I'm also new to DLG and have a Spektrum DX6 transmitter, this video helped understand the modes and the various settings I need to consider for each mode. Thanks.

Thanks for the video it helps with the setup as I'm new to DLG THANKS again

Thank you for this. Gives great insight for a new comer to the DLG world.

@AndrewNewton

8 жыл бұрын

+PrettyFlowers Excellent, good to hear it.

@tripplorenzo8452

3 жыл бұрын

I guess Im kinda randomly asking but do anybody know of a good place to watch newly released series online?

@albertlevi2529

3 жыл бұрын

@Tripp Lorenzo Lately I have been using Flixzone. You can find it on google :)

@shilohchase658

3 жыл бұрын

@Albert Levi Yup, I have been watching on FlixZone for months myself :D

@tripplorenzo8452

3 жыл бұрын

@Albert Levi thanks, signed up and it seems to work :D Appreciate it!

Thanks, it’s these little things in life that add up🤠

Alex Paulsen, I'm using the Hobby King 6ch Rx with the case removed and replaced with heat shrink so it fits.

I've had a chance to try out the aileron and rudder mix combo. With both control surfaces moving the same way the plane turns sharper but the nose does tend to dip. You can compensate with up elevator. I'll try it the other way and post my thoughts. I did start using the rudder for turns in windy conditions and had a lot of luck making sharp, snappy flat turns (with oppose aileron to compensate). It proved an effective means of turning the plane in rough conditions.

Nice catch.

Love your channel keep it up

@AndrewNewton

5 жыл бұрын

Many thanks, I will

@factdesignbr

5 жыл бұрын

@@AndrewNewton thank you for the reply. After updating the firmware can you mix any switch to do whatever you want? How about a variometer with a frsky module on it? Can I also swap the two position switches to 3 positions? Thanks

@AndrewNewton

5 жыл бұрын

Better to buy a Taranis Q X7, but you can do any mixing and switch assigning you want with OpenTX. Dont know about vario telemetry with the FrSKY module, may be possible..

Are you using a stock Turnigy 8ch receiver?

just picked up a versus and read you need to cut down the boom , am asumming you would trim the part that fits in the fuse but by how much??? hope your getting this

@AndrewNewton

Жыл бұрын

50mm from the tail end. Here is the full build kzread.info/dash/bejne/lpd9psOBmpzTd7w.html

Thanks for the video. I set up my Polaris almost exactly the same. One thought, when you have rudder mixed with ailerons, shouldn't the rudder move in the opposite direction than the turning aileron? Opposite rudder in a turn helps keep the nose up in the turn and makes for a smoother, flatter turn. I think your set up will exacerbate the nose dipping in an aileron turn. Going to test my theory and report back. Thanks Again.

@AndrewNewton

10 жыл бұрын

Interesting, I have never thought of using opposite rudder. Wouldn't it add drag? Let us know how it goes.

@jstjern1

10 жыл бұрын

Traditionally, ailerons move an equal amount up and down. The up-aileron on the inside of the turn causes much less drag than the down-aileron on the outside. Then the nose does not move into the turn, but stays up, and the plane moves into what is called "side-slip". In side slip the fuselage moves somewhat sideways through the air, inducing additional drag. I use it for landings sometimes (i.e. aileron stick righ, rudder left, keeping wings level). Anyway, to compensate for this adverse-yaw, rudder is used to force the nose to lead the flight path, minimizing drag (but only as long as ailerons are deflected). Elevation/nose-up is done using the elevator, not the rudder (unless you do a knife-edge in 3D flight).

@jstjern1

10 жыл бұрын

Now, there's another way to avoid using much rudder, called aileron differential. Two paths: if you mount the aileron servos with the horns angled forward on both wings when the servo is centered, you create mechanical differential: the aileron moving up will move more up than the one moving down. How much differential you need is a trial-and-error thing, but assume about 50% (half down vs full up). This can be a problem on a DLG, where you want flaperons to deflect far down on landing, so most people install servos with the arms perpendicular to the wing, and dial in differential in the radio. The differential can then be suppressed as needed, i.e. when flaperons are deployed.

@jstjern1

10 жыл бұрын

I use TX programmed differential on my DLG, and cancel it on landing.

@ceradinimp

10 жыл бұрын

jstjern1 differentials is something I've meaning to get to. Thanks for the expantion, I will try the mix on my next trip out.

Dear Andrew Could u pls guide me . How I fix servo on receiver ?? Or any pictures of receiver can u share me ,? Which firm ware you are using with turnigy 9x ?

@AndrewNewton

2 жыл бұрын

Look for my RC Basics playlist, then you can ask more specific questions

Hay andrew, could you do a video of how to setup a dlg launch mode on a tx16s, i am still very new to opentx having come from spektrum, all im trying to achieve is the launch mode with 2-3mm up elevator and 3-5mm rudder as i only have a 2ch dlg. Cheers mate

@AndrewNewton

2 жыл бұрын

Yes, good subject for a video.

@skinnyguy3184

2 жыл бұрын

@@AndrewNewton wicked mate, looking forward to it 👍

Also pls guide what's smartie part board ? What's the use ?

@AndrewNewton

2 жыл бұрын

It allows firmware flashing. More information on the Smartieparts site.

Picture of OpenTX mix page with explanation added here - www.flickr.com/photos/pandasimages/15499945370/

Also guide model type GLIDER or normal fixing ?? To select

@AndrewNewton

2 жыл бұрын

I have lots of videos on glider steup

@tariqyounus3880

2 жыл бұрын

@@AndrewNewton thanks for your kind reply. Just pls guide I am using acro mode or glider mode for DLG?? I am new to this .hope u point out Thanks

hello and thank you for your great video. is it possible to share the eepe?

@AndrewNewton

6 жыл бұрын

eepe for the V2 DLG here newtonairlines.blogspot.com.au/search/label/eepe

@francois5623

6 жыл бұрын

thanks a lot andrew for you help

@goldenfish77

3 жыл бұрын

@@AndrewNewton Thank You for sharing link but Your video was that I could setup my DLG! Thank You for Your work and great videos!

Tanx alot, but if you have a photo of the mixing page on the seting it will be better for understand how you make this mixes. Tanx.

@AndrewNewton

9 жыл бұрын

דן סעדה Good idea, I'll put a picture up somewhere.

@dansaada

9 жыл бұрын

Iwill be very glad if you can take a picture and send me, im realy need help:) Dansaada00@gmail.com

Where did you get that DLG.

@AndrewNewton

7 жыл бұрын

Hobby King

@Helicopterpilot16

6 жыл бұрын

If only it was still available... But there's plenty of DLG manufactures around.

good video, i have a slightly different set up, i have put up a vid on my channel if you are interested, cheers,