Thank you for showing us this! I hard getting this done even with the tools. Used a combo of the two to get her done!!! Glad I found your channel. Thanks for all your help!!!

Well done, Champ. Your videos and conversations are well-done and super helpful. You know those 3.6's like the back of your hand.

@OnlineMechanicTips

2 жыл бұрын

Thanks for watching Vince, appreciate that

You gave me the confidence to tackle this job! Thanks!

How to tell if your Cam Phaser Bad, How to tell if your lifters bad here: kzread.info/dash/bejne/ZGGNqsRvg5Xak9I.html How to replace Cam Phasers, rocker arms and lifters USING SPECIAL TOOLS here: kzread.info/dash/bejne/e42ImbeAg6-fY9Y.html

Saved me!!!!! after trying to do it by the book and broke the cheap "tool" working on the right side exhaust cam. The tool set seems to be more for DIY uncertainty. The main thing on doing this job is to MARK EVERYTHING even the things that don't seem to matter and probably usually don't. It will at least make you feel better. For mine there did seem to be a difference in the phaser bolts(I didn't mark them but did remember which one I put where). Had trouble getting one started and tried the other bolt, the one that came out of that side, and it almost threaded itself. For those saying the right bank is the hardest I would have to agree when it comes to my Grand Caravan simply because you(and especially "I") can't see and to do so requires at least 4 hands to hold the flashlight, mirror, tools, and the phaser. Even with my 60 year old arthritic hands I somehow managed. Using a short piece of 1/2" PVC pipe in the phaser hole made handling it and lining it up much easier. It would help having someone around holding the wrench on the cam while breaking loose and torquing the phaser bolts. I used a ratchet strap connect to an opposite side cam to hold the wrench while breaking loose and a short piece of 1x2 lumber under it while torquing. For those of you that haven't started on your FWD a 36mm combination wrench would come in handy for the phaser bolts after breaking them loose and before torquing as space, especially on the right bank, is limited. Go ahead and move the power steering reservoir out of the way too so you don't risk breaking it while torquing. Now if you could save me from having to buy a new left side exhaust cam! There wasn't a worrisome amount of noise and I didn't drive much after it started but 2 rollers were completely shot, no sign of needle bearings anywhere, and those two lobes were about 20% more narrow than they should be. One was no longer egg shaped unless you consider snapping turtle eggs. You should call this video Don't Panic If The Tools Don't Fit And/Or Break. Thanks for the great video and tips! KZread wasn't around when I had to deal with the same type locking tensioner on a 1977 Ford Courier with a 1.8 Mitsubishi overhead cam

I dunno who you are outside of these videos but I wish I did. I’d hire you in second if I could. As a technician turned team leader turned foreman who’s been doing this for over 20 years now, my rule has always been that flat rating a job is perfectly acceptable so long as it absolutely does NOT compromise the integrity or longevity of the repair or vehicle in any way. Also it absolutely CANNOT cost the customer more money then if the repair was done strictly by the book. If you take a shortcut and break something then that’s on you not the customer. Additionally all other consumables, seals, liquids, and fasteners that are required to be replaced and or torqued per the manufacturer must still be done. From many of your videos I’ve watched it sounds like you have a lot of the same beliefs in proper automotive repair. Much respect!

Thank you for giving me the courage to do this job i had to change out a intake cam and rockers on a 2015 journey bank 1 (right side) Thank you again and god bless i really enjoyed you videos!!!

@OnlineMechanicTips

2 жыл бұрын

Thats whats up and thanks for watching the vids bud.

Thank You!!! Now I can just apply this to the camshaft and rocker replacement since I don’t have the special tools at my shop🙏🏾🙏🏾

JT, you gave me the confidence to tackle this. Order four cams and 48 piece rocker and lifer set, intake and valvetrain cover gasket set, chain tool and paint pen all under $1,400 bucks ! All OEM. I drove 3 k miles with the bad tick and not willing to push my luck. Even dealer service guy pulled me aside when I had a headrest recall done. He said “off the record, that can cause catastrophic failure at any time”. Maybe I’ll get lucky and will find one or two serviceable cams and can return what I don’t open.

That was clean...great video👏👏

I love watching your videos. I am a pentastar mechanic myself. I build pentastar engines and have done so for the past 7 years. I worked on one for the first time under the hood and I must say it can be a beast at first but I prevailed. And even still I utilized your videos most of the time before tackling the job. Lucky for me it was a front facing chrysler 300 engine. Your are a trailblazing mopar man after my own heart. Keep up the awesome work sir.

@OnlineMechanicTips

3 ай бұрын

Thanks for tuning in Kevin. I appreciate that

@marqueezwright3408

3 ай бұрын

I need both of y’all help, I had a oil leak and day before oil cooling housing got delivered car gave out at the light got it towed changed the alternator AGAIN but now when starts the engine knocks. And idk if is the lifter or camshaft but someone also said timing chain but I have NOO idea (2012 Chrysler 200 3.6l)

You’re a Star JT! Thanks for video I’m doing rocker arms on bank 1 in my 3.6 2012 jeep wrangler soon. This helps big time. Thanks! I was a flat rate tech for years at GM dealer. Commission teaches you things!

Thanks to u I’ve removed my cams and heads using ur methods I didn’t have to remove the timing cover On my charger sxt 2014 Now I have no doubt I can put everything back together after watching this I’m gonna go send my heads out to get resurfaced and tested later on this weeks and then I’ll do my head gasket and start putting everything back together this is my first time removing head on a engine I’ve always just swapped them Im doing this because sxt was over heating due to running some test and coming back to head gasket

Hi JT: first of all. Great video. without the special tools, have to adjust the cam shaft to put the phasers on. Then have to use wrench to hold the camshaft while tight to torque specs. A very fast way to do it. It really requires a lot of practice ☺️

Nice job bud, busting open my front cover soon on my old pathfinder, trying to get to my hydraulic lifters under the cams... thanks for giving me some safe advice!

@OnlineMechanicTips

3 жыл бұрын

Thats whats up, thanks for watching.

Your the mannnn thanks for this very informative video!!!! I love what you do an thanks for sharing you got the swag an the skills. Straight up

@OnlineMechanicTips

3 жыл бұрын

Thanks for watching bud. Appreciate that.

Always great content thanks JT

@OnlineMechanicTips

2 жыл бұрын

Appreciate it!

Got bank 1 today. bit of a struggle getting the slack to put the intake phaser on after doing the exhaust camshaft but I kept jiggling the shafts and had to haul up on the phaser to get the oil control bolt all the way in! I used the special tool but it didn't give me all the slack I needed without shifting the cams back and forth I wouldn't have got it and did it the way you did it and it worked in your other video with the special tool! Second time I tried the right bank, last week I was afraid to take the chain off one of the phasers and let it lay. After this video I figure I should be able to get it with the special tool today cause last week I seen that by shifting the camshaft(intake) provided slack in the chain with the tool in place. I have a 2015 Dodge Grand Caravan. The actuators were in a tight spot along with the intake oil control bolt with the silver cylinder in the way of the wrench, I need a new breaker bar lol. Everything pretty tight in this vehicle, I'd image it's the same with the others. Bank 1 your doing some blind wrenching, feel for this and that 2015 dodge grand caravan. Have a good one. Cal

I did it this way when I changed my rockers and lifters, no issues whatsoever! Took my time removing the timing wheels when knocking them out with a wrench and had my hand on the other side to hold it in place. Had some fishing line to hold the timing chain in place that I ran to the hood latch.

Thanks again for another great video!!! You saved me when the plastic tool broke while trying to release tension in bank one/right side. Ended up watching this video and doing your procedure, the JT way :). Thanks!

@mattm2411

Жыл бұрын

my plastic tool broke just now. you left the plastic broken off piece inside the timing cover? or just did an oil change right after?

@jefffarschon4270

Жыл бұрын

@@mattm2411 - lol no I fished all the pieces out with a snake grabber. I was lucky they were all big and made a complete tool when out... took a longtime to do. If that did not work I would have had to pull the timing cover (not fun).

@mattm2411

Жыл бұрын

@@jefffarschon4270 my piece was so small o left it in there. ran fine. ill never use special tools again though

Thank you sir . I done my car . Because of your video

I had a cam phaser kicking my ass and you just saved me.. I love you man 👊🏼

@OnlineMechanicTips

2 жыл бұрын

lol, thats whats up. Please remember to thumbs up the video and subscribe to the channel, thanks.

@MichaelWilliams-nj6uk

2 жыл бұрын

@@OnlineMechanicTips done deal

Wow! now I see why you have so many subscribers; you are awesome!

@OnlineMechanicTips

7 ай бұрын

Thanks for tuning in my guy.

That was a very informative video JT, Looks like you’ve done a few of those lol

Smooth as butter.

Bro you Life saver 👍

This is like a cheat code. I guess if you mark everything and the chain is still connected on the other side it cant really get messed up. Thanks for the down and dirty

Thanks for the video

JT, have you done any videos on how to visually check the phasers while you have them off, for example when you replace a cam for a cam follower failure?

Thanks for your great videos. Definitely learning a lot. Im replacing the timing chain on a 3.6 engine in a 2014 Grand Cherokee. When I put cylinder 1 bank one/passenger side on TDC on the compression stroke all sprockets/phasers end up backwards and upside down. Is it possible it was put back together backwards by some else. It looks like someone had done work on it already. Any help will be greatly appreciated. Thank you.

So far, excellent videos! I want to check my vvt oil control solenoid on my 2015 Ram 1500 with the 3.6L engine. I haven’t been able to find the location of that part. Can you help me? Thanks in advance for answering.

Sir I’m subscribed to this channels I’m doing this job and things gone smooth on my 2014 sxt 3.6 penstar got I the cams of on my both heads I know u said the driver side head U can remove with the trick and tool to get k. The tight spot But is passanger bank able to be removed to without timing cover coming off ?like the driver side ?

I need help, man. I pulled and replaced all my rockers myself, no problem. Drives fine for a while, then rattles again. Then I pulled and replaced all my lifters. Drives fine. I finally found some camshafts to replace my nasty ones, so I pulled and replaced the right bank exhaust camshaft. Put it back together and it wouldn't start. I messed up the timing, so I opened it up and lined it back up. Great. Starts and drives fine. Time for the intake camshaft and here's my problem. I'm at the finish line. Got the intake camshaft in and I'm at top dead center with the crankshaft. My phasers are perfectly lined up with the dark timing chain links, exactly the same as the left bank. My cams are all at top center. I put it all back together and try to start it. Clunk clunk dead. Won't start. Any advice on what to check would be great. Appreciate it.

Hey men when does cam phasers go bad your check eng comes on? , or why you replace them ?

How do you know if your cam phaser is no good?? Appreciate the great info! Thanks

Thank you

Great video! Thank you! What are the torque specs for the phasers?

@OnlineMechanicTips

3 жыл бұрын

kzread.info/dash/bejne/qquIm9xvg6WfnJM.html

How did you get your valve cover off with the trans filler tube there!??

question, I changed all rollers and rockers some how my marks got off my mistake I'm sure my question is when comes to timing everything stats that the 3.6 times at TDC on the exhaust stroke this seems strange to me I always thought it would time TDC on compression stroke any help would B greatly appreciated. Thank U

I have seen other mechanics take the cam sensors off the valve covers before removing the valve cover. That may help with removing the valve cover. Make sure to replace cam sensors back to the same cam phaser. I haven't heard of cam phasers malfunctioning, but I do know that material can get stuck inside the cam phaser and that you could clean it out instead of replacing with new cam phasers. Also, I didn't see you use any tool to depress the tensioner, but I didn't understand how you still had all that slack. Must not matter so much, but correct me JT.

So I guess while I was working on a 15 ram tradesmen 3.6 driver side intake side the tool shot out and the tensioner extended out all the way and I can get JT to release and get my tool back in the right spot and to make things worse the cam jumped time and I can’t get anything to go back correctly what do I have to do to fix this problem I really need some help

J t nice teaching boss

YOU MUST BE SO FAMOUS NOW BC I CANT GET A REPLY LOL😂ANY WAY the motor i replaced rockers and lifters why when motor is cold it sounds beautiful but when it build a little heat it sounds like the chain is loose or something tia

Hey so I messaged you the other day on my husbands account. We had replaced rockers, lifters and a cam we thought we jumped time after we turned it over had someone come and look at it turns out we didn't jump time. when we started the vehicle the idle was rough so i shut it off and then tried starting it again but it wont start now it turns over just wont start any suggestions?

What socket are you using to loosen the cam

Great Vid....thanx.....i noticed that the phaser magnets on the rear of all 4 camshafts have some kind of grease on them' all the way around each one, kinda silvery looking. your vid shows that too. Should it be wiped off? A new cam does not have a special lube pack from rock auto. . Is it necessary or is that a metal build up?

@OnlineMechanicTips

2 жыл бұрын

Yea man thats like powdered shaving being atracted to the magnet. You should clean that off because the cam sensor needs to read that. Thanks for watching

JT, some guy changed bank 1 exh camshaft to try and clear a camshaft sensor code. Now car drives under powered, wont shift right and 0014/0017 are coding. The timing marks dont line up perfectly on bank 1 phasers. How can I tell if he re assembled in the wrong chain position or more likely a bad phaser? Please help...Im opened up and looking at it many hours...Alan In Boise ID

Less talkie talkie, more workie workie!

@OnlineMechanicTips

4 ай бұрын

Lmao

i've had that right bank (1) tensioner plunger pop all the way out on me and I had to remove the supercharger, intercooler and timing cover etc. major suck!

Bro you need to move to Austin Texas I’d go to you for all my work I may just drive up where you’re at to do some work on my 2014 Charger

Is there a torque spec for the vvt on the camshaft???

What size of wrench to hold the cam while unbolting it?

Buenas tardes entonces por el árbol de levas por donde la va la válvula pcv pasa aceite por ahí

Awesome video. Can you explain about how to time a 2010 Mazda CX-9 3.7 duratec engine. How would you verify the engine is in TDC on the compression stroke other than relying on the timing marks?

@garyr7027

Жыл бұрын

One simple way of verifying any engine TDC on number 1 cylinder. Remove all the plugs except for number 1 cylinder. Rotate the crank shaft by hand while looking at the timing marks. Once you feel the compression on that cylinder you know it's close to TDC, then simply line up the timing marks, as by then you're right there at TDC. It works every time, can't go wrong as long as the crank shaft timing marks are there.

@justincross7721

9 ай бұрын

Ford tech here. the dowel for the crank gear should be pointing at 12 oclock. that will be close enough and when you put the chain on just use the colored links to match up the dots on the cams and crank gear and you will be fine. cant mess it up that way. just make sure to crank the crank pulley down tight or you will have trouble later

I would like to sit and drink some beers with you and talk about mechanics

Hello,sir. When need change dodge engine 3.5 - 3.6 chains?? 200k miles ? 300kmiles? Or more? Thanks !!!!!!!

Nice. I do have a question for you. a shop told us that its either check Phaser or tone ring? Phaser I got but how can you test the tone ring? Its on the back of the cam right?

@OnlineMechanicTips

Жыл бұрын

Yes the tone wheel are pressed fit on the rear of the cam shaft. There is a tool for testing it. Also are you subscribed to the channel?

@OldGunner41

Жыл бұрын

I am. I’m in a whole new world now. So what would these tools look like to test it? Measurement, sound, X-ray? I can’t even fathom how to test it.

JT this is some witch craft!!! How is the tensionor on the other bank not extending out and stopping you from putting the phasers back on???

@OnlineMechanicTips

3 жыл бұрын

lol, no witch craft sir. Thats why i just let the camera roll and did not chop up any part of that clip. So you can see that it do not take a lot of slack at all to put them on. Its all in the positioning of that camshaft that you turning with the wrench an slightly lifting up on the chain/phaser to create even more slack.

have you noted how different torque specs for oil control valve on same engine but different makes and models?

@OnlineMechanicTips

3 жыл бұрын

No I havent. Thats interesting. I need to look into that, thanks

I just bought a 2015 caravan and both exhaust valve cam lobes are worn away on cyl 2! engine making almost a rod knock sound??? Is the sound from trapped combustion? All other cam lobes look fine on left head. Have not looked right head yet but engine ran like it had 1 cyl dropping out. Question is - why did both these only lobes wear away? Was there a blockage of oil supply or thats just the way they fail?? Also, how do you know that the phasers are bad on the engines you service?? Your advise on how to proceed with this repair and what to change? Just swap the cam and the two lifters and rockers for cyl 2?

@stephenlavine9346

3 жыл бұрын

Sounds like you have bad rocker arms. The bearing failed and wrecks camshaft.

s there a way to adjust the timing without marks? I took the chain out and my stupidity allowed me to turn the the sprocket s individually, which turned the cams. Now I have no idea where I am at. Call me an idiot because I am. 2015 Chev malibu 2.5

How did you back the VVT/phaser bolts out when your socket was going clockwise when you switched to the Fuel ratchet?

@OnlineMechanicTips

11 ай бұрын

I have no clue what you mean dude. What you talking about?

Question, this doesnt require to release tension from the timing chain tensioner right? Im only working on Bank 1 side and would love do exactly this method without messing with the tensioner

@OnlineMechanicTips

6 ай бұрын

Yes it requires that. I highly suggest you use the proper tools design for this job.

Ever run into chain jumping a tooth or two to the left after pulling out cam phaser on intake side there ? Meaning had all set to TDC made my marks on chain, phaser its all straight as it should but when I pulled oil control valve bolt/ then cam phaser off the chain some how went left a tooth but cam and phaser stayed straight at TDC...reaching out hopefully some knows what I'm saying and can steer me in right direction.. thank you

@OnlineMechanicTips

2 жыл бұрын

Hey bud, im curious if you are using the special tools? There are tools design to prevent this and keep chain guide in position while you dissasemble valve train. This video was done without the proper tools because somebody wanted to know how I do it. Also are you subscribed to the channel?

@AcousticDonkey

2 жыл бұрын

@@OnlineMechanicTips hey man thank you for getting back to me. yes id did subscribe! I'm trying to do this without the special tools at the moment.

OMT, is there a small amount of backlash between the camshaft and the phaser? if you put the wrench on the Cam, will it move a hair independent of the phaser?

@OnlineMechanicTips

Жыл бұрын

It depend. Are you on bank 1 or bank 2? Which head? Also are you subscribed to the channel?

@D4MI0N

Жыл бұрын

@@OnlineMechanicTips I'm subscribe now LOL! Right side head. 2015 Town and Country! Thanks!

@OnlineMechanicTips

Жыл бұрын

@@D4MI0N Vans are fwd vehicles so im assuming you me bank 1 which is the one not in front of the radiator,. Yes, it depend on houw much the tensioner extended. The video you on is for a RWD car but its bank 1. Watch this video and you may get a better understanding. kzread.info/dash/bejne/oYl8sJOAgrCpZ7A.html

If you're replacing the right bank 1 side valve train, is it necessary to remove the left bank 2 valve cover? I have heard to remove both side valve covers, even if working on only one side, but is it for ensuring that all four phasers/cams are aligned perfectly? Or can I just remove right valve cover? Thanks.

@OnlineMechanicTips

3 ай бұрын

Yea thats done for visual confidence. You don't have to. Just go by the marks on the phasers to assure timing will be on point.

@genep.6008

3 ай бұрын

@@OnlineMechanicTipsThanks for your response. It gives me more confidence in doing this job. Appreciate your informative, no-nonsense videos. Very educational, keep producing them!

I bet this is why I can't get rid of the P0024 code on my 09 Maxima.

Why is it so easy to put them right side phaser on when all i need is 1/16 inch more to install. I hope the timing chain hasn't come off at the bottom. I did this one time before ... the marks were off so I'm doing it again.

I can’t find ANYTHING on the 2014 impala. It has a tick that’s 99% coming from the valve train, but the bottom of the timing chain cover is over the bottom portion of the oil control valve. Can’t get the locking block in so I’m a little iffy. 🤦🏾‍♂️

Will a bad bank 1 cam phaser cause a bog down or lack of communication with the position sensor?

@OnlineMechanicTips

10 ай бұрын

What codes did you find guy? Also are you subscribed to the channel?

Question: How do you know if or when the Cam phasers are bad or when they need to be replaced?

@alexanderkasyanov4946

Жыл бұрын

I was wondering the same thing

@garyr7027

Жыл бұрын

They knock at start up and might even set a engine code.

6:32 Job start. Make it look so easy.

So it’s okay for the timing chain to be that lose when doing this job? I was afraid of it sipping a tooth or coming lose and having to take the timing cover off

@OnlineMechanicTips

2 жыл бұрын

Hey bud, for the record, this is a terrible video and could be mis leading..I do not recommend you do it this way.USE THE TOOLS. This the way I do it because I'm pressed for time and I have done a lot of them so the theory fairly simple to me

@nathanshelinbarger6306

2 жыл бұрын

So you can get by when doing the left side but can’t do the same on the right because the tensioner?

@OnlineMechanicTips

2 жыл бұрын

@@nathanshelinbarger6306 I dont use tools for either side. YOU NEED THE TOOLS TO DO IT RIGHT. Also are you subscribed to the channel?

Hello, my 2011 town and country has leaking valves. At 74k miles only on the front cylinders or bank 2 I believe. How much work is it to replace valve stem seals?

@OnlineMechanicTips

3 жыл бұрын

How are you so sure valve seals are your problems? Also are you subscribed to the channel?

@mon-ti6bx

3 жыл бұрын

@@OnlineMechanicTips Its clearly visible from the intake openings while replacing the oil cooler. Good amount of oil on one of the valves.

how does the timing chaim tensioner not get fully extended?

@OnlineMechanicTips

7 ай бұрын

It's a stradegy I use when I bring up TDC. I can't explain because it's a feel. But I highly recommend no one to do this. Not a good idea, please use the tools.

But what about the tensioners, aren't the timing chain teeth supposed to move if you don't use the proper tools?

@OnlineMechanicTips

2 жыл бұрын

Hey bud, I highly suggest you to use the proper tools to do this job. The only reason this video exist was because guys wanted to how I really do it..We work off time so after doing a number of these jobs you tend to understand and create shortcuts.

@garyr7027

Жыл бұрын

​@@OnlineMechanicTipslol... yeah good advice, use the right tools unless you know a short cut and how to utilize it.

hi JT, can you help me please, I have a 2012 jeep wrangler 3.6 pentastar, I'm trying to fix the ticking problem, I did your test 👍 and I rotate the engine from the harmonic balancer and I noticed that the chain skips , what can be the problem?? also the camshafts are not aline

@OnlineMechanicTips

3 жыл бұрын

O nooooo, the chain not suppose to skip a tooth. Curious, were you rotating counter clockwise? You may have to take the timing cover off now to get engine properly in time and replace that tensioner while you at it.

@orenkrief

3 жыл бұрын

@@OnlineMechanicTipsthank you JT for the quick response, I did rotate it clockwise , Is there a chance that the chain is not doing its job properly? or the tensioner? can it be done in a home garage?

@OnlineMechanicTips

3 жыл бұрын

@@orenkrief Yes, there is a chance that the tensioner not doing its job. On a Jeep Wrangler, this can be a little bit of a hassle not being on a lift.

@orenkrief

3 жыл бұрын

@@OnlineMechanicTips thank you I appreciate your answer I'll let you know in a few days what was wrong

@orenkrief

3 жыл бұрын

its was the timing chain tensioner it was broken

Looks easy when you do it. Is it me or the 3.6 seam to have alot of valve problems.

@OnlineMechanicTips

3 жыл бұрын

No valve problems. Valve train sys problems maybe. Mainly poorly built rocker arms that has been repaired nod.

Can the phasers be disassembled, cleaned and reused when sludged up?

@OnlineMechanicTips

Жыл бұрын

I have never made an attempt at such a repair. Im not sure buddy

@garyr7027

Жыл бұрын

I seen a guy take a phaser apart once in a video, he could not get it back together and ended up replacing it.

I did this and i think my shit messed up, when i start it it makes a screeching noise, throwing error code P0019 and P000C, does that mean my timing is off?

@OnlineMechanicTips

2 жыл бұрын

Likely, curious, did you mark it before taking it apart? Because at the point you simply put it bact together using the marks on the new phasers. Also are you subscribed to the channel?

Do you have to drain the oil before doing this

@OnlineMechanicTips

11 ай бұрын

No, but I do a oil and coolant service after this

Torque specs ?

اريدالممزيد

Bro we already know mechanics take major shortcuts to save time because most of them work by the job and the job has a set amount of hours that supposed to take so if you can get ahead of that you're good if you get behind that you're screwed so no worries just don't f*** it up and you're fine who cares how you get it done

Do the cam phaser bolts go bad?

@OnlineMechanicTips

3 ай бұрын

What do you mean go bad? It's an oil control valve. Also are you subscribed to the channel?

🎉🎉🎉🎉🎉

What size socket is the phaser?

@DonCatherman

Жыл бұрын

36 mm...

b ank 1 has been a huge pain in the ass to line up. Dodge cam and lifters and rockers. F'n damn things will not line up!!!!!!

What was wrong with the cam phases?

@OnlineMechanicTips

18 күн бұрын

Throws timing off

Why is one bank easier to do.. I heard u mention that but don't understand how.. tell me please

@OnlineMechanicTips

Жыл бұрын

Timing set up differently on both banks, tensioner in a different position on each bank

@jasonmassey7883

Жыл бұрын

@@OnlineMechanicTips can I change out one can phaser without the tools.. I figure if I line the teeth on the sprocket I can tap it on and off with a hammer

@OnlineMechanicTips

Жыл бұрын

@@jasonmassey7883 im against that. You should get the tools. This a terribly advised video. Curious, whats wrong with the phaser? Also are you subscribed to the channel?

Why would someone get new phasers if they aren't visibly damaged?

@OnlineMechanicTips

2 жыл бұрын

A good looking phaser can be internally coming apart..

Those actually go bad?

@OnlineMechanicTips

3 жыл бұрын

Yes, they will fail when you least expect them to. Thanks for watching, thumbs up the video and sub the channel for me, thanks

What’s are the torque specs ?

@OnlineMechanicTips

3 жыл бұрын

Hey bud, its all in the description. Remember to thumbs up the vid and sub the channel if you not already, thanks

@juansaldivar4171

3 жыл бұрын

@@OnlineMechanicTips thank you 👍

@juansaldivar4171

3 жыл бұрын

Can you get me the part # on the phaser of this video

Watch Motor city mechanic

@OnlineMechanicTips

Ай бұрын

David my guy. But why you suggest that?

Cams not locked down?

@OnlineMechanicTips

Жыл бұрын

This is a terrible video and I suggest you not follow it. I only uploaded it because somebody ask me how I do it. The thing with me is that I have done a lot of them so everthing simple to me. But no, the cams not locked down.

@garyr7027

Жыл бұрын

@@OnlineMechanicTips so long as you know a trick then go for it. I discovered a short cut to my 4.6 timing chain without locking the cams down by rotating the crank a few degrees off from TDC that lowers all the pistons down far enough so no valve will interfere. A little tougher to line marks up but still doable when double checked. Once timed up then it's good to rotate. In fact I got that method straight from a Ford repair manual timing section... trick to the trade.

Show Them how to put the engine at top dead center.

@OnlineMechanicTips

2 жыл бұрын

You should not even have the valve cover off if you dont understand the basics of TDC. Beside, this video not about that. When I do a video on that topic I will cover it in detail. Thanks bud

So the left side is the #1 bank

@OnlineMechanicTips

2 жыл бұрын

No, wait, what kind of car is this? Also are you subscribed to the channel?

An they alway's a couple curse word involved.

Thanks for videos. you talk too much! make your videos shorter! time if life!. why did you change the phazers?. also how with out pushing the camchain tentioner very easy you remove and install the phazers?! its not possible that easy.

@OnlineMechanicTips

2 жыл бұрын

I suggest you not do it like this so thats un-important. You should be using the special tools. I cant remember why these phasers was replaced. And for the record, content creators make videos the way they want to, when you watching something that irritates you, you suppose to simply click the stop button and move on. But your impatient ass chose to hang around and comment that somethings not possible that you clearly see happen.

Love it