Very informative! I now have the confidence to try this myself. Thanks

@X8RLtdUK

7 жыл бұрын

You can get them here: x8r.co.uk/universal-bosch-common-rail-cp1-diesel-high-pressure-pump-seals-kit-leak-repair Regards, X8R LTD

this video saved me £180+vat..many thanks😁😁😁

a big help,, thanks

Hi dear, all videos are very helpful.🌻🌻🌻

Wow nice ¡¡¡¡¡¡¡¡¡ muy bien explicado gracias

It's a good video. The only improvement I could suggest is stressing the need for absolute cleanliness.

your videos are very helpful...

@X8RLtdUK

Жыл бұрын

Thank you! - Georgina, X8R Ltd

Saved me 220 thanks

Thank you for the clear and helpful video. May I ask please what is the Torque setting for the T30 torx bolts that secure the fuel pressure regulator?

At 7:00 remember that the ring should be faced with the cone down in the head! Would be nice if you told us the torqu on the axel shaft and sensor too. :-)

@bablapandey8652

5 жыл бұрын

Thanks I need electronic and censer sistum nozzle injector trening. Please Sir help me. +918103950810

how to install to the engine and remove

You haven't replaced the most important thing the brown oil seal located at the exit of the rotating spindle very often the Diesel leak is just the...

What do you call the brass fitting where the pipes go over? Mine is leaking from there

I did this recently and the HP pump still leaked. The fix? I 'milled' the rust off the cylinder heads and mating faces using a piece of glass and 400 grit alox paper. A good clean up and all was well. The vid doesn't show replacement of the pressure regulator O-ring, a very common failure point.

@X8RLtdUK

7 жыл бұрын

Hi, thank you for the feedback. We're always looking to improve our parts, we shall certainly consider the addition of the pressure regulator O-ring.

To whoever is still watching this video in 2020: DON'T use latex gloves to work with diesel, as haydrocarbons break down the latex (that's the same reason why you don't use vaseline as a lubricant on a condom, btw). Better use VITON gloves, or NITRILE gloves when working with fuels and oils.

@X8RLtdUK

3 жыл бұрын

Hi there, thanks for the great tip! - Georgina, X8R Ltd

How do you change the two small o rings on the fuel pressure regulator? One is teflon and can break when removing and installing. Why didn’t you I change these as they commonly fail it seems.

@edenhomesdesign

2 жыл бұрын

Can you order them on ebay? Is there a link please

@comeinhandynow

2 жыл бұрын

@@edenhomesdesign I answered my own question by doing this job myself. My video here: kzread.info/dash/bejne/nmSfp8ewYJi8p5M.html

nice video #mechanicbrother

hello my friend, would you tell me what's the reference number of ball big one! thank you

please I want attend the training course about the fixing diesel fuel pump and injector kindly let me know where I can have the training which learning center

Torque on bolts Nm?

Is car sensor check karna hai jo pump banaye Hain

Price for Fiat stilo Jtd 85kw??

What about changing the shaft seal - simmering ?? It Can leak too !!! ! !!!

@benc911

Жыл бұрын

These do leak. Very often. I've had 2 leak into my engine twice !

@booring2

Жыл бұрын

Where is it?

@benc911

Жыл бұрын

@@booring2 on the shaft. My 1.7 Hyundai was 2 fuel pipes the wrong way around return on the inlet, so pressure was blowing it.

I`d a sudden high pressure fuel leak due to an broken tube. The broken tube is replaced, but no high pressure anymore. How do I restart the fuel pump?

@edgardh9359

3 жыл бұрын

Hey there! Did you tried bleeding the air from the fuel system?

@xtra330

3 жыл бұрын

@@edgardh9359 problem solved. Internal injector leakage. Thanks 😊

@edgardh9359

3 жыл бұрын

@@xtra330 Great news brother! Be safe!

Tengo un Foton 2778 cc Diesel modelo 2012 y ya para prender se debe dar a oler gasolina, remplace la valvula que regula la presion en la bomba, remplace un inyector que retornaba mucho, y nada esperando respuesta. Carlos Hernandez Medellin

@dusanmarkovic4265

4 жыл бұрын

hello there on 09:41 secund,what and for what is senzor?

@vincentrolfe1384

2 жыл бұрын

@@dusanmarkovic4265 That sensor can connect with the ECU and tell it if the high pressure is absent due to the low pressure pump not delivering fuel to the high pressure pump. Mercedes Sprinter has a similar safety that protects the high pressure pump from running dry.

so no need for assembly lube on the drive shaft.?? Just to assist the pump lubrication during the first start.?

@uweeduinkorte1937

Жыл бұрын

they should soak all the internal parts with some clean Diesel, as the lubrication is realised by Diesel

@jasonputtock4428

Жыл бұрын

@@uweeduinkorte1937 yes you are correct. I optted for assembly lube on moving parts until the diesel makes its way into the chambers. Then diesel takes over on prestart for new rebuilds.

@cannaroe1213

8 ай бұрын

​@@jasonputtock4428the issue bro is that fuel systems, petrol, diesel and LPG even, are never rated for anything other than fuel. There are surface coatings on these parts that might dissolve in vasaline lube but not diesel oil, there's positive-displacement pumps squeezing known volumes of oil out of tiny injector holes, it really couldn't be a worse place to put some goop. I mean these Bosch pumps were pretty solid, they can allegedly run on straight vegtable oil, not simply B100 but, like, olive oil. Got to have the right seals and gaskets though.

@jasonputtock4428

8 ай бұрын

@@cannaroe1213 Well I rebuilt my own PUMP and used assembly oil in it. Smeared a thin film over all metal surfaces and the van runs great. Now been running for 3K km and no issues what so ever. Thanks for your reply.

@cannaroe1213

8 ай бұрын

@@jasonputtock4428ay well i learned something didn't i :) thanks for your reply

How much does the spares cost

@X8RLtdUK

2 жыл бұрын

Hi there, here is the link to the product: x8r.co.uk/universal-bosch-common-rail-cp1-diesel-high-pressure-pump-seals-kit-leak-repair.html - Georgina, X8R Ltd

How do I place my order?

@X8RLtdUK

7 жыл бұрын

Hi Mark, you can order at www.x8r.co.uk