I have really enjoyed watching your videos. I’ve been in the game 43 years but I’ve never had any formal training for breakdowns other than a couple of Vaillant courses. I have been concentrating on installs, bathrooms and general plumbing. Thanks for all the tips they have been very useful. I have seen a few on KZread and I think yours are the best. Some I’ve watched hardly know more than me lol. regards Clive.

@HeatingGeek

5 жыл бұрын

Thanks. It means a lot from someone who has been in the game as long as you!

Great video again pal, liked the "get it going if you can" attitude, as that's what I aim for, especially for the elderly in colder times.☀ Keep em coming fella👍

@HeatingGeek

5 жыл бұрын

Thanks. It wouldnt be in the menus they didn't want you change it.

That was smart moves Ollie. Experience and understanding is key and you came good as usual.❤

@HeatingGeek

4 ай бұрын

I wish I had this video in better quality.

Thanks for that. I think they must have been working on the main nearby as the properties are so close. I did try the old hit the gas valve on both but they wouldn't move. I wished I'd kept the gas valves to look inside. Anyway thanks a lot and enjoy your day.

@HeatingGeek

5 жыл бұрын

Thanks. Have a good one!

Great video, love watching them all, some great tips, even the vailliant course don’t exsplain fault finding that well, good work 👍🏻, where do you get all your literature from if you don’t mind me asking? Do you have it for all/most boilers you work on? It’s a simple but very clever idea to always have something like that to hand,

@HeatingGeek

4 жыл бұрын

I didn't see this comment before. Sorry. I have some stuff for the boilers I see the most. I keep set up guides from gas valves because this can save a lot of time on site, :-)

Hi Mate, Great Video, I had the same fault today, I thought it was a pump fault and ordered one to go back to fit it tomorrow, ill try this option first to see if it works and to save them some money, I can hear a bit of air in the boiler but having a bit of trouble clearing it, the auto air vent is working though ?? Any ideas ?

I’ve had something similar to this in the past , as it wasn’t set up correctly from install. I found I had to adjust the bypass and increase pump speed in d.19. Most engineers would be thinking either pump issue or it’s blocked somewhere.

I cannot thank enough for the knowledge u r sharing with us. Everyday i am learning very good tip. Very detail and interesting. Much appreciated. Regards

@HeatingGeek

4 жыл бұрын

No problem. :-) Glad you like them.

@samtenlobsang9015

4 жыл бұрын

@@HeatingGeek good morning mate. Can you please tell me where i can get/ download the reference chart you have got. I work mostly on vaillant boiler. That will be very handy for me. I will much appreciate. Thanks. Have a good day.

@HeatingGeek

4 жыл бұрын

@@samtenlobsang9015 I have it on my Patreon for my Patrons. It took me many years to get it together. www.patreon.com/heatinggeeks

@samtenlobsang9015

4 жыл бұрын

@@HeatingGeek thank a lot mate. Have a good weekend.

Hi Maty . Hope you well what did to that boiler to be honest just gentle tapping on the set annoyed of the gas valve and the open up again the gas valve and the boiler started working Boiler from what I’ve heard it’s been moved to a different location is why am I think the gas valve had some air in it just purged the line .. no error codes display I thought I’ll give you an update

@HeatingGeek

5 жыл бұрын

It will come back. I have done that several times and they always come back. I had no broadband for 5 days so couldn't reply.

I rate you your methods and logical approach to fault finding.

@HeatingGeek

4 жыл бұрын

Thanks :)

Very good diagnostics, keep up the good work.

@HeatingGeek

5 жыл бұрын

Thanks.:-)

Great vid as usual. Looks like the older Wilo pump before they switched over to Grundfos.

@HeatingGeek

5 жыл бұрын

Yes it is!! Good spot. Thanks for watching and commenting. :-)

I liked the video before I even watched it lol. Keep up the quality work mate.👍🏼

@HeatingGeek

5 жыл бұрын

Thanks :-)

@woodbine66

5 жыл бұрын

Yep same here. Know it will be a good 'un before it starts. Thanks HG!

@HeatingGeek

5 жыл бұрын

Thanks :-)

@HeatingGeek

5 жыл бұрын

woodbine66. I got a couple of good Worcester Vids coming if I can get them edited.

Why is the boiler going off and on with the hot tap running should it not be constant. If it is fixed.

@HeatingGeek

5 жыл бұрын

The tap is only running 3Litres per min so the boiler needs to go off to keep the temperature at the set point.

Hi , I’m confused if there is power to the pump and it’s not spinning surely that’s a faulty pump ? What you did works but not as a permanent fix maybe just to see them with hw till the pump gets fitted ?

@HeatingGeek

4 жыл бұрын

No, It will work constantly. The pump has 2 windings. One high power and one low power. I have just told the boiler not to use the low power winding (because its failed). The boiler will only use the high power one now. Obviously, the pump should be replaced but it will work fine until then. :-)

Any ideas water goes cold. I have a Vaillent ecomax 835e a with status S53 when DHW demand S14 up to temp them flame shuts off and S53 ? great videos very helpfull. David

@HeatingGeek

4 жыл бұрын

Blocked plate, blocked main heat x, slow pump or blocked rubber pipe.

@dbrownscombe

4 жыл бұрын

HeatingGeek I changed the rubber tube 4mth ago as the same fault was happening, checked new rubber tube and it’s clear.. (the Combi boiler is 10yrs old) at that time I changed the plate exchanger and both sensors, to the MHExchanger. The pump is set to Auto in settings, I tried high rate, but no change. 2yrs ago I fitted a magnflow in line filter on the return CH pipe. Do you think the small in line filter from the MHE could be the issue on this ecomax (Plumbase part No - VAI07-4517 -4517 FILTER, ) any other ideas? so annoying as I’ve just fitted a new MHExchanger (as it was perforated and losing pressure) now got this DHW going cold issue back. I don’t what to have to call out the local Vaillant expert after getting this far. Cheers D

You are doing great mate, keep up . Can you give a copy of that list you were looking at the fault codes please.

@HeatingGeek

5 жыл бұрын

I tried to get a photo of it but its too shiny!! Keeps getting glare all over it! If I can find a paper copy I will upload it.

@asengogov1295

5 жыл бұрын

@@HeatingGeek please do mate, if you can just email it to me please. gogov@hotmail.co.uk

@HeatingGeek

5 жыл бұрын

I cant find a copy!!

@frosty_soda

2 жыл бұрын

@@HeatingGeek what's the name of the fault codes list?

Once again top upload mate... Just wanted what paperwork was that and is there anyway I can get a copy 👍🏽👍🏽👍🏽

@HeatingGeek

5 жыл бұрын

Thanks. :-)

@HeatingGeek

5 жыл бұрын

I cant find them!!

@famztsb

5 жыл бұрын

HeatingGeek damn! if you find them can you send me a copy

Can you do a video of the tool roll and what tools have in it ?

@HeatingGeek

5 жыл бұрын

Im doing that video at the moment!!! Very soon.

@heatservicebwcuk1545

5 жыл бұрын

Pepper spray 😂

I should watch this video many times,it’s got good tips

@HeatingGeek

4 жыл бұрын

Its a bit quick but shows the info. :-)

Thanks for the video May ask a question? So i understand that the pump was not alternating to high speed. Is it someone set it to low speed. And you have locked to high speed. Or is it because its not alternating to high speed and thats why you set it to lock speed Love your video for us beginner

@HeatingGeek

5 жыл бұрын

The PCB controls the pump speed. It used high or low when it thinks its appropriate. Low for Hw when burner is off high when burner is on. The cheaper (Pro) version only has a high speed pump so costs a VERY small amount more to run. All I did here was to Force the PCB to use the pump at full speed all the time. Because the low speed winding had failed and the pump would stall when it was meant to run at low speed. Im glad this helps people. :-)

@Taqqiyastar

5 жыл бұрын

HeatingGeek Thank you i was thinking the same Love all your videos what you doing is great than a training centre

How did they repair it in the end mate new pump? My guess was them black rubber hoses mite have been blocked was there any F code

@HeatingGeek

5 жыл бұрын

It was just the high speed pump winding failed. The customer said the boiler was fixed the next day!!! Before anyone went back. Locking the pump on high hides the issue.

@felvino7

4 жыл бұрын

If the high speed pump windings had failed would that then not allow the pump to be forced into high speed.. The fault was there was no power from the board to the high speed side of the pump until it was forced?

Omg olie. I went to a vaillant yesterday same eco tec with the knobs. Went there to do a gas cert but agent told me to check hot water for tenant as they can't seem to have hot water long enough. Anyway, when I got there heating was already on so away I went and opened up the hot water tap. Hot water came on, had my eye on the flame never went out but hot water went lukewarm and stayed lukewarm. I did notice the flame diddnt seem as strong but it diddnt go out!! I felt the plate heat exchanger and it was cold! I also assumed the diverter might be letting by so I isolated the flow and return thinking the hot water will suddenly get hot. No Luck! I'm due back there but I was going to flush the plate. I will now do this instead as I assumed the pump was fine as I felt it spinning.

@HeatingGeek

3 жыл бұрын

What was it?

@jerrickcajigas3113

3 жыл бұрын

@@HeatingGeek landlord decided to replace in the end as he wanted a boiler with long warrenty. But from your video im pretty sure it was the pump. Had 5 cables from pump aswel.

You are really very very good Ingenir I like it your work really good details on there thank you

@HeatingGeek

5 жыл бұрын

Thanks. I have a few more good videos coming

Great video, is the list of Vaillant D Codes something you made yourself or is it able to download anywhere? Thanks

@HeatingGeek

5 жыл бұрын

I had it on a file somewhere but haven't been able to find it. I promise if I do I will have it for down load.

@samgould1268

5 жыл бұрын

Nice one thanks. Keep the videos coming, I'm a newly qualified heating engineer and like to watch to gain knowledge and tips 👍

@sandraallsopp1234

5 жыл бұрын

HeatingGeek could you scan any codes sheets you have so we could access them as they are massively helpful.

Excellent. Thanks for posting.

@HeatingGeek

5 жыл бұрын

This could of been a better video but hopefully most people are able to get it. It really gets you out of trouble though. :-)

I know., but in this case the boiler only two years old ., i did advise that is still on warranty but ., Customer wanted me to fix it right there and then., Ta mate .,

I’ll watch out for it matey top man

Perhaps it would be good to point out & not forget the Golden Rule of SS plate heat exchanger circulation: The Return from the plate should always be the same temperature as the Hot Water supply. HG has an intermittent fault here on Hot Water, very difficult to diagnose.

@HeatingGeek

5 жыл бұрын

Thanks ;-)

Affix on the first visit Customer is happy and no time wasting

Hi I have a velliant eco tec plus 831. I have problem with hot water. When I on the hot water tap hot water coming but after two three minutes hot not coming when I checke the boiler not working fast it's work slow. So I clean the heat exchanger. But still same I checked both ntc but still same any idea wating for Ripley thanks

@HeatingGeek

5 жыл бұрын

S code?

@zakp1326

5 жыл бұрын

@@HeatingGeek thanks for Ripley. No I haven't done with s code could you please tell me how to do it with s code

@zakp1326

5 жыл бұрын

Display not show any s code

@HeatingGeek

5 жыл бұрын

@@zakp1326 Use the MI's to find S codes. Which ecotec is it manual CO2 or auto CO2?

I would like to ask you your opinion on these two jobs. I don’t do many breakdowns but one was my nephews and the other was a service that turned into a repair. These jobs basically ran consecutively because of times of visits getting access and parts. First one EcoTec 630 about 6 years old but not been registered for guarantee, second one EcoTec plus 831 not been registered same age. 635 has a F75 fault pretty easy to diagnose pump not running with power to pump. Change pump starts to go through ignition sequence only to not light despite sparking. Then goes to F54 and F29. I am like I can’t believe this. So check gas valve for resistance 150 ish. 22 volts dropping to 16 on the lead. On the Yellow lead holder did resistance and 116 ish if I remember correctly. I ring Vaillant they say all the readings are ok. So I do a strip down of main burner it’s really clean put it back together and still not working. Ring Vaillant they say you know it’s the gas valve stuck so change it. Apparently the gas valve has an internal filter but you can’t get at it?? I reluctantly change the gas valve and it works. The 831 was exactly the same except it started with an F22 which was the sensor. Changed the sensor that cleared the F22 only for the boiler to go to you, guessed it F54 and F29. Everything exactly the same with the readings of the Gas valve. I didn’t strip the burner out just changed the gas valve and it’s working lovely. These properties were within a 100 yards of each other. I wondered if something in the gas supply had caused the valves to jam up. I just wondered if you have experienced anything similar or had any ideas as to why that might happen? I understand if you haven’t got time to reply. Clive

@HeatingGeek

5 жыл бұрын

The valves are susceptible to the black dust you get in the gas mains (Copper sulphate I think). It causes the rubber of the valve to become sticky and the valve wont open. Very common on these boilers. When the boiler is trying to light if you tap the gas valve you will get it working for a short time. I think the new Honeywell gas valves are changed internally to combat this. Different rubber or Grease i think

@HeatingGeek

5 жыл бұрын

Also the 22 dropping to 16 is normal on all ecotecs new or old!

Hi mate just letting you know your advice about the 99% PCB I’ve turned up with a new one and the boiler is fine I engineers turned up tried replacing many parts

@HeatingGeek

5 жыл бұрын

Good. Im glad you got it sorted.

Do all the modern boilers have this facility????

@HeatingGeek

4 жыл бұрын

A lot of them do. :-)

We're did you get the carts you have

@HeatingGeek

5 жыл бұрын

Vaillant. As soon as i can get another copy I will let all of you have it!!

Pro tip: Pump speed 3 also makes the house phone ring

@matthewwilkinson8289

Жыл бұрын

😂😂😂class

You should have got the Gas Safe Award, thanks for sharing.

@HeatingGeek

5 жыл бұрын

Whats that? I got the registration and im hanging on to it!!!!

Hi mate Any tips on the F54F 28 March appreciated matey

@HeatingGeek

5 жыл бұрын

I will do a video on this fault as soon as i come across it. It going to be the new F75

@benjaminfrost4363

5 жыл бұрын

pcb mate . have changed loads at 8 years plus!

@HeatingGeek

5 жыл бұрын

usually the gas valve. PCB sometimes but gas valve usually.

The capacitor in the pump maybe?

@HeatingGeek

4 жыл бұрын

Maybe. But why would it work on high? I think it might be the windings.

Hi mate I thought I’ll give you an update on that job for my deal logic Combi 24 As I suspected L3t is indeed the PCB ..

@HeatingGeek

5 жыл бұрын

Nice one thanks for updating us all. :-)

Quick way to fix the f27 Maty .. any idea

@HeatingGeek

5 жыл бұрын

PCB fault 99% of the time. I hope your gas safe...

@hadjarramouche9984

5 жыл бұрын

Hi mate just been to check an ideal logic Combi displaying an L3 narrowed it down to PCB am I correct it is an expensive part any thoughts on thatMuch appreciated

@heatservicebwcuk1545

5 жыл бұрын

Seriously ? are you in the trade ?

@HeatingGeek

5 жыл бұрын

Sorry never replaced one. I would guess looking at the fault code that there is no circulation? But I don't know tbh.

@hadjarramouche9984

5 жыл бұрын

Yes Maty , started as air conditioning engineer.. didn’t get much work as self employed.. the. Switched to plumbing and heating, is the best thing. I cover every thing.. am focusing on Repaire..

Don’t worry I am mate

Nice one mate

@HeatingGeek

5 жыл бұрын

Thanks :-)

Annoys me when other engineers turning up changing parts that has no relation to the fault

@tatelandry6740

3 жыл бұрын

I guess Im kind of off topic but does anyone know of a good website to stream new tv shows online?

@alexiskylo8916

3 жыл бұрын

@Tate Landry try Flixzone. You can find it by googling =)

With you method of working, you gotta be ex BG? Great videos btw, thanks 👍

@heatservicebwcuk1545

5 жыл бұрын

Meaning ?

@HeatingGeek

5 жыл бұрын

No I'm not but I did contract for them for a year. Taught myself I don't think BG would let anyone work on a live appliance holding a phone without gloves!!! Be sacked before you know it!!

Beats me why the 6 or 7 "engineers" who had attend this job before you hadn't delt with the expansion vessel & prv etc, perhaps they have the same title as the broken part "heating knob" ?

@HeatingGeek

5 жыл бұрын

Because they were there to fix "no Hot Water" The secondary issues are not of any concern to them.

@jaxmar88

5 жыл бұрын

But secondary issues very often cause primary issues thats all I'm saying, like leaving preheat on constant can lead to early failure of the plate heat exchanger along with high running costs..

@heatservicebwcuk1545

5 жыл бұрын

Yeah I agree with that , I guess the no hot water issue was the priority for the customer but I’m sure Ollie would appreciate if the other guys could fix what they could and leave him to the main fault. no doubt engiineers just leave it to the next guy to worry about found that a lot on a firm I worked for.

@HeatingGeek

5 жыл бұрын

jaxmar88. I know what you mean. If it was MY private customer then I would bring it all to their attention and hopefully fix it all. (nice little earner). But engineers are worked hard these days and only do what the customer asked for. I do miss the old days of meeting in the cafe and talking about the jobs for the day!!!

@heatservicebwcuk1545

5 жыл бұрын

Heating knob was quality though ! Jaxmar taught me the breakdown side as an apprentice, it was Always about repair before replace and proper fault finding. Only thing was explaining pre heat to customers for about an hour used to send me to sleep and did once 😂

Brilliant video must say 👍 where can I get yellow code from..

@HeatingGeek

5 жыл бұрын

Im working on it. Alot of people asking.

@adamsala9291

5 жыл бұрын

;-)👍

@christopherlyddall9272

5 жыл бұрын

Yeah that yellow code sheet would be very handy!!

@HeatingGeek

5 жыл бұрын

@@christopherlyddall9272 Everyone wants it!!! If could find it I would make a pdf copy and let you download it.

@valkoua

5 жыл бұрын

@@HeatingGeek , Please we would really appreciate it if you upload it.. Thanks

👍👌

Combined

👍🏻

@HeatingGeek

5 жыл бұрын

Thanks. ;-)

Some people don't deserve help. Look at all that domestic paraphernalia cluttering up the boiler area. Got you clambering all over the vegetable racks and packets of light bulbs next to the boiler for you to tip toe around! They should be told at the outset to clear all that stuff away before you even touch anything, the lazy, inconsiderate feckers. I am not an engineer, but always think of how I can make their job as easy as possible whenever I send for one, including a cup of tea! Would love you to do a video on the state of people's homes when you visit and get the word out that you guys deserve some respect. ;-)

@HeatingGeek

4 жыл бұрын

Thanks. :-) I already moved some stuff too. These were nice people just getting ready for a family wedding (I think). So they were a bit preoccupied. :-)

@rafflesnh

4 жыл бұрын

@@HeatingGeek They're lucky to have you!

@HeatingGeek

4 жыл бұрын

@@rafflesnh Thanks:-)

UK boilers always have that "Nokia vibe' on the control panel.

@HeatingGeek

5 ай бұрын

They are getting better and better now. The latest Vaillant looks cool.

Cheers buddy

Why didn’t you fix Heating control knob 1st?😳

@HeatingGeek

4 жыл бұрын

Because that isn't what they called me for. The knob wouldn't stop the hot water working. :-)

Press plus button for quick access to return temp reading

@HeatingGeek

5 жыл бұрын

What do you mean? When?

@Pro-nj4uu

5 жыл бұрын

HeatingGeek depending on software version. From front screen minus button flow temp/pressure plus button return temp. *correction. Plus button is warmstart sensor value ! 🤦🏻‍♂️

Hi do you have a email thanks

@HeatingGeek

5 жыл бұрын

boilertechnical@gmail.com

The silver label pumps are garbage (I think they were Wilo) - known problem on Vaillants - they changed supplier to Grundfoss (black label) pumps which are much more reliable

@HeatingGeek

4 жыл бұрын

I have an 11 year old 837 with the Wilo pump. No issues yet and even if it failed now I would accept that it had done its design life. I don't know why the Wilos failed so much and mine has survived?? Weird.

@unkleoo

4 жыл бұрын

@@HeatingGeek purely speculation - but maybe the bearings in the wilo pumps are less tolerant of dirty water (on systems where there has been a boiler change without a good flush) - and I'm guessing your system has nice clean well inhibited water ? Difficult to tell on a small sample !

@HeatingGeek

4 жыл бұрын

@@unkleoo I do agree with that, but my main heat exchanger is becoming blocked but my Wilo lives on???? I have a long-held belief that chemicals bond themselves to the Vaillant main heat exchanger and inhibitor may not help. I have no proof, just a feeling in my gut...

Sure I saw you walking into plumbs Park Royal last week had white moped with you 👍

@HeatingGeek

5 жыл бұрын

Yep. That was me. ;-)

@HeatingGeek

5 жыл бұрын

I think it was Monday?

@BrosnanEvans

5 жыл бұрын

HeatingGeek yeah was Monday 👍 finally met a KZread celeb 😂

Its stuck

@HeatingGeek

5 жыл бұрын

No the low speed winding has failed

You could’ve just taken the circulation pump ohms reading. It needs replaced, it’s not operating as designed. Still, a good video but perhaps a bit misleading?

@heatservicebwcuk1545

5 жыл бұрын

Fibre Washer hardly misleading just his way of doing it. The final diagnostic of the issue is what matters.

@heatservicebwcuk1545

5 жыл бұрын

Lol you’ve given Ollie enough abuse fibre washer.

@HeatingGeek

5 жыл бұрын

I had been at this property for over 1.5 hours and the boiler had worked fine. Not even one minute of issues. Max rate Min rate etc etc. The pump had worked all the time so I had no reason to test it. Once the fault began I didn't want to turn off the boiler and risk it working again!!! The pump did get replaced (by the original engineer) however, Vaillant allow you to change the setting so it is fine to be left like that. This video is meant to show people how they can get a boiler working (For the old lady etc) until they can come back with the part.

@heatservicebwcuk1545

5 жыл бұрын

Much appreciated

@HeatingGeek

5 жыл бұрын

I don't mind a bit of abuse!!! We all do things differently. I usually diagnose after a lot of other visits and the other guys fit the parts.