You know you're a real engineer when you fire up the homemade vacuum induction furnace to avoid sending an email

@jakobfindlay4136

3 жыл бұрын

It's not so much to avoid the email, it's just usually expensive when a company says contact for pricing so he made his own to save money and because he can

@ARVash

3 жыл бұрын

@@jakobfindlay4136 an email is already too great of a cost

@gasfiltered

3 жыл бұрын

@@jakobfindlay4136 on the contrary, if you have even the most basic appearance of a business or a promising application, many places will gladly send you engineering samples and have an engineer reach out to you to help you design your process.

@hyperhektor7733

3 жыл бұрын

haha most dont know that this crappy behavior was standart in the >2000's , usually if a company didn't list price you could not afford it xD also totally unpractical. Its a method from the 1970's where it was normal to order over physical mail.

@bugdrvr

3 жыл бұрын

@@gasfiltered This is very true and sometimes you can be pretty open about the fact that you're only looking for a few pieces for proof of concept. Years ago I, and a few other people, got a handful of JFETs as samples for projects which seemed to arouse enough interest in the DIY community for smaller distributors to begin stocking.

Chemical supply house: "wont sell to hobbists" Hobbyists: "Hold my vacuum induction furnace"

@sudoscapy9631

3 жыл бұрын

@Lassi Kinnunen Bingo 😎

@bragr_

3 жыл бұрын

Nah he lives in California so he'd probably go for a Nevada corp.

@T3sl4

3 жыл бұрын

"Hobbyist" is stretching it a bit with Ben though :)

@cmdraftbrn

3 жыл бұрын

@@T3sl4 more like mad scientist. but i love it anyways.

@danielforrest3871

3 жыл бұрын

"Hold my Scanning Electron Microscope"

Really interesting stuff. I'm surprised your ultrasonic iron worked so easily just bolting stuff to the front of the transducer. When I've played with them they seemed really finicky about tuning and I think I burnt out two of those ebay driver boards. I guess being so overpowered means they don't have to be performing optimally to get the job done.

@Mitchell_is_smart._You2bs_dumb

3 жыл бұрын

If you two teamed up and brought in Tech Ingredients, you could rule youtube. Please consider it

@AppliedScience

3 жыл бұрын

Thanks! My driver board is finnicky too. I think it helps that there isn't much mass connected to it, and I'm not pushing hard, so it doesn't have much mechanical load. If I build another rev of the iron, I'd use a smaller driver, and a more controllable circuit. I like your new channel logo!

@chain3519

3 жыл бұрын

Unrelated, but kind of crazy, I've been watching both of you since I was in middle school. I'm a senior in aerospace engineering in college now. Both of you have had a positive impact on my life

@OverlandOne

3 жыл бұрын

I just made a similar post above before reading yours here. My company owned two ultrasonic impact grinders and two ultrasonic rotary drilling/milling machines and all of the diamond tooling had to be tuned to a nodal point for the given mass and length of the tool or it would put too much stress on the transducer and the tools would not perform. We machined ceramics and other very hard materials using all diamond tooling. You did not want to burn out a transducer as, even back in the 80's, they cost about $30,000 each. I enjoy watching your videos and always learn something from them.

@BenjaminEsposti

3 жыл бұрын

We've got some ultrasonic press machines at work, used for sealing and joining stuff, primarily plastic. One time, one machine had a bolt fracture on the booster, and it made such a horrible screech that could be heard outside the building, with the doors closed, over 50 feet away! Ear protection is a must! Granted, these machines are about 900W each. They're indeed picky about the dimensions of the tooling, it has to be tuned, otherwise you risk damaging the horn (transducer) or having poor efficiency.

I've used this stuff. Got it from S-bond (you described their 220 alloy), which wasn't much of a hassle, though they sell it for $5/g. I didn't need much, so that part was fine. It's actually possible to brush it on with a hotplate, so I cheaped out and did that, although you need to clean up the surface afterward--I used a fly cutter on a milling machine. I was bonding glass to ceramic, so the thing that got me was the high yield/creep strength. One of the easy ways to cope with thermal expansion as you come down from the melting point of the solder is for the solder to creep a bit, but this stuff has a fine matrix of SnTi intermetallics which act as rigid reinforcement and prevent it from creeping easily. I had a strong alumina piece bonded to a glass piece with CTE 7-8. Everyone will tell you the CTE of alumina is 7-8 also, but that's averaged over either 0-500 of 0-1000 C. Over 20-100 C, the range relevant for this process, it's more like 4-5. So as the assembly cooled, the ceramic pulled the glass apart without debonding the solder; it's got some strength. We learned that we should have stuck with B33 glass (CTE 3.3 ppm/C), which we would have done if not for this red herring about the CTE of alumina. Glass is stronger in compression, so I think the active solder might have worked with a B33 glass part, but we went for a softer solder, and solved some of its problems for our application instead.

I'm starting to lose track of how many times I've seen something on this channel that I would have thought was flat out unrealistic for anyone to be able to pull off in a home lab/shop. genuinely amazed

@Taygetea

3 жыл бұрын

@@JustinKoenigSilica Google X probably pays him at least 300k, so yeah, money helps.

@kyleemmerich2460

3 жыл бұрын

@@Taygetea As far as I'm aware, he basically designed the HTC Vive hardware, so money and experience is a hell of a combination.

@Taygetea

3 жыл бұрын

@@kyleemmerich2460 Well at the moment he's one of the most important researchers in that medical offshoot of X, so that probably pays well.

@stanmacdonald1073

3 жыл бұрын

Well, it helps to have an electron beam microscope in the shop. Oh yeah, built that too!

@aleksandersuur9475

3 жыл бұрын

@@JustinKoenigSilica Money is common enough, that's not a problem. It's much worse, this crap takes time, effort and dedication. Most people doing similar stuff just do it for work and never bother making educational youtube videos out of it.

I worked for the company which developed much of this ultrasonic joining technology, not requiring solder, which was then taken over by EWI. If you'd like to pursue this further and have specific technical questions feel free to reach out.

@sudoscapy9631

3 жыл бұрын

What is your contact info?

@Hexauslion

3 жыл бұрын

@@sudoscapy9631 same question

@otm646

3 жыл бұрын

@@sudoscapy9631 I made an email just for this. ultrasonic.joining@gmail.com

@otm646

3 жыл бұрын

@@Hexauslion I made an email just for this. ultrasonic.joining@gmail.com

@User-nu6km

3 жыл бұрын

@@otm646 thanks

Company: "Contact us for more details" He: "So I made it myself" hahahaha

The Doctor would like his Sonic Screwdriver back when you‘re done with it.

"An alloy that I made myself" -best channel on KZread

@jmac430

3 жыл бұрын

100% agree... @tech ingredients is right there as well, imo. Lol Cheers!

@verdantpulse5185

3 жыл бұрын

Amazing process, and as opposed to most of Ben's projects, I've got almost everything, just need a bit of cerium. I do a lot of alloying, have vacuum pumps, induction furnaces, ultrasonics. Really right up my alley, somehow I never heard of this process. Thanks.

@eldhokurian8940

3 жыл бұрын

@@verdantpulse5185 hi sir any way to contact you I have a few doubts to clear

@WrinkleRelease

3 жыл бұрын

Great comment, and I don't think many think about what sets Ben's channel apart: there are no mid-video commercial interruptions; Ben is genuinely excited about what he is doing and that shows, and he loves sharing information; nothing is dumbed-down. I consider Tom Scott, Captain Disallusion, Tech Ingredients and Technology Connections to be in that same camp.

@MrMilarepa108

3 жыл бұрын

"... by melting down the ingredients in a vacuum induction furnace." Yes!

@ 3:30 ish. it might be helpful also to mention that this principle applies to iron/steel as well. A black iron oxide finish is often used to keep forged pieces from rusting, and a blued (oxide) finish is often used to protect firearms and other mechanical parts where a thicker oxide coating is not desired. These protective oxide coatings just typically don't form on their own like they do in copper.

@SuperAWaC

3 жыл бұрын

rust bluing does not, itself, provide much rust protection, rust bluing is a porous coating meant to hold oil that does the protecting.

@melody3741

3 жыл бұрын

SuperAWaC clockmakers use the bluing to protect the metal. Its not bluing like on guns with a bluing liquid and oil, they literally burn the steel very evenly and it literally turns blue (or straw) and if you do it like that it is not porous and you dont need oil at least as far as i understand.

@SuperAWaC

3 жыл бұрын

@@melody3741 I am a machinist. Any form of bluing (converting the iron to magnetite) is porous. They all require oil to get maximum mileage out of them. What you are referring to is just using heat to temper the metal, the oxide layer formed doing that is extremely thin (the thickness of the layer determines the color due to the way it interacts with light) and largely cosmetic.

@chakflying1

3 жыл бұрын

@@melody3741 Ah, the difference between "Clickspring bluing" and "This old Tony bluing". But I think clickspring do it mainly because the metal needs to be tempered after hardening, the color and protection is just a by-product.

@louf7178

3 жыл бұрын

Good commentary

Ben: The ultrasonic soldering iron is really easy to make. Me: Cool I can built that. Ben: But the ultrasonic solder I created in my vaccum induction furnace. Me: 😵

@user-yp5fp8gn7o

3 жыл бұрын

Doesnt everyone have one on hand ?

@earlspencer7863

3 жыл бұрын

And that's another video which removes the incentive to watch this one

@alakani

3 жыл бұрын

@@user-yp5fp8gn7o I do, got the vacuum pump and variac for 40 bucks at a yard sale and a big transformer on craigslist for 10. Once you start getting or building lab equipment, you can put it together like legos to make whatever you need at the time. Ben has the money and space to keep all his projects assembled and buy new parts but he could have used the same transducer and driver for a number of his projects for example if needed to

I freaking love this channel. The kinds of stuff that has been done on here is amazing and the fact it's being done in a garage is encouraging.

Dang it Ben, I’m trying to sleep! You can just post a video with that title, I’m gonna be up all night!

@johnqpublic2718

3 жыл бұрын

Ditto, Ben!

@Ryan6.022

3 жыл бұрын

Yep I'm already going down the research rabbit hole. Eyeing my parts bin to see what I might do.

@OnionKnight541

3 жыл бұрын

Same boat, man 😅

@matthewellisor5835

3 жыл бұрын

@@Ryan6.022 Sourcing Cerium... Wallet says "ouch"

@AppliedScience

3 жыл бұрын

@@matthewellisor5835 eBay! www.ebay.com/itm/Cerium-Metal-Element-Sample-10g-Chunks-99-5-Pure-Periodic-Table/372414604226?hash=item56b5a3e3c2:g:fSYAAOSwWh1bfypP

"You're not going to make a trailer hitch out of this" haha

@JWH3

3 жыл бұрын

"Hold my beer"

@MandrakeFernflower

3 жыл бұрын

Codyslab: hold my mushrooms

@husker91

3 жыл бұрын

Haha so funny I'm dying

Outstanding video with zero fluff, as usual. You brought attention to many people, myself included, of a technology of which there was near-zero awareness!

I think it could be interesting to test this procedure on bone and stones. They mostly consist of metal cations from the first two groups of the periodic table and the anions are different to those that you have already tested.

@AlanPMatthews

Жыл бұрын

Your question is a little worrying, honestly 😂

@tissuepaper9962

11 ай бұрын

​@@AlanPMatthews just wiccan things

weld a glass box. like a fish tank sealed with silicone but a glass one soldered with that.

@calholli

3 жыл бұрын

Brake a windshield with a hammer and solder it all back together without a noticeable crack. easy money.

@rkan2

3 жыл бұрын

@@calholli That would be great for it, especially if you could just solder the chips... I wonder how reflective the solder is..

@rkan2

3 жыл бұрын

I think this might not work as Ben described the bond is not that strong.. It is soldering, not welding after all..

@nThanksForAllTheFish

3 жыл бұрын

Mechanical strength may be an issue with larger tanks

@pragmax

3 жыл бұрын

@@nThanksForAllTheFish True, but if it's ductile enough it might make a good seal. You could/would use another material for mechanical rigidity, like the upper and lower metal rims of fish tanks provide.

As always, an absolutely awesome video. I need to make myself an ultrasonic soldering iron now. Looking forward to the video making the active solder alloy

@AppliedScience

3 жыл бұрын

Thanks, man!

Super nice! It would be really, REALLY interesting to see this applied to high-vacuum glass-to-metal seals! Would make viewports and electrical feeds a breeze!

Ah yes, another awesome technology that us mortals can only dream of having access to, and indeed wouldn't even know about without this guy spilling the beans.

Any chance of being able to make a vacuum tight connection on glass? For instance making various tubes or apparatus?

@JoshStLouis314

3 жыл бұрын

Good question, that would be a nice way for sealing glass joints if it works.

@noahhoppis2512

3 жыл бұрын

As a follow up, can you use the active solder to prepare a difficult surface (glass window, tube, etc.) then run a conventional pass complete the joint/get a good looking product?

@Spirit532

3 жыл бұрын

Good question - the answer is yes, you can! As far as I am aware, this was one of the techniques used to seal vidicon tube image plates, which needed a full metal ring in contact with a photocathode, at the very front of the tube. You can't really do internal seals though, have to be very careful with how the solder is positioned so as to not create virtual leaks, which would ruin the vacuum.

@Hexauslion

3 жыл бұрын

@@JoshStLouis314 this wouldn't be a great mechanical seal unless you were just trying to be air tight with 0 pressure

@drrrrockzo

3 жыл бұрын

You should look into how copper to glass seals are made...seems pretty straightforward (I've never tried it) and is well documented, but the devil is in the details. I found some old papers online explaining it once. From memory it involves creating a thick oxide layer (but not too thick) on the copper and the oxide layer bonds to the glass.

I love that someone dissaproves of ultrasonic soldering.

That's amazing! Ben, you come with the most fascinating ideas to check into and show us how you made work, I love it.

Blown away. Thanks for making it accessible, because it would have been out of my reach commercially!

New Applied Science! Today is a good day!

@Cadwaladr

3 жыл бұрын

And so soon after the last one.

Ben: Easy do it yourself project! All you need is a small fusion reactor, 2 oz. of anti-mater and a sprinkle of Einstein Bose condensate. Now the condensate may be hard to find so we'll make that ourselves. Lol! Love you Ben :)

@halasimov1362

3 жыл бұрын

😂

You raise the DIY bar for all of us Ben, thank you so much. I want to be you when I grow up (I'am 46 so don't hold your breath or anything).

You're the most amazing and skillful maker on KZread, I'm just blown away by the things you do and your humble way to present. Great stuff, keep it up!

Love to see a high speed microscopic view of the solder in action.

"Oh yeah it's super easy! You just need this, this, this, that, this, that, and this!" - Ben, 20xx

If I remember correctly, while researching how to desolder surface mount components, I found an article that stated that soldering iron tips will degrade over time in continuous use, and it's important to replace the tip every few months. Perhaps if you had converted a much better soldering iron, you may have been able to retain the tip being replaceable, thought I'm certain that would have made the conversion 10 times more difficult.

I had that exact "solder-ate-the-tip" phenomena on a cheap-ass solderstation. Happened with lead-free solder and a really hot temperature (the solderstation temp regulator was exceptionally useless). Felt like it was similar to what gallium does to aluminium.

@N4CR5

2 жыл бұрын

It also happens on copper tips if you use them too high temp and from memory it is some corrosion as certain compounds boil off.

"will solder to anything" *Looks over at cat*

@marceichelsheim1740

3 жыл бұрын

That's an even worse idea than putting a cat in a bath, lol.

@NautyEskimo

3 жыл бұрын

Did you notice his table? He started sticking metal to everything.

@user-yp5fp8gn7o

3 жыл бұрын

Dont u touch that puddy tat. Use something more annoying like welding two cockroaches together.

I find this technique extremely interesting. Two things: 1. would love to see more on your process of making the solder, and 2. would like to see tests bonding aluminum foils to copper wires, as that could be handy in thin circuit prototypes. Great video! Thanks!

@danielmcalexander1314

Жыл бұрын

A while back I was working on a battery charger for a golf cart oddly enough the transformer was made with aluminum wire. I found a special solder that was specified in the manual called Kapalloy9 used with Kapp golden flux work great soldering the copper connectors to the aluminum wire.

I keep coming back to this one while waiting for the next bit of content from Ben. Great stuff and always eager for more!

Very cool. In a rather large tangent to what you tried with the carbon, Robert Murray-Smith did recently do a bit of experimenting with aluminium brazing rods, and managed to get a decent bond between some Grafoil and aluminium. Obviously not a chemical bond, but it may be a relatively straightforward way to mechanically do that.

This is a pretty amazing project. Nitinol on pcb gave me all sorts of ideas for a Carl Bugeja-type project. Someone just needs to find a distributor for the solder, i ain't got time for alchemy. Did you per chance try using the 'soldering iron' for ultrasonic welding of plastics? Might be a nice secondary use.

@user-yp5fp8gn7o

3 жыл бұрын

Oh i like that idea instead of the commercial melters.

This is awesome! I learned a lot from this video, as always. I had no idea that flux was used to remove the oxide layer. Thanks ben!

I used "YT Comment Finder" to find comments about "LED" because I suspected I am not the only one who is intrigued by the reason why the LED blinks. I found more than 12 times this question was asked. It is really a very helpful tool that I will use from now on.

@computermaster360

Жыл бұрын

I just used a comment finder too, searching for "LED" in all caps, only to find that the retraded Google Chrome does not have case-sensitive search... You need an extension or external tool for every basic little thing nowadays.

50 years ago a friend gave me a small tube of a special solder that was also a special alloy that did pretty much the same thing the ultrasonically applied solder does, but 'wetted' and reflowed well using a conventional Weller 60 watt soldering Iron. It was about the thickness and consistency of standard spooled 60/40 resin core tin lead solder and left no visible flux residue. It was coiled up in a plastic tube similar to the 'free' solder sample you often get when you purchase a new soldering iron. I didn't have much use for it at the time, but over the years I used it to solder things I would not normally have been able to solder; such as Nichrome wire (but not the part that could glow red hot), Aluminum, Stainless, etc..... My biggest use for it was repairing solar cells (which were extremely expensive back then, and were always round) It was the ONLY way for me to successfully reconnect broken tabs to the metalized glass on the back,. or to bridge over surface cracks in the tiny treelike pickup paths on the front surface of a cell. I never tried soldering to plain window glass. I never asked my friend for more of it because I still had some, and he passed away long ago. There was a name on the plastic container but I am in my mid 70's and can't remember that name now. I only mention this because you may be able to do some research to find who made it and what was in it now that you know that it did exist,........ at one point in history...

“The problem is we live in an oxygen atmosphere, here.” Damn.

@cobalius

3 жыл бұрын

Nah were already wbout to get rid of this nasty stuff though, just wait for it

smartest man that has a youtube channel. change my damn mind

You come up with more really cool applied physics than I see anywhere else. Every video you upload is a must watch.

Very cool! This really simplifies the soldering process for a lot of metals. No more finding the special flux or technique for each metal!

The sites mention BiSn solder as "active" - have you tried those?

wow thats great stuff... I dont think ill build my own iron but before this vid i didnt even know this tech existed. Something to stash away in the brain box for someday when i have exotic bonding needs ;-) ... Thanks!

@gasfiltered

3 жыл бұрын

There is a giant section of the internet devoted exclusively to "exotic bonding" needs. Just ask the Google.

Love the subtle FU’s to “the man” in your videos!

This Information was very helpful to me. I use indium solder to bond silicon sputter targets. Ultrasonic soldering techniques dramatically improved my process. Thanks!

Next week: "This project requires Helium3. Fortunately, I already built a short-range wormhole generator that allows me to collect some from the far side of the moon."

When this guy says "pretty advanced stuff", you know it's out of your league :p

It absolutely makes sense for the commercial solders to contain zirconium. It is even more active than titanium, to the point that it can react with superheated steam to form hydrogen and zirconium dioxide.

I was going to ultrasonic solder my hand to a famous gallery painting, but I caught the end of the vid. Thanks for the interesting info.

Question: will the 1% gallium in the active solder react adversely with aluminum surfaces? (Or is it in such small dilution, that it has no real effect on aluminum surfaces?)

@meercreate

2 жыл бұрын

Some people have used galinstan (gallium, indium, tin) as a TIM for heatsinks

@jaredf6205

2 жыл бұрын

0.1 percent

@MentalEdge

2 жыл бұрын

@@meercreate Important to note there is that the galinstan makes no contact with pure aluminum in such a use case. All "bare" aluminum quickly becomes covered and protected by aluminum oxide. To get the adverse amalgamation going the surface may have to be fairly seriously damaged, all the while not contacting any air.

@butre.

2 жыл бұрын

@@meercreate generally only done with copper heatsinks, gallium alloys will still eat aluminum

Very interesting stuff. Have you tried putting the substrate on the ultrasonic module and just use a normal soldering iron?

@Tubs737

3 жыл бұрын

If I remember right, the manufacturers recommend exactly that as an option.

Wow! This is amazing, I never knew this kind of soldering/joining existed. I'm absolutely fascinated.

My god, your channel is the most underrated in all of KZread.

@cmccoy3972

3 жыл бұрын

Underrated because so many are undereducated.

Awesome video as usual. You asked for suggestions for applications, I might have one: would it be possible to make an hermetically sealed metal feed through in glass or ceramics in this way? For example by applying the ultrasonic energy to a copper tube from one side while inside a hole in a glass plate and at the same time heating it from the other end and applying the solder? Metal seals are known to be completely hermetic to moisture / gasses and this technique would be very useful in vacuum systems for making a quick hermetic feed-through.

@Tubs737

3 жыл бұрын

This is exactly why I happen to have some of this stuff. It's often used to form a hermetic seal between titanium and sapphire glass. Maybe Ben has been playing with the surgical robot at work.

@MetaJamm

2 жыл бұрын

Keep in mind, If materials thermal expansion are not the same, sealant can't be stiff, or it will not work at all.

Water cooled and induction heated tip for the next version?

Fantastic video as always! Could you perhaps look at developing a simpler alloy which could be ultrasonically soldered under a shielding gas?

I wondered about this when i was trying to make vacuum feedthroughs years ago. very interesting to see it done!

Have you tried using this for glass-to-metal seals for vacuum stuff? Would be REALLY handy!

@Mr.Unacceptable

Жыл бұрын

I wonder if you could solder a canning jar sealing ring onto a glass jar through the ring? Would you have to have contact with the solder and glass or the transducer is powerful enough to penetrate through. Don't know what purpose that would serve but neat to find out.

Incredible stuff! Every video of yours never fails to blow me away. By the way, I can almost guarantee that the erosion of the tip is simply due to the horrifically cheap quality of that iron. I bought the exact same one a while ago and it shocked me how quickly the tip fell apart, honestly the worst iron I've ever used.

@InssiAjaton

3 жыл бұрын

Scrap Science What I learned way back when was that ordinary tin/lead solder eats copper tips of soldering irons. To overcome that, you coat the tip with iron. OK, supposedly all soldering iron tips since that revelation have been iron coated, with copper inside for adequate heat transfer.. BUT, when the coating fails, as it eventually does, at least my soldering irons at some point stop heating the tip. Then I find that they have become HOLLOW!. No more copper, no more heat transfer...

@m8onethousand

3 жыл бұрын

@@InssiAjaton so that's what happened to my cheapo chinese soldering iron.

"Ultrasonic soldering" didn't even know it was a thing, thanks for this great video.

Unbelievable! You're a magician, on every single video of yours that I've watched. And I've watched most of them. Thanks Ben!

try dissolving the solder off the glass slide with acid to see if the soldering processes actually etches the glass

aluminum welds to glass in a vacuum chamber. i had a guy re-aluminize my primary & secondary telescope mirrors he made is own vacuum chamber machine with a titanium filament & aluminum foil from walmart can do up to 17" research grade polished mirrors. he had to use a acid to remove what was left of the old it was well embedded in the glass and i could'nt get it off

I found out today that old air-cooled engines have parts cast from magnesium. After some research I found that is easier said than done. There was almost no information on anyone having successfully performed that DIY. For light and strong metals with excellent heat dispersion properties, magnesium looks really good.

Great. Plus introduction to the xrf scanner. Nice!

12:38 did you just reveal their exact recipe??? XD XRF guns are magic

@davidliddelow5704

3 жыл бұрын

That gun just looks made to ruin so many industry secrets its amazing it exists.

@doctorbobstone

3 жыл бұрын

@@davidliddelow5704 if a group with resources wants to know the composition, I assume that the XRF gun is but one method they could use. That is, I assume you basically can't keep something like this secret. But that thing might as well be a tricorder. It's pretty cool that it exists and is instantaneous. (And the sci-fi sounds still amuse me... 😁)

@senselessnothing

3 жыл бұрын

the building process is often the harder part

@cleverca22

3 жыл бұрын

@@senselessnothing yep, just look at the special glass he made a while back the ingredients you put in have to be wildly different from the final glass mix, because of all of the reactions that happen when cooking it

@CoreRopeMemory

3 жыл бұрын

@@cleverca22 Exactly, the recipe is just the first step

"I wonder what Ben's been up to..." *Uploaded 3 minutes ago.*

@bigdippervizionzjr5479

3 жыл бұрын

Being of course

The mad scientist. You can make anything in that shop of yours!

i don't care what you're planning to do, just do more of it, every single video on this channel is awesome!

You come up with great ideas for videos.

Can you make a circuit board on a pane of glass with this ? I tried to use “copper mirror” chemical reactions for ages and it didn’t work.

@SolarWebsite

3 жыл бұрын

From video it looks to me like you could.

@Khrrck

3 жыл бұрын

You'd need a reliable way to make traces in the conductive coating on the glass. Either etching it off somehow or masking during application.

@km5405

3 жыл бұрын

if you mask the glass with a solder resist mask you might be able to just paint it on. or paint a thin layer on and etch the excess away.

@VicVlasenko

3 жыл бұрын

> I tried to use “copper mirror” chemical reactions for ages and it didn’t work. Have you tried other metals, like silver or mercury alloys? Or use regular modern mirror, which uses aluminium?

@Khrrck

3 жыл бұрын

Conductive glass is usually sputtered or vapor deposited right? Or am I misremembering?

Спасибо друг, очень давно ищу тему ультразвукового паяльника за дешево, все понятно и доходчиво даже с моим плохим английским)

Neat, reminds me of ultrasonic wire bonding used in ICs and RF circuits, but on a macro scale.

I wonder if the solder is bonding to the graphite, but the flaky surface is just giving way under low load.

@simonblackham4987

3 жыл бұрын

How about soldering into a (through) hole to give mechanical strength?

How do they even come up with stuff like this? Such an obscure process, where did they even start?

@QuantumFluxable

3 жыл бұрын

ultrasonic welding maybe which seems to have a bit more direct path from mechanical welding on the tech tree

@firstmkb

3 жыл бұрын

I think it starts with "I got an idea. Hold my beer."

Greetings to you from Russia bro !!! Thank you for a simple and understandable soldering iron scheme, in Russia these cost about $ 4000. Now I can assemble one myself for my experiments, also thank you for the composition of the solder for the soldering iron. The metal analyzer is expensive and I'm impressed you have it. You are unreal cool🇷🇺❤️

@DS-un4kk

Жыл бұрын

Привет! Ты разобрался с плавлением припоя? Какая температура разогрева и время выдержки?

This gives me an awesome idea! Imagine using the solder in a 3d print setup! Extruding solder instead of filament. You could print a circuit board on glass.

@heavyc5790

2 жыл бұрын

Maybe mill the traces using a thin graphite sheet the use this method and make them neat as a template?

Ben, I genuinely need to thank you so much for this video. I had never seen this technique before, and it's so simple. I wish I had seen this 4 years ago when I was working on a research project that required soldering to doped silicon -- we ended up using this weird proprietary compound called nickelex instead, and it was a disaster and our contact quality sucked, and this was despite the fact that said compound was 1% HF acid. This is so much simpler and safer... I'd be really really curious to see if you get good ohmic contacts across silicon oxide -- if you could do a quick IV sweep to check I'd be /extremely/ grateful. I'm also really curious if that silicon wafer holds up to a post-solder anneal, and if it improves the contact quality at all. Again, thank you so much for this!

@absalomdraconis

3 жыл бұрын

I believe that ultrasonic welding is the norm for silicon?

@hedgeberg

3 жыл бұрын

@@absalomdraconis I've never heard of ultrasonic soldering being leveraged within a semiconductor engineering context prior to this -- usually, within that context, affixing anything to silicon via methods other than wirebonding to pads is out of the question. The goal of this project was solid state sensor fabrication outside of a clean room, which restricted the options pretty significantly. I'm sure this was an option that was known at the time, but neither my teammates nor the professor we were working under knew about this possibility ahead of time or stumbled upon it during our research. Dunno if that means we just missed the right sources, if it wasn't as widely adopted at the time, or if it's a research siloing thing.

@absalomdraconis

3 жыл бұрын

@@hedgeberg : Not ultrasonic soldering, ultrasonic welding. I understand it to be _the_ norm for semiconductors, using gold wires that are ohmicly bonded to contact points on the semiconductor die via ultrasonic actuators of some sort. I have neither training nor experience in this field, so I might be misunderstanding something about the whole subject (for instance, maybe the bonding is actually to pre-deposited solder instead of directly to silicon?), but I've run across mentions of it intermittently for years.

Very interesting! Can you tin a surface with active solder, then use regular solder to connect to the tinned area? Perhaps you could use PWM to decrease the ultrasonic power? Is your soldering tip made of aluminium? Gallium would dissolve it (although maybe not when alloyed). ITO would normally be bonded to by first masking and using PVD to add Ti-Au bonding pads. That's how we did it, anyway.

I love watching your experiments and deep dives. Could you do a video on tips for researching papers? Most stuff I find is blocked behind a paywall.

looking forward to the induction furnace video, great stuff thanks :D

Cool!

Putting that xrf gun to good use! Great video Ben!

@AppliedScience

3 жыл бұрын

Thanks so much!

Every time I watch one of your videos, I think to myself, this guy is pure genius.

"Nooo you can't just use sound to bond materials together!" "Haha ultrasound go brrrrrrrr"

But can I use it to bond with my girlfriend?

@jjhack3r

3 жыл бұрын

Yes.

@JoranGroothengel

3 жыл бұрын

Seems to work best on ceramics, so you'd better get ready for some couples dentistry

@mohammedsaad3503

3 жыл бұрын

try using flux next time😂😂

@glasslinger

3 жыл бұрын

@@mohammedsaad3503 Did you mean "fucks?" (sorry, couldn't pass that up!) :)

@AdamAvacado

3 жыл бұрын

​@@glasslinger Hey I watch your videos. Nice content!

More people need to know about this channel.

YES! Super awesome! This is exactly what i need!

You need at least a mili-paul of flux

Lol “sodder”.

@TheGinGear

3 жыл бұрын

That's how you're supposed to say it though? "ˈsädər" oh lol, it's an American thing

@alberthofmann420

3 жыл бұрын

Lötzinn.

@christianbuczko1481

3 жыл бұрын

@@TheGinGear its spelt solder... and that "L" is not silent... i wince every time i hear americans say that.

@TheGinGear

3 жыл бұрын

@@christianbuczko1481 Your personal opinion doesn't affect dictionary definition

@christianbuczko1481

3 жыл бұрын

@@TheGinGear its the ENGLISH language, and the ENGLISH dictionary agrees with me.

Yuss! I love your crazy experiments!

Hi! Can't wait to see the furnace. I am working on one myself but there are some gotchas I have still to figure out. Great vid! Regards, Etna.

first

I found it fascinating having studied welding and metallurgy many years ago. I was asking myself how they actually manufacture the produce the complex alloy solder without corrupting the ratios of metals in the process.

Very cool how you used the hard ceramics tube insulators. Even some of us non-scientists appreciate that.

This Old Tony is gonna go nuts when he sees this.

Tees active soldering alloys are very interesting! I like the idea of playing around myself but I don't have the equipment to do small batches! I imagine a tin lead silver gallium alloy would stick quite well