Voron 0.1 3D Printer Full Build | LDO Motors Kit
Тәжірибелік нұсқаулар және стиль
This is a full build video of Voron 0.1 3d printer.
JLCPCB 3D printing from $1, Register to get $54 new user coupons: jlcpcb.com/3d-printing?from=3...
Official Voron site - vorondesign.com/voron0.1
PS : Yes I know it's very late as V0.2 has been already released.
Special thanks to @ldomotorsjason3488 for making this video possible.
-- Timestamps --
0:00 - Intro
0:23 - JLCPCB
1:16 - Inserting Brass Inserts
1:56 - Component Prep
2:17 - Rails Cleaning
2:47 - Rails Lubrication
3:09 - Y Rails
3:51 - Z Rails
4:26 - Bed Carrier
5:59 - Z Axis
11:34 - Frame
14:55 - A Drive
16:15 - B Drive
17:12 - A/B Drive
18:30 - A/B Idler
19:36 - Leadscrew Nut
21:06 - Feet and Leadscrew
22:29 - XY Joints
23:44 - X Axis
25:02 - X Axis endstop strike block
25:17 - Top Beams
25:56 - A Belt
27:09 - B Belt (Wrong screenshot in the video)
27:49 - X Carriage
28:14 - Belt Tensioning
28:27 - Print Bed
30:39 - X/Y End Stop
30:54 - Z End Stop
31:15 - Z End stop & Rear Panel
31:45 - Print Head (Component Prep)
32:59 - Fans
33:20 - Hotend
34:27 - Direct feed extruder
37:23 - Electronics and Wiring
42:47 - Skirts
----------------------------------------------------------------------------------------------------------------
Music provided by TheRelaxedMovement.
Check it out here: / therelaxedmovement
© Henry Keate t/a TheRelaxedMovement. All Rights Reserved
#voron #3dprinting #jlcpcb
Пікірлер: 14
good job and great tutorial , cant wait if you will make voron 2.4 RC2 tutorial same like this ❤
Are you going to share us the config process guide ?
@LoopLinks
17 күн бұрын
I haven't thought about it. For upcoming builds, I will try to share it.
where to get that GPIO PSU module for the Raspberry? thank you.
@LoopLinks
6 ай бұрын
It came with the kit. I don't see any third party selling it.
how much did you pay in total for the parts from jlcpcb? Their 3d printer service seems costly but for gantry parts it might not be a bad idea to get MJF printed parts.
@LoopLinks
Жыл бұрын
I did not order all the 3d printed parts from JLCPCB..Some parts I printed on my own 3d printer. Please go to their website and upload the STL files you will get the price.
@Unscientifically
Жыл бұрын
@@LoopLinks what parts did you buy from JLCPCB, and I did upload files on their site to see the price which is still alot
What filament is the silver colored prints made of, especially the tool head. Looks really good!
@LoopLinks
Жыл бұрын
It's not a filament. It's a PA12-HP Nylon - Natural Grey powder used in MJF 3d printer
What was the cost
@LoopLinks
6 ай бұрын
I paid $475 without raspberry pi and btt skr mini e3 v2.
Not using the Pico print board that was developed for this printer.
@LoopLinks
6 ай бұрын
I had btt skr mini e3 v2 lying around so I used that.