Thx for that helpful Information. Especially on how much throws you have. Time to reprogram my TX and get out on the flying field. Cheers, Mike

@lotophagi711

5 жыл бұрын

Thanks. It's a great value DLG - I'm now on my second wing having broken the the first through stupidity.

Thank you, this was very helpful.

I'm just getting into DLG/setting up my glider and your video is fantastic sir! Great precise setup/work on your glider. Thank you for sharing Maat, really helps me to make things clear. Tally Ho! :) Regards Marc (Longshot1 + X9D Plus SE 2019)

@landendominick4906

3 жыл бұрын

dunno if anyone gives a damn but if you're stoned like me atm you can stream all the new series on instaflixxer. Been binge watching with my gf for the last days xD

@zachariahroberto6793

3 жыл бұрын

@Landen Dominick Yea, I have been watching on instaflixxer for since november myself :D

@terrellantonio5319

3 жыл бұрын

@Landen Dominick yea, been using InstaFlixxer for since november myself :)

@josephchristopher4347

3 жыл бұрын

@Landen Dominick definitely, have been using instaflixxer for years myself =)

Hi, Great video! Just getting into DLG with a Longshot 4 on my Taranis and have programmed other machines including F3F styly and Quads! I would be interested in viewing your files to understand what you have posted here!

looks nice, how capable do you think the maat is of some aerobatics on the way down? I've been looking to buy it!

@lotophagi711

8 жыл бұрын

Like most good DLGs the Maat can do areos (roll, spin, loop inverted). It's not designed to be aerobatic of course and being light does not carry its momentum well through loops - but they can be tight. It is very strong so you won't break it I think pulling tight maneuvers or going to fast.

what tx are you using?, I have a taranis qx7 and dont know if i trust it or not for the maat that I recently purchased from rcgliders.I also have frsky g-rx8 with vario built in.Do you think this rx will work?The tx you are using seems to be better than the qx7.thanks for any help you can give me,Im new to dlg and any help with this build would be appreciated.

@lotophagi711

4 жыл бұрын

Hi, I have an XD9 plus. I have had no problems with it in about 5 years. I use frsky d4r2 rx and their vario. I'm sorry I can't comment on the the qx7 or the rx8 as I have not used them. But as long as you can fit the rx in the very small fuselage it should be fine. Good luck

how important are rates do you think having a higher expo is better so you always have full deflection in trouble?

@lotophagi711

8 жыл бұрын

I tend to use high rates so I have a lot of throw but also have about 50% expo as well, so the controls are soft around neutral but can still get full throw if I need it. I think to fully exploit you need the best servos that that you can afford so that they have no slop and are really accurate - 1mm of play at the trailing edge of an aileron will ruin the the crisp feel of the plane. One of the best things I have with this plane is snap flap. I have not used it before but I think it makes tight thermal turns smoother, with less tendency to stall out. Definitely worth experimenting with.

Hi mate. Love your setup would there be any chance I could get your setup file for my L.D Stark? Pulling my hair out setting this thing up! Kinda miss how simple my Futaba was.

@lotophagi711

6 жыл бұрын

Hi John, let me have your email and I'll send it over with pleasure.

@johnbusuttil8958

6 жыл бұрын

Lotophagi jjb1108@gmail.com Thank you so much. Mine works kind of but I really like how your altimeter reads the alt after push over...would I need any specific help setting that up with my x4r and frsky variometer?

@lotophagi711

6 жыл бұрын

From memory I assign a switch to play the alt value when the elevator goes above neutral - as in moving the stick forward for the push over. Its been a long time since I looked at the code but I think L9 is assigned. In order to hook up the vario to the x4r you need to fiddle with wiring a bit but it's not too difficult. Have a look here at Scruffy's post www.rcgroups.com/forums/showthread.php?2177662-taranis-time-%21-getting-a-vario-and-monitoring-into-the-binary. He has the wiring diagram there. I built a power loom and just dropped a positive and negative on a standard servo plug, and powered the vario on the other end from scruffy through the normal servo connections. I use a 1S Lipo to power everything and that works just fine. I hope that helps.

Should't one programm the ailerons going up (1mm) for start position?

@lotophagi711

4 жыл бұрын

Hi, It's normal to have a little positive camber for the initial rotation. Once the momentary switch is released after the DLG starts to climb the reflex (negative flap) is put in for the "zoom" mode. You can see that at about 3:30 in the video. Hope that helps.

Do you have any videos about programmig transmitter for your setup? Or maybe you can direct me somewhere where I could find that info? Just starting with OpenTX so it is still a big mess for me.

@lotophagi711

3 жыл бұрын

Sorry I don't have any videos on programming it. I just used online resources like this rc-soar.com/opentx/basics/index.htm

@rehepeks

3 жыл бұрын

@@lotophagi711 thanks, will check.

Personally i would use reflex on launch with a dlg.

@lotophagi711

8 жыл бұрын

Yes reflex is used in the zoom phase of the launch. When the momentary switch is pulled a bit of positive flap and up elevator is added to help the rotation. This is only held on for a second until the plane has rotated. As soon as the switch is released the up elevator is removed and reflex is added. I think this is clear in the video and is pretty normal stuff:-) If you watch the launch at the beginning of this video kzread.info/dash/bejne/jIub3JSLeZeokbQ.html you can see it starts wit positive camber and goes to negative as soon at it leaves my hand.

@kyus1974

8 жыл бұрын

+Lotophagi You will gain a couple of meters if you use reflex all the way up, then camber as you push over. This will reduce your stall speed and maximize launch height. If your cg is near the neutral point then you should only need 2mm up elevator to rotate.

@lotophagi711

8 жыл бұрын

I disagree. I have experimented with the setup a lot and get better launch heights with a momentary bit of positive flap to help the rotation. With the CoG where it is I need a tiny amount of elevator to start the rotation. This is varied depending on the amount of wind and the launch angle required. The push over at the top is helped by negative snap flap - not adding more positive flap! It needs to behave in the same that an aerobatic plane does. This is pretty normal practice for a DLG. I have experimented carefully with this setup to optimize launch height and is normal practice in Europe and Asia.

which spektrum reciver are you using ?

@lotophagi711

8 жыл бұрын

I'm using Frsky D$R-II with their Vario and a 1S 1200 Lipo

Sir, I enjoyed that simple setup, I've just transitioned to a Taranis Q X7 and would love a copy of your file. If you are still monitoring this video just acknowledge and I will check back and include my email. I'm currently on OpenTX 2.3.---- not sure the last # but even if your file is for an older version I could probably open it in companion and learn. Or adapt it. I'm mostly interested in the switching from launch to other modes when the launch switch is released. (or even a similar one if you have moved on) I'm flying an Azure, similar to the Topsky 1 I think. Thanks, Alex

@lotophagi711

4 жыл бұрын

I haven't updated the setup since 2016 - unfortunately illness has prevented me from flying for the past 3 years. I can send you the .eepe with pleasure if you send me your email. It's based on version 2.0.20 but that shouldn't matter.

@Sandromonell

4 жыл бұрын

@@lotophagi711 Thank you so much, and sorry to hear about your illness! My email is mhcadroom@gmail.com

Nice Vid! I too would like to receive your setup file. Much appreciated!

@lotophagi711

8 жыл бұрын

Sorry for the delay I have sent you a copy.

@lotophagi711

8 жыл бұрын

oops - I need your email address?

@Arthur_C

8 жыл бұрын

not sure if you got my previous message: please send to arthur@plaatjesmakersinc.nl

Where could I get that dlg?

@lotophagi711

6 жыл бұрын

www.rcgliders.cz/letadla/maat-f3k/ He also makes a carbon wing version which if you are a strong launcher would be good idea I think.

@phil36135

5 жыл бұрын

rcgliders.cz/letadla/maat-f3k/

!!!

Hi... Enjoyed your video. Appreciate if you can send me a copy of OpenTX setup for the DLG .. this is exactly what I want to follow .. thanks

@lotophagi711

2 жыл бұрын

Happy to send you a copy - although the code hasn't been touched for years... But I need toknow where to send it.😁

they are sold out!!!