V#7: SRF3 & BWR Hub Servicing for Brompton (Trifold)
Жүктеу.....
Пікірлер: 27
@jasonwmc2 жыл бұрын
Your share is fantastic sifu Bartley ... Clear and precise without any hold back... Appreciate all your sharing... Kudos
@beachstart2 жыл бұрын
Thanks for this great video going into great detail! Especially addressing the different types of grease is so useful. But it looks rather complicated for me. I am glad to have a to gear Bromi without hub ;-) I'm looking forward for the videos to come!
@kwokweng76 Жыл бұрын
this is a great video
@lollycopter6 ай бұрын
0:37 Such a smooth technique. No vice grips, no adjustable spanner on the other side of the wheel!
@noleo2 жыл бұрын
Great video. Very thorough dismantling to understand the gearbox. Isn't it easier to remove the whole gearbox first? After removing the gear (see 0:20) but not the nuts, then flip over to the non drive side to unscrew the nuts and the bearing cup(see 5:30). Then flip over the drive side and not unscrew the nuts but the gearbox retention ring (see 4:55 & 7:28). After this, the whole gearbox could be removed from the hub for further dismantling and servicing.
@MichaelSim2912 жыл бұрын
thank you!!
@pauli196810 ай бұрын
Great video. I need your help. I cleaned my new Brompton C-Line after a wet ride. The rear pedal and crank arm will not rotate when I fold the bike up. The rear hub is stiff. I have to hold down the chain tensioner to rotate the pedal and crank arm. So I took the hub apart and put it back together again. I tightened the drive side cone nut hand tight, then backed off half a turn to allign with the locking washer. I put it all back together and it was fixed. But I now have very slight play in the rear wheel. Brompton support tell me there should be no play at all. But if I tighten it, the stiffness comes back. So the bike will not fold properly unless I hold the chain tensioner. Kind regards Paul Nelson
@kittyhawkkt39672 жыл бұрын
The types of grease is very well explained, good. Just a pointer for slight improvement, if someone can shine a light on the small rectangular piece (where the indicator link engages) inside the hub when it’s being explained will be good because it is too dark - cannot be clearly seen. The background noise of some else talking at park in the beginning is also distracting. Overall, a good thumb up!
@williamwu6261
2 жыл бұрын
Noted.. our regular pro camera person not available... video taken by a student...
@hochoonhiong2 жыл бұрын
Hey thanks used what to clean all the nuts and bolts?
@darrenjcl2 жыл бұрын
sifu can do a video on how to install BWR on 3sixty/pikes bike that is using SRF3?
@alfredoafrica9475 Жыл бұрын
This is really helpful. May I ask what size of bearings does the front and rear use?
@pb3workshop-shifubartley516
6 ай бұрын
Pls google you respective hub for info
@carywatmore Жыл бұрын
Excellent - you should conduct bicycle servicing workshops sifu.
@pb3workshop-shifubartley516
6 ай бұрын
I do conduct workshops.. In fact this video is recorded by students during workshop
@fredrick8899 Жыл бұрын
Hi Sifu Bartley, i just got a Brompton A Line 3 speeds, can i use my Pikes 6 speed rear wheel and shifter to upgrade my my A Line to 6 speeds?
@nomerouno91292 жыл бұрын
Do you do servicing for BWR wheel?
@erichotb Жыл бұрын
Need advice, after servicing my M6L internal hub, when I shift to 2nd gear(internal hub gear) it will skip gear when I cycle... Any idea which parts I may have assembled wrongly... 😅
@tdgdbs1
10 ай бұрын
Adjust the pull chain.
@maxcrust25182 жыл бұрын
Hi shifu , you often open & servicing internal hub , may I know size of ceramic bearings fits into bwr front & back ? 😁 , Thanks 🙏
@pb3workshop-shifubartley516
6 ай бұрын
I won't recommend ceramic balls as the bearing races will wear must faster. Ceramic vs steel sanding action, Ceramic wins. Also Ceramic uses very light grease... as a result poor waterproofing and your hub can get rusted.
@LeoL772 жыл бұрын
Hi! how often should this hub be serviced? once every few years or are there any "symptoms" to look out for?
@williamwu6261
2 жыл бұрын
2yrs
@LeoL77
2 жыл бұрын
@@williamwu6261 thanks shifu
@FirstLast-jm4dx
Жыл бұрын
@@williamwu6261 Doesn't that depend on the mileage?
@pb3workshop-shifubartley516
6 ай бұрын
Once a year but always check for free play when general cleaning
Пікірлер: 27
Your share is fantastic sifu Bartley ... Clear and precise without any hold back... Appreciate all your sharing... Kudos
Thanks for this great video going into great detail! Especially addressing the different types of grease is so useful. But it looks rather complicated for me. I am glad to have a to gear Bromi without hub ;-) I'm looking forward for the videos to come!
this is a great video
0:37 Such a smooth technique. No vice grips, no adjustable spanner on the other side of the wheel!
Great video. Very thorough dismantling to understand the gearbox. Isn't it easier to remove the whole gearbox first? After removing the gear (see 0:20) but not the nuts, then flip over to the non drive side to unscrew the nuts and the bearing cup(see 5:30). Then flip over the drive side and not unscrew the nuts but the gearbox retention ring (see 4:55 & 7:28). After this, the whole gearbox could be removed from the hub for further dismantling and servicing.
thank you!!
Great video. I need your help. I cleaned my new Brompton C-Line after a wet ride. The rear pedal and crank arm will not rotate when I fold the bike up. The rear hub is stiff. I have to hold down the chain tensioner to rotate the pedal and crank arm. So I took the hub apart and put it back together again. I tightened the drive side cone nut hand tight, then backed off half a turn to allign with the locking washer. I put it all back together and it was fixed. But I now have very slight play in the rear wheel. Brompton support tell me there should be no play at all. But if I tighten it, the stiffness comes back. So the bike will not fold properly unless I hold the chain tensioner. Kind regards Paul Nelson
The types of grease is very well explained, good. Just a pointer for slight improvement, if someone can shine a light on the small rectangular piece (where the indicator link engages) inside the hub when it’s being explained will be good because it is too dark - cannot be clearly seen. The background noise of some else talking at park in the beginning is also distracting. Overall, a good thumb up!
@williamwu6261
2 жыл бұрын
Noted.. our regular pro camera person not available... video taken by a student...
Hey thanks used what to clean all the nuts and bolts?
sifu can do a video on how to install BWR on 3sixty/pikes bike that is using SRF3?
This is really helpful. May I ask what size of bearings does the front and rear use?
@pb3workshop-shifubartley516
6 ай бұрын
Pls google you respective hub for info
Excellent - you should conduct bicycle servicing workshops sifu.
@pb3workshop-shifubartley516
6 ай бұрын
I do conduct workshops.. In fact this video is recorded by students during workshop
Hi Sifu Bartley, i just got a Brompton A Line 3 speeds, can i use my Pikes 6 speed rear wheel and shifter to upgrade my my A Line to 6 speeds?
Do you do servicing for BWR wheel?
Need advice, after servicing my M6L internal hub, when I shift to 2nd gear(internal hub gear) it will skip gear when I cycle... Any idea which parts I may have assembled wrongly... 😅
@tdgdbs1
10 ай бұрын
Adjust the pull chain.
Hi shifu , you often open & servicing internal hub , may I know size of ceramic bearings fits into bwr front & back ? 😁 , Thanks 🙏
@pb3workshop-shifubartley516
6 ай бұрын
I won't recommend ceramic balls as the bearing races will wear must faster. Ceramic vs steel sanding action, Ceramic wins. Also Ceramic uses very light grease... as a result poor waterproofing and your hub can get rusted.
Hi! how often should this hub be serviced? once every few years or are there any "symptoms" to look out for?
@williamwu6261
2 жыл бұрын
2yrs
@LeoL77
2 жыл бұрын
@@williamwu6261 thanks shifu
@FirstLast-jm4dx
Жыл бұрын
@@williamwu6261 Doesn't that depend on the mileage?
@pb3workshop-shifubartley516
6 ай бұрын
Once a year but always check for free play when general cleaning
i damn scared to open :D