The beauty of youtube is interaction.. you show us your world, we bring experience from ours...we all learn...

@MiniMachines1

4 жыл бұрын

Yes it's awesome, get so much great feedback with good ideas 😁👌

You know the saying; If it's already broken, you can't mess it up any more... And you might as well make it temporary permanent. Thanks for the nice entertainment. ;-)

Nice job.

thanks for sharing !!!!!

@MiniMachines1

4 жыл бұрын

My pleasure!!

👍Get it done. In order to keep it going. I like it. Replacing parts anyway. 🍺🍺 after that.👍

@MiniMachines1

4 жыл бұрын

Thanks, yes if there is a way to continue working safe I will try that. Up here parts normally is a week away so no need sitting waiting on that 😊

Heineken is a good lubricant..to mind and body..😁

Befor welding this cast iron arm, you should take it off first and check if this pivot shatf got teeth, cause if they are worn out it gonna brake again .

@MiniMachines1

4 жыл бұрын

Yes shud have done that but was in a hurry had customers waiting on me so I just went with the quick fix worry about it later 🤗 since I had found used parts to fix it, this fix is just so it will hold until than 😊

The left looked out of adjustment to me ! Who makes that Velmat tractor ? What country is it from Norway maybe ?

@MiniMachines1

4 жыл бұрын

There is no adjustment on the left side only the right side. The valmet is made in Finland 🇫🇮

@davekimbler2308

4 жыл бұрын

Mini Machines your saying there’s no adjustment at all on the left side ?! That don’t make sense, both sides should be adjustable ! My tractor has adjustments on both sides !

@MiniMachines1

4 жыл бұрын

@@davekimbler2308 no the left side is fixed and the right side have adjustment.

Did you grease the seal before you slide it on? That spline shaft would be hardened and you won't be able to weld to it properly.

@MiniMachines1

4 жыл бұрын

Did spray it with silicone, my main goal with the weld was to keep it in place so it won't tilt out. And that it last until the new/used parts are here, so hopefully it will stick til then 😊

Yikes, that will keep you running, it will in the end make it more work to remove lifting arm off rock shaft.

@MiniMachines1

4 жыл бұрын

I'm hoping I can release the arm on the other side and than push it true🤞

Those splines in liftarm axle and liftarms are weak spot -05 series Valmets and some younger models when they are start going loose , there is no any good strong fast repair. If that liftarm axle slides sideways , it can broke or bendt inner parts for lift control valve.

@MiniMachines1

4 жыл бұрын

The list controller haven't worked since I got it, if I lift the 3 point all the way up the pump continues to pump so I guess this is nothing new. I will get a used axel and lift arms so hopefully that will fix it 🤞

@MrJsormunen

4 жыл бұрын

@@MiniMachines1 Something is not right there if pump does not stop makin pressure when 3point goes uppest position , if those trailerhitch lift telescopes are too short , it also causes that continuous pressure in 3point top position , also it can be inner proplem. In -05 series , in factory they make younger moldels liftarm axle threads both ends and instal cup style washers , that lockring is not the best option to keep arms in axle. When you instal new axle and arms , clean splines and reassembly whit tar or anything what stops rusting.

@MiniMachines1

4 жыл бұрын

@@MrJsormunen will check inside when i take it apart, but like it's been and is now its when I get almost to the top it continues to pump, I actually thought something was terrible wrong once out clearing snow, when driving I was missing a lot of power and I thought it was something with the engine, but that I realized it was the 3point list being too high so the pump was running 😏