward to being able to taste a chip butty soon 😂😂👍👍
@davesterl
2 жыл бұрын
Good man Mike, Keep the chin up. Take care
No impact gun on that axle bolt says the Bentley
@davesterl
2 жыл бұрын
That's correct. Did you see me lossening or tightening the bolt with an impact?
@chrisnicholais5587
2 жыл бұрын
@@davesterl Maybe I'm hallucinating but the big green ugga dugga thing that runs on air sure seems like an impact. I watch you loosen and tighten it for 2 solid minutes of your video LOL
@davesterl
2 жыл бұрын
@@chrisnicholais5587 i ran the bolt in and out with the impact. Not loosened or tightened.
@maximus-6788
Жыл бұрын
vw also but not using it to tighten the bolt or loosening it. It will break.
Ridiculous torque specs. I'm going to go 180nm then 90 personally.
is this english?
@davesterl
Жыл бұрын
No
@pieciapiecia19
Жыл бұрын
No silly, its Chinese - same language, as you asked your question in...