Very informative- made that look easy. Thanks

Thank you. That clarified the install instructions for me, and allowed me to verified my installer did not install it correctly. He wired it hot, leaving it on 24/7 with no relay or air switch.

@michaelheckman2128

Жыл бұрын

Yeah licensed technician installer. Many of them are hacks and are not open to practicing new techniques or using new products. But yet companies like RGF does not recommend DYI installs.

I would like to say Thank you for this video that assisted me in completing my own installation without issue.

Your the man, I'm installing one of these this afternoon, very informative 👍🏿

Just installed my halo led and this air pressure switch. Just wanted to say thank you for putting up this video. Helped me so much! This method is literally the only way to go!

@mofassy

2 жыл бұрын

Hi could you tell me how you did it I am having issues figuring this out

@mofassy

2 жыл бұрын

How did you wire the high voltage transformer wires

@drukkosz2196

Жыл бұрын

@@mofassy have you figure it out? i am looking everywhere for that answer. thank you

When watching install videos, it just didn't sit right with me the way those guys were just wiring it to the board - this seems like the safe way to go, thanks

Few Notes on your video The REME Halo LED is not polarity specific so it does not matter which wire you break. Also the led unit cannot be run continually, this is possible to do with the air switch if the end customer is not educated that they cannot turn the fan to the ON position as the unit will not shut down. the unit MUST shut down to clean itself. If you have a customer who wants to run the fan always on the LED is NOT the unit for them The standard REME is for them. Alternatively they can use a T-stat with circulate mode as that will shut the fan off for a short time each hour. Also RGF does not warranty any of our products purchased online due to excessive fraud (counterfeit units as well as units that have been altered by others)

@randyosborn284

2 жыл бұрын

Joe, Does RGF have training/install videos on the website? I've had the training through Shearer Supply but cannot remember all the details. Also, my new techs need a brush-up from time to time. I hate going to KZread and getting not 100% accurate information. Thanks in advance...

@mofassy

2 жыл бұрын

Do you have any website where we can learn how to install it?

@timzalusky

2 ай бұрын

Does Reme sell replacement parts to those of us that purchased online?

Hey, do you know what the orientation of the air switch should be? Should the inlet and outlet be up or down? The manual has them down and a good install video I saw has them the other way. I ask because my air switch isn’t working with the pressure from the ducts. If I blow in to it, it works. So it’s working, but not with my setup.

Great video, I installed this and the pressure switch works, but sometimes I have to wiggle the positive side air sample tube to get it to work. what would be the issue with this? is it not far enough into the air flow? Thank you.

I just installed my halo LED pressure switch per the instructions and your video. When the fan is on I get 26.8 volts at the reme barrel plug. When the fan turns off I get 6.7 volts at the reme plug. Shouldn't the voltage be 0 when the fan shuts down? Great video, Thanks

@michaelheckman2128

Жыл бұрын

Hey Craig, did you ever figure out the ghost voltage issue?

Hi How do you wire the wires inside the transformer the blue and the yellow to the air switch kit Thank you

Thank you for the great video. I was wondering if wiring the 120v side, to a direct source of power, such as the one you described on your video, would be correct. It seems to follow the same method, such as wiring a doorbell, where the 120 volt side is constant, then the secondary voltage would ring the bell, once the button is pressed. Thanks again.

@drukkosz2196

Жыл бұрын

have you figure it out? i am looking everywhere for that answer. thank you

How would you wire a Halo LED with the relay it comes with instead of the air switch?

So, I installed my halo LED this weekend and opted for the switch based on this video. The green light on the halo is on all the time and I think I can see that the light is on all the time. What could be my issue here? I have verified that I have installed correctly and am stumped unless I am missing something?? Any help would be appreciated!

Having a new Bryant Preferred series 2 stage heat 2 stage cool with variable fan installed and the led halo. From this vid, I asked installer if they were going to use the air switch, they said no, going to wire the transformer to the systems "G" circuit for fan signal so it will only be on with the fan... I don't know hvac, so does that make sense or will that damage the Bryant circuitry? Thanks for any help!

@catdaddy3728

Жыл бұрын

Update: well, that did not work, took 3 trips out, 3 different techs before it now goes on and off with the fan... Installers and techs: hey maybe just once in a while, the homeowner MAY know a little something, MAYBE YOU SHOULD LISTEN. Come down off the high horse you think you are on. Anyways, used a universal air switch, wired to signal transformer to power led. Transformer powered by 120v furnace power source. Airswitch needed adjusting with manometer, plumbed to neg side of switch from return duct. Oh, one last tip to installers: maybe not a good idea to brag about being a perfectionist, when you do sloppy work, make mistakes and have to come back a few times only to be pulled from job to have a tech that knows what he is doing fix your mistake... even that tech on a different simple issue was stumbling a little. Whew, they are out there!

I was going to use an AC current switch instead of air switch. I would like to know what u think about that? Thanks for your video

@geebo47

2 жыл бұрын

You can do that, We allow for that option

Just installed my led halo with the air switch. My question is, does the unit with the light, make a sound when it starts up? Mine makes a sound like a small motor starting up, for a few seconds.

@mofassy

2 жыл бұрын

Hi could tell me how you connected the transformer did you connect it to The EAC? Greatly appreciate you help

@irie4i

2 жыл бұрын

I wired mine with a plug,and it's own power source. The manufacturer says it does make a buzz for 30 seconds. My only concern now is how close is too close, to the heater coils. Being that they are usually in the same area

@mofassy

2 жыл бұрын

@@irie4i thank you for the info This thing is tricky for sure

@mofassy

2 жыл бұрын

@@irie4i it is supposed to make that noise I called the egg and they told me thst

@mofassy

2 жыл бұрын

How did you wire the transformer to the air switch Thank you do much

Do we have to use Reme's air sensing switch for the warranty to stay valid?

@geebo47

2 жыл бұрын

No you do not, there are several options, You do however have to purchase from an authorized retailer NOT an online seller, We do not warranty any online purchases due to the major amount of online fraud and clone units out there

Turning it on and off will short the life of the ballast and light. They are designed to be on unless………. They specify different.

@geebo47

2 жыл бұрын

Wrong, We designed the Reme Led to be cycled in cool and heat and NOT run continually