I might have accidentally said that the system was powered on when the RAM was changed during the live audio portion of the video - if I did, I meant to say that it was plugged in. The system was not powered on. My bad there!

@DustinKleiboer

2 ай бұрын

At 21:05 you state: "the thing that most likely caused it to be broken by that procedure was the fact that Carrie left it plugged in while he did the ram swap" Plugged in, not powered on? Regardless, there are many power states to modern computers. I think we have a tendency to attribute causes that we are familiar with. And therefore I think you are searching for an electrical problem. Have you considered a firmware problem, i.e., that the BIOs is corrupted? As the RAM was removed while the computer was in an unconfirmed power state, and multiple OS levels store data in firmware that is implicated in POST, flashing the BIOs would be a good step to try! You can likely fix it with a USB Bios Recovery, even with Chinese Mini PCs, as they are based upon the Intel (now ASUS) NUC platforms. Enjoyable video. I liked seeing you trace the electronic paths.

@CompHwTipsAndTutorials

2 ай бұрын

@@DustinKleiboer That's a good point about the BIOS, and me focusing on an electrical issue. It hadn't crossed my mind whatsoever, but you're totally right about it possibly being the BIOS

@sativagirl1885

2 ай бұрын

@@DustinKleiboer was an ISO approved grounding strap-on worn?

@SharkoonBln

2 ай бұрын

@@DustinKleiboer True. Shutting down a windows system does not power it down, unless you held the shift key while clicking "shutdown"

@waynemacleod3416

2 ай бұрын

you will have to track back to where that phase is getting an enable signal. (nightmare without schematics) a good channel to watch for that is northwest repair. GPU's use alot of phase enable sequencing. In the end i suppose the lesson is inplug and hold the power button in a moment, before changing components and any system. remember off IS NOT unpowered.

The old saying: It's never the CPU except when it is.

@cheesburger2875

2 ай бұрын

Yes

@jimw7916

2 ай бұрын

the CPUs are the toughest electronic component on any board.

@colinreece3452

2 ай бұрын

@@jimw7916 Agree hence my comment.

@jimw7916

2 ай бұрын

@@colinreece3452 agreed.... Hence MY comment.

@personalPickle

2 ай бұрын

@@jimw7916🤣

Wow I am so so impressed! Carey's channel administrator here - just had to say I so admire your skill, ability to detail all the steps and the fantastic work you did! Just so so good! Fantastic walkthrough and explanation!

@CompHwTipsAndTutorials

2 ай бұрын

Thank you Maralina! I really appreciate the kind words!

@TymexComputing

27 күн бұрын

But who is Carey? - google user id hash ?

@MaralinaDG

27 күн бұрын

@@TymexComputing not sure if you're kidding - see video notes for Carey's channel

@TymexComputing

27 күн бұрын

@@MaralinaDG Oh sorry - i havent registered that these machines were sent from Carey - now i know thanks :)

@MaralinaDG

26 күн бұрын

​@TymexComputing gotcha much appreciated and no worries!

Beelink's problem is 99.9% a BIOS firmware failure. This type of Chinese semi-finished products has catastrophically problematic BIOS firmware. The HDMI output will not work until the OS boots and therefore no communication will be established between the GPU and the display. Try to copy, save and analyze the BIOS firmware, and it will be very good if you can find an “engineering bios”, try to find a similar Beelink and copy the BIOSa firmware and write a new, working firmware to your BIOS chip. Good luck!

@moonrock41

Ай бұрын

Thank you for confirming my suspicions that arose as I listened to the diagnosis. I've become aware over time of how prevalent BIOS firmware failures are.

@GizmoTheGreen

Ай бұрын

yeah a lot of new UEFI firmware especially on some laptops store settings in the same flash chip as the bios. so simpyl detaching battery won't reset bios defaults. change any setting wrong to make your system unbootable and you're fuxked, cause almost no laptops have a "cmos" (more like nvram??) reset button. had this happen on a laptop once, thankfully I had a full flash backup, flashing that also restored my working settings.

@VioletGiraffe

28 күн бұрын

"The HDMI output will not work until the OS boots" - that's just false. HDMI is handled by the iGPU and it works on Beelinks exactly the same as it does on any laptop or desktop. One important thing is that if there is more than 1 HDMI out, only the primary one will be turned on initially. Figuring out which one is the primary is a fun exercise when nothing works.

@kansax8253

23 күн бұрын

@@GizmoTheGreen Had this issue with a craptastic Machinist x99 k9. Adjusted RAM timings, would no longer boot. BIOS battery removal didn't reset the bios, which is a known issue for many of the crap x99 boards. Solution was to buy a flash programmer and write the stock BIOS to the chip.

@joemajortech2657

18 күн бұрын

That is true , most of the problem of beelink from bios🤦

A bit of information for you. The resistor that you replaced with that radial then bridged was probably .02ohms used as a current sense to check that the power button is pressed. Don't worry too much about the ripped pad happens to all of us. Good on you giving it a go. I wonder if the cap right next to that resistor went short and took the resistor out with it before it burned. That could potentially explain the odd solder and the burnt flux assuming someone else hasn't had a soldering iron on it. For the beelink you are probably right that the CPU is cooked although I could be wrong but typically voltage isn't present on the ram voltage rail with the system off. I have never worked on one of these mini-pcs but typically in laptops and desktops the ram voltage isn't a standby voltage meaning it should only be live when the PC enters a powered state.

@CompHwTipsAndTutorials

2 ай бұрын

That's interesting and makes a lot of sense with the resistor! Would you say that's something that should be replaced with a properly valued component or is it something that doesn't matter all that much? I tested the capacitor that was hanging out next to it and as far as I'm aware, it was fine so I think it might have just been the resistor that went. That or someone at the factory had a go at it, as Carey doesn't really do board level repair work. Good point on the RAM voltage as well, I'm pretty sure that the RAM voltage rail in this case was live only when the system was up, though I'll have to double check that when I pull it back out at some point.

@caseycornett5182

2 ай бұрын

@@CompHwTipsAndTutorialsWith the state of that pad I probably wouldn't mess with it. If it is working then it should continue working. I suspect that the whole ram part might be a red herring. I think maybe if some damage did get done it was done on the board itself not from pulling the ram out. Diagnosis of dead CPU might be correct either way although I would probably look at that IC that drives the core voltages. Usually these aren't too expensive and if nothing else this would be a good chance to test out your hot air rework skills after you mess around a bit with other components.

@CompHwTipsAndTutorials

2 ай бұрын

Definitely going to look at some more things on the board in the future, somewhat apart from the RAM issue as it definitely could be a red herring as you said. I was considering going and replacing the power IC on this board, especially because I was also thinking it would be maybe a few dollars at most. However, I couldn't find that chip for sale anywhere! I may have to contact the manufacturer and see if I can get one from them, though I feel doubtful they'll entertain a random guy's request to buy a single chip.

@felixokeefe

2 ай бұрын

It's almost certainly a 0ohm link.

@ServisTOPRO

2 ай бұрын

I am quite convinced that the resistor was only a 0 Ohm resistor used as a jumper. The VGFX line is only active when the integrated graphics card is loaded. Otherwise, the entire CPU is powered by VCORE. It's going to be tense there. S No video output can be a bad ME region in BIOS. You need clean this part of bios but in modern pc is not that simple.Try measuring the resistance on pin 8 of the bios chip.

When I was fixing circuits we would use through hole resistors to replace SMD as a POC all the time. Great job.

@CompHwTipsAndTutorials

2 ай бұрын

That's cool to hear, thanks!

Putting in a POST card and seeing what is completing and where it stops in POST will be the best way to go on these. I have done a number of these this way.

@xumatyt

2 ай бұрын

Is there a M.2 POST card? Or how are you plugging it into a Mini PC?

@drewlarson65

2 ай бұрын

@@xumatyt m.2 is pcie, can always use an adapter

Try this: Connect a keyboard directly to the machine (no kvm switch). And when you turn it on try to press del, esc, f7, enter or other keys. The f7 is the one for entering bios in normal situation. In similar situation, After some trying, I noticed the keyboard started showing life and display also turned on Some of these mini pcs have bad bios and they does not turn display on boot screen even if they "show" a message and waiting for input to continue.

@CompHwTipsAndTutorials

2 ай бұрын

I'll definitely give that another shot, it didn't make the cut but I did give that a go (though I didn't try the F7 key)

try desoldering the bios , flash it outside of system .

@GizmoTheGreen

Ай бұрын

if the vendor supplies a full bios image. some new formats are upgrades only and need to be applied by their flasher onto the existing bios copy. also lots of new uefi bios has device unique keys that you need to dump, and thats if you know where to look and might require sketchy or hard to get softwares...

@domwick720

Ай бұрын

@@GizmoTheGreen where do you find hard to get softwares? forums?i am sure if i was inclined to know i would get them or locate them the same with all illicit things i suppose.

If it were plugged in and the ram was changed without draining the power first, integrated graphics uses your system ram< 31:00 (shared) I can understand how that would effect the other.

For debugging it's worth while investing in a post card, that way you'll know exactly where the machine fails to post. It's a PCIe card but you can use an m.2 to PCI adapter and plug it into the wifi slot

@armirol

2 ай бұрын

I usually add a tiny pc speaker to hear any POST codes bips... it helps diagnose at what stage it fails.

@R4MP4G3RXD

2 ай бұрын

@@armirol not all motherboards have a speaker pin unfortunately, this is where a post card comes in handy

@armirol

2 ай бұрын

@@R4MP4G3RXD I haven't experienced it yet, I don't even own one of those disgnostic module.... i always try to connect that tiny speaker and it worked for me so far.

I have two mini-PCs and boy, there's a reason that they put a BIOS Reset button on them. With the unlocked do-whatever-you-want BIOS, you can do stuff that you shouldn't have access to, like enabling PEG graphics... (I don't think this applies to your case unless the BIOS really gets stuck without battery power)

@idan678

2 ай бұрын

what does peg graphics means and what can it cause?

@TommyCrosby

2 ай бұрын

@idan678 PCI Express Graphics (i.e., discrete / external GPU) I should have written "Set Graphics Priority to PEG" because it's not something you enable but a selection menu (also, exact wording change depending board manufacturer). It allows the user to select what graphic card should be used and have options like Auto, IDG (Internal Display Graphics), and PEG. This setting when set to PEG will ignore the internal graphics at boot.

@vx-iidu

2 ай бұрын

​@@TommyCrosbyYou can actually attach PCI Express graphics cards to these mini PCs through an adapter for the M.2 slot. I have such a setup on my desk at the moment. I wonder whether that setting in the BIOs would actually do anything if you had such a setup

If you have a thermal camera, check the board with the power on to see if anything is overheating. If you don't have a thermal camera you can put alcohol on the board and see if it evaporates quickly over a specific chip to see if there's a short. Northridge fix has videos on this method.

@CompHwTipsAndTutorials

2 ай бұрын

I was thinking about doing that isopropyl method (can't afford a thermal cam... wish they were cheaper!), but the resistances around the board and even on the dead rail all seemed like they were right, so I don't think there were any shorts in this case

I've noticed some of the Beelink machines (and other machines from the no-name Chinese vendors) have a thing, where they don't display for like 2-3 minutes on the first boot after you swap out their memory. Maybe it's a memory training issue? On mine, it made me think the mini PC was dead until I walked away from it to make some coffee and I found it at the BIOS splash screen when I got back.

@45KevinR

2 ай бұрын

On servethehome forums it's pretty clear that the common oems of CWWK & BKHD have bioses that only configure the ram by doing training. And with big dimms that takes a while. Changing ram seems to often need a bios reset (what we used to call a "cmos clear") inorder to force the training to rerun. I'm not clear if they work that way to cope with cheap in-China ram, or if there's a big bucks licence needed to be allowed to read the embedded configuration from the dimm. People have also had issues where their specific device hated certain hdmi cables or monitors. And more oddly that could fix itself if you ever got it to boot once using say display port, or got an OS to boot. So there may be interactions in the BIOS/EUFI/OS pathway. Thinking about this kind of thing, we had an Asus Zenbook laptop die last year - all we did was open it up (far too hard a challenge), swap the sodimm from 16 to 32, and the laptop never booted again! So modern tech is getting super fragile again.

I think the Beelink issue could be as simple as a corrupted Bios, remember that the bios itself is responsible for the whole startup procedure and if this gets broken the motherboard gets bricked too. either a flashback function or a chip programmer to re-flash the bios again would probably fix this computer. since the bios is powered even with the system turned off it could cause issues if you yoink the ram while in hibernation or the like and the system expects a different chip to be in place it may corrupt the data in bios. make sure the bios is actually completely reset or restored before you quit this one

@CompHwTipsAndTutorials

2 ай бұрын

Makes sense to me, I honestly just never thought of the BIOS even though it makes sense now that people are pointing it out. Won't be giving up on it until I have an opportunity to try reflashing it!

@KenSvensson

Ай бұрын

+1 on this. It's easy to reflash the bios and simple to rule this out.

For the BeeLink - Recently replaced SODIMM RAM on a laptop (HP). Power is never really “disconnected” and I had no issues. I know there are “power off” options in some laptop BIOS to, as best as possible, remove power but didn’t see one. From other comments from people with boards from the same company, could it be a flaw that they treated power as a desktop instead of a laptop, so that, with plugged in power, that left power on that fried the channel? I definitely think you’re on the right track. Also seems others had issues replacing boards other than RAM, so could just be a manufacturer issue too. Thanks for the great troubleshooting process!

Put a terminal based linux on an ssd and try to access the system remotely to check if the igpu took down the whole cpu or just the igpu part.

@CompHwTipsAndTutorials

2 ай бұрын

Now THAT is a great idea! Imaging a drive with some headless Linux install and trying to SSH into it or something is actually genius, thanks for this!

@ricardog2165

Ай бұрын

@@CompHwTipsAndTutorials Is the drive activity LED turning on at any point?

@WoNCrawler

Ай бұрын

@@CompHwTipsAndTutorials did it work?

I have chatreey T8 Pro and bumped into the same situation. Sometimes it boots from the first powering on, but never come back after few hundres of power cycles, works again, and never turned off from now. I didn't know what was the actual issue and now I can see many people in here pointing out the corrupted bios, I now found the manufactuter provides bios update and tried... my problem actually solved. Thanks for the video. I was sick of it.

Very thorough explanation and very simple to understand. Really admirable skills you've got there. I tried something similar with an old Lenovo ThinkPad Motherboard but Alas! never got it working. Keep up the good work!

@CompHwTipsAndTutorials

2 ай бұрын

Thank you for the kind words!

This video is 😂 funny, in a good way. When the resistor flew away and when he ripped the pads for the resistor. I hope you keep making videos and learning computer repairs. Also they sell very cheap memory tester to test open and shorts from memory to CPU

I bought one of these N100 minipcs for my parents and it came dead, very similar issue to the Beelink. I did not manage to fix it either: tried similar Voltage(and Amps - not that it matters) charger, probed some resistors and no issue there, tried HDMI to DVI and HDMI to VGA adapters, also removed the battery to reset BIOS, did packet capture with my firewall and it’s basically dead(no action, just NIC network discovery that happens anyway), tried with and without RAM and/or SSD. I was really hoping you are going to hit the nail on the head.

@CompHwTipsAndTutorials

2 ай бұрын

I'm sorry to hear that you received a dud PC. Did you try reaching out to support at all? I also really wish I had found a way to fix it, would have been useful info for someone like you, I'm sure! It may be possible that the CPU didn't properly solder to the board at the factory in your case, considering it was brand new and exhibiting these same issues I found and deemed to be CPU related.

@aliancemd

2 ай бұрын

​@@CompHwTipsAndTutorials I bought this one from AliExpress and they did refund me. On a side note though, I gave it another try with the multimeter today(continuity tests) and found 2 capacitors and 1 resistor in front of them not closing the circuit, right on the other side of the RAM connections with the board. I think I found the problematic resistor but it's so tiny that I definitely can't repair that, can't even put it on a soldering plate because it's filled with components.

@CompHwTipsAndTutorials

2 ай бұрын

Glad to hear you at least got your money back, that would have been a real bummer if you hadn't. That's cool that you picked it up and did some more troubleshooting! I totally feel you on how those resistors are too tiny to repair. I guarantee I would not have been able to do it in my case without a microscope, which is extra cost that isn't very worthwhile if you don't use it often.

Given the lack of video support, it may have been wiser to have first attempted a headless Linux boot from a USB stick with serial USB terminal before going so deep.

A lot of point of sales have gone to these compact units, but with PS/2 compatibility for legacy systems with sVGA, but often there's HDMLI ready to go. Our main issue is configuring it to use whatever the site's needs are and shut off the rest until the next service upgrade.

Wow! Superb job! I did not understand much of what you said towards the end of the video, but it was fun to watch either way!

@CompHwTipsAndTutorials

2 ай бұрын

Glad you enjoyed it!

@dezhocob

2 ай бұрын

@@CompHwTipsAndTutorials Question, I have a laptop that does not work and I want to rule out the power brick. I have no idea about electrical engineering. How did you probe that power cable's voltage, I know you used a multimeter but what settings?

@CompHwTipsAndTutorials

2 ай бұрын

For sure! I set my multimeter to DC Volts, and my multimeter is an auto ranging one. Since most laptops don't use a higher than 19V supply, if you don't have an auto ranging multimeter, I'd select the "20" option within the DC Volts setting. I then put the red (+) probe in the hole in the barrel jack and measured the negative pole by touching the black probe to the outer bit of metal. If your barrel jack is of the less common type that has a pin in the center of it, touch the red probe to that pin and the black probe should still go on the outer sleeve. Hope that helps!

@dezhocob

2 ай бұрын

@@CompHwTipsAndTutorials It does! Thank you!

Yeah, do NOT screw around with anything on these mini PCs with the power connected. I fried one of my two Intel NUCs by doing basically the same thing as the guy with the Beelink did, try to change memory with the power connected. Luckily the one I fried was a cheap one. Exact same symptoms as the beelink.

Great video. And I agree with your diagnosis on the no post n100

If the 4th phase was not controlled or broken, the fans would not spin. The 4th phase can also be the turbo booster, which is normally turned off. The 1.8V phase is probably the PCH, not the IGPU, although the GPU is supposed to be in the PCH of the N100. Test all your phases in ohms mode. If they are not close to 0 ohms, say 20 ohms, they are fine. If they are lower, you can confirm that the CPU is dead by applying voltage to the phase (0.5 V, 500 mA) with some alcohol on the DIE. If the whole area gets hot, the CPU is fine. If one corner lights up, the DIE is broken. My guess is that the N100 is fine. Instead, I suggest you focus more on the 3.3V PCH rail, as this is likely to be the problem. Test pin 8 of the bios SPI IC, which should bring 3.3 V. In most cases in these small PCs, the ram SPD SPI IC is in parallel to the bios SPI IC, both powered by the 3.3 V rail of the PCH. My guess is that the ram swap triggered voltager on the SPI lines of the bios IC (through the rams SPD / SPI). Try dumping the bios and open it in the UEFI tool and look for any errors. Also reflash the bios with a clean (ME) dump. Since the pc turns on shorly and the fans spin, my guess is that it 's somehow bios / SPI related.

A good tektronics oscilloscope with a good 1x probe for interpreting signal quality and signal over time would tell you a lot more about what is and isn’t happening. Keep challenging yourself. Looking at things you’re not familiar with is the best way to learn. Don’t be scared, it’s already broken. Well done dude.

Im amazed to see u already have sponsors at that small of a channel size!

Something many troubleshooters seem to forget to try is boot with no memory. The system will of cause detect it and will beep (if there is a sounder) or flash a code on the system led's. If it doesn't do that its stuck before memory and that is CPU or before bios test starting AKA power problems or firmware.

Very interesting ! I'm having the same issue with a Fitlet2 Intel mini pc board. After changing something in the bios the screen is dark. I think a bios problem. So keep trying to fix it !

I love those Beelink PC's. I have four of them. They are all AMD CPU based. The oldest one will sometimes "forget" which SSD the OS is installed on and you have to boot to the BIOS and select the correct drive. Other than that one issue they work great.

"Finding schematics for __THIS__ computer was never going to happen" - i like the approach :), sad but __TRUE__ ;) Thanks for pointing that "CMOS" reference - cmos technology was a great break in the 70s but nobody now remembers how great it is, i dont even remember when have it started.

You can sort of test the mem CTRL in cpu, put + probe on ground and with negative probe go over ram datalines But its like 98% that cpu is done

@CompHwTipsAndTutorials

2 ай бұрын

I might have to give that a shot, even if it's very likely it's the CPU

You did your best brother and accepted defeat gracefully. Well done.

Fascinating! I am most certainly nowhere near as smart as you, but I had a thought about the remaining dead one! I have a similar issue with a NUC of mine, essentially dead beyond the power light and fan. but I noticed that trying to boot it with the RAM removed, the power buttons light had changed, AND with speakers plugged in to its headphone jack I DID get a beep! so there is some kind of a status check still operating! I'm planning on getting a thermal camera so I can see if anything is abnormally hot when attempting to boot, RAM installed or not. Could be helpful! Great video pal, keep up the good work! 😁🧡

@CompHwTipsAndTutorials

Ай бұрын

Thanks for the kind words man! That's really interesting that you got beeps out of the headphone jack, I'd never thought of that myself! I'll definitely be giving that a try when I revisit it, thanks!

You need to invest in a hot air rework station for dealing with surface mount devices. Also look for tin whiskers when looking at the board when looking at it through the microscope.

did you try unplugging it and plugging it back in? ( sorry had to lol ) great video.

My similar Beelink refused starting due to the glue under BIOS battery became conductive and shorted IO signals. After cleaning it works fine again.

POST order of checks is pretty different on all the hardware out there. I think your general thoughts are right about the order, but I've seen modern boards with different support for special hardware or just different OSes, that would change the POST order behaviour. Allways guessed there was a general order tree, but in special scenarios it would traverse other order than the actual tree order. And also: Very nice video!

@CompHwTipsAndTutorials

2 ай бұрын

Thanks for the compliment! And that's a good point about it possibly being a bit of a special board that doesn't go in a more common POST order. I wonder how one would go about figuring out the POST order a specific board uses

Use an m.2 (x4) to pci-e adapter and an external video card.

You are probably right about the BeeLink. If you wanted to test further, you could see if you could get an adapter to hook up a PCIe video card to the M.2 slot. I doubt it would yield any results other than more confirmation.

I bought a Beelink Mini PC. All was well, until it refused to work with a brand new SSD mounted in a USB enclosure. At first I suspected the SSD, but my Beelink's USB ports are very flaky, and connected drives malfunction. Beelink were no help at all! Amazon gave me a full refund, and let me keep the Beelink. I then bought a Minisforum, which unlike the Beelink, works perfectly with all my USB drives! I like Mini PCs due to their tiny form factor, and their highly efficient energy usage, compared to my old home built desktop! Also, this allowed me to upgrade to Windows 11, love it or hate it, for very little money!

@jimw7916

2 ай бұрын

beelink are turning out to be unreliable in the long term.

@armirol

2 ай бұрын

i've got many tiny Beelink PCs and never experienced bad one... those are pretty good. I guess it's bad luck

in smaller systems like laptops and mini pc's with igpu's the ram is sometimes shared between the cpu and igpu so switching it while plugged in killing the igpu is actually very likely if it is one of these systems (probably since a lot do it this way)

@CompHwTipsAndTutorials

2 ай бұрын

Kind of what I was thinking with that memory/iGPU relationship there

Have you disconnect the cmos battery and short out the positive and negative on the mainboard where the battery is plugin.

@CompHwTipsAndTutorials

2 ай бұрын

I did disconnect the CMOS battery, but I hadn't specifically tried shorting the main power terminals on the mainboard. May be worth a shot!

I guess the only thing I could think off that can be done for the n100 is to power on the PC without ram installed and check for heat/power draw differences and hope it's a case of multiple ddr5 modules being bad/damaged by the powered scenario.

your theory makes sense about the blink pc (one you troubleshooted first ddr5 ram that had

Great video!

If the Blink system supports a direct flash BIOS image it might be worth while to see if maybe it got corrupted and just needs to be flashed with a working image. It's logical that something like that would happen if the BIOS were active because their normally connected to the memory in that the BIOS image get's written to memory when the system boots. It does this because the RAM is generally faster than the BIOS chip. At least that was the case for older systems. Point of the matter is this. Attempting to flash a good image to it might be worth a shot. Like you said, "it's already broken."

Getting all the voltages on the various rails is a good way to diagnose some possible problems. Don't forget to also find the on board fuses and 0 ohm resistors between the voltage rails and the actual power using chips. You have found a few, but you did not explicitly say in the video you checked all. You may have done so off camera?

I was writing something as you were explaining your theory. By the end, i deleted it. The board is cooked. You could try an external GPU unit to see if you get a bios but thats not a certainty

What you could try is an external gpu by using a m.2 to pcie adapter to see if it does work and if the igpu is the problem.

Its never ever the CPU. Until it is. Side note, I love those little Beelink PCs. I have two! They work great for home office type environments.

If you suspect that the iGPU are broken, maybe you can buy adapter for M.2 to Oculink adapter, and then connect external GPU using that oculing with external PSU.

Introduce a signal to the igpu power driver to jump start it. If it starts there’s something in the power circuit If it doesn’t the igpu is dead 🤷🏻‍♀️

@CompHwTipsAndTutorials

2 ай бұрын

I could definitely give that a shot! I just don't know what voltage would be good to inject there, any ideas?

@CB_agotchi

2 ай бұрын

@@CompHwTipsAndTutorialsis the driver the same on the vcore drivers? I’d mimic that input if they’re the same.

@CompHwTipsAndTutorials

2 ай бұрын

It's the identical driver circuitry, but it's connected to a different rail output on the controller chip, so I think it would likely be a different voltage. 0.85V wouldn't be a bad place to start though, as it's almost certain to not fry something

That could be a boost phase, ie, off until it's needed. Since most voltages are ok, I think I would go for bios.

@CompHwTipsAndTutorials

2 ай бұрын

A couple people have pointed out the BIOS, definitely going to give that a shot in a future vid.

I understand the reason for going to all that trouble is for the purpose of doing a video about how to repair one of these mini pc's, but you made the most important point at the end of the video: they are so cheap that it's worth chucking a dead one in the bin and buying a new one to replace it. I have had good luck with MinisForum, and I have a Xulu hopefully coming sometime this year from a Kickstarter project. Fingers crossed on that one. Beelink, though, seems like its reliability is not all that great. Great video, and you showed why these mini-PCs are a bit of crap shoot.

Reguarding the latter part of the video - is there not any way to attach a buzer to the motherboard for beep codes? my Desktop pc definitely boots CPU, RAM, GPU and has bios lights to show this stage step through of the post process

when you plug in a RJ45 ethernet cable &/or a optical mouse does the ethernet port blink & the mouse optical led light up? I seen this a lot when people would plug a USB device into a ethernet port. The i/o on the m/b is dead, no fixing it, the time needed ..it would be cheaper just replacing it.

@CompHwTipsAndTutorials

26 күн бұрын

Definitely going to try plugging in ethernet when I revisit this!

That was insane in the membrane 😮

You're almost their , Check the IC that controls the HDMI if power is their then yes you have a dead super IO and will need to be replaced using hot air rework, but if your not confident in micro soldering I would not attempt. But your close ,Good job troubleshooting

Nice video. Hope there's a follow up soon.

the serial port, jtag, spi bus, and post cards are your friend. try putting the beelink in a reflow oven, could be stuck transistors or a dry solder joint.

I think you can extract video signal from that wifi slot with external gpu wifi to pcie adapter

14:04 btw you do not need to worry. you can just leave these dies "empty" when testing. just make sure to put a finger on it occasionally to feel if it's overheating or not. these modern cpu's are so safe you do not need a heatsink most the time lol. theres a video of someone pointed a thermal imager onto a ryzen CPU's bare die with some program stressing each core.

@CompHwTipsAndTutorials

2 ай бұрын

Ahh okay, good to know it's less of a massive deal than I imagined. I was aware that the CPUs are pretty good at protecting themselves from overheating by shutting down/throttling, I just wasn't sure whether that would happen so fast with a bare die that it could interfere with POST

Maybe there are bad cpu pads 😮 but cant know till you know great insight on broken things to bad many things can break them and not enough safety 😅

Most modern motherboards have a lpc header which can be used with appropriate post debug card to see what is really going on

The Beelink one can be the same problem from Xulu Mini PC, do a checkup arround the Power Circuit and this same resistor from the Power Circuit is the frist thing to do on this board. Edit: I noticed two corroded SMD Capacitors behind the memory slots, this may be the problem source.

Good stuff.

They must have a way of testing those boards during manufacture. To that end I saw several test pads ready to take spring probes in a jig. What if you try any of those pads with a scope. Is there any lilfe in them?

Well one thing that is allso helpful is to setup a postcode monitor. There you get at least an indication where the cpu is hanging.

See if there are any TVS diodes near the RAM connector that look compromised. It's possible that hot-plugging the RAM with the PC on was enough to blow one of them short. Conveniently enough most integrated graphics solutions use the system RAM as their VRAM. It's possible that a short (or partial short since it's not drawing an insane amount of current) may be causing a fault in this power rail shared between the iGPU and system RAM which now won't turn on as a protection mechanism. You can probably check this pretty easily first by measuring the resistance of this power rail to ground. Anything less than a few kOhm would be pretty suspicious. A bit of an out there theory but something worth checking if all else fails.

For some guy like tihs Carey that works with computer over the years, not disconnecting the power from the mini pcs... is a crime. Obviously, something will break no matter which platform. I once installed a RAM module when the power was still plugged and ended up burning the slot. ALWAYS remove power/battery when replacing RAM modues or other parts.

I have a Beelink N100.....you can't upgrade the RAM. 16 gigs of Crucial DDR4 (mine is DDR4) are all you get. The Amazon sales pitch says so. Not sure why anyone would mess with it. Ain't broke, don't fix.

Bad RAM might stop you from getting a post screen, but zero RAM shouldn't, should have tried booting with no RAM. And with it plugged in & plugged into the network, check it you saw it on your router. To me only 3 minutes in I'd guess the i/o was blown, meaning half the m/b was dead. But seeing if the Ethernet port was blinking would tell me it most likely is still good.

@CompHwTipsAndTutorials

26 күн бұрын

I've never had a system POST without any RAM, and I don't think it would have any chance of working in this case, because of the fact that the iGPU in this system requires system RAM to work

Is there oxidization or metal eaten away on the RAM connector pins? RAM unplugging and replugging while the system is on could make some pretty little sparks. Deoxit and if that doesn't work, soldering in a new RAM slot might be an interesting thing to try. Also, something to consider, if there were pretty sparks created, then maybe it could be physical slot damage due to human jumping.

@CompHwTipsAndTutorials

2 ай бұрын

Good thoughts, thanks for sharing them!

Something you could try is using the m.2 nvme slot on the motherboard and connecting an external gpu to it using adapters. I've seen dawid does tech stuff and bringus studios use that slot to connect an external gpu, so if the integrated graphics is toast maybe this would help.

@CompHwTipsAndTutorials

2 ай бұрын

I might give that a shot in the future! Also glad to hear that we both enjoy some of the same KZreadrs haha

@OneLife69-

2 ай бұрын

@CompHwTipsAndTutorials one thing to consider could be whether or not the bios is setup to accept external gpus. If its not you could de solder the bios chip, plug it into a debug/ flash board and then flash on an edited bios that does enable external gpus.

sometimes, the gravity.test and shotgun tribulation makes your day a little bit better.

I wonder if that system has a speaker if you pull the ram and it beeps an error code its a quick way to validate CPU and system board from a basic level

your skills are neat, and somehow these two Mini-PCs would be great as a Server for Media, Files, etc.

On the Zulu, that resistor is likely acting as a fuse. Most times they are very small values. Less than 1 ohm, or maybe even zero. Shorting with solder is fine for test, but putting in a 0 - 1 ohm link is preferred.

@CompHwTipsAndTutorials

Ай бұрын

I might have to see if I can get a replacement resistor, just so that the repair is a little more clean/professional.

You could try connecting an external GPU through the M.2 connector with an adapter and see what that does on the Intel mini PC.

I have a blackview MP80 mini PC the problem is that Everytime I use the Internet my screen will go on and off to a blank screen is this a problem with the Mini PC or is it a problem? I am using this on a 4K TV could that be the problem?

I have worked on computers most of my life, and I have used a diag board in the past few years successfully. I was wondering though, does that board have any pads or indicated junctions for a post speaker?

@CompHwTipsAndTutorials

Ай бұрын

I didn't search for any, but there is a chance it could have those. I'll keep that in mind when I'm revisiting it!

Integrated graphics uses main system RAM. There is a direct link between the iGPU and the SODIMM

Some integrated graphics use ram as of vram so thats probably how it broke

have u tried tyepce c video output..it may show is that cpu is working but not i gpu

Could you bypass and provide power directly?

@CompHwTipsAndTutorials

2 ай бұрын

Possibly, I may give that a shot in the future when I revisit it!

kudos for getting a through hole resister to solder to smd

@CompHwTipsAndTutorials

Ай бұрын

Thanks, it was ugly but it did the job for testing purposes haha

Tip to try, does the light or fan reacts different when the RAM isnt seated? Like longer or shorter maybe.. You didnt own DDR5 but you also never checked if that could be it, take out the ram, see if the PC reacts different, theres your possible answer, another part to this answer, order the cheapest compatible ram stick for this device (check online if there's a CVL for this board) and write that $30 as repaircosts if it works or doesnt

@frommatorav1

2 ай бұрын

He definitely did try booting with and without the SODIMM stick installed.

what "power supply" you used for testing?

@CompHwTipsAndTutorials

Ай бұрын

I used an adjustable, linear lab bench power supply

You should try attaching a small gpu through the m.2 nvme slot

While putting the RAM in while the power was on it is possible a circuit got more power it than was designed for and the chip holding the CMOS or BIOS got zeroed out which means the computer has forgotten how to turn on (POST). Install a new CMOS chip or use the box for parts.

Since I am mainly a software guru, I definitely can't help with the hardware part of things. I will give some insight on the software side of things though. Mini PC's are annoying to fix because the integrated bios chips are poorly designed and a hassle to diagnose. Although, I have gotten myself many times into a situation where digital video output, like HDMI or DP wouldn't work until the OS boot phase, after the communication protocol between the GPU and display has been set. If I were to restart the computer, the display would work just fine, outputting the post message and everything, until a complete power down happened. Then, I would have to repeat the blind process of selecting the boot drive from the boot menu. I believe this could be the problem in your case, so try plugging in a keyboard first. It is possible that an "input device missing", or "system configuration change" (since the RAM was changed) prompt could stop the boot process and therefore not completing the display output handshake. Also, have a bootable drive connected to the computer and see if there are any signs of life. These solutions helped me multiple times, especially on crummy intel atom devices.

@CompHwTipsAndTutorials

2 ай бұрын

Thanks for that insight, I'll likely give a few of those suggestions a go when I revisit this PC!

I have a question that is a bit off topic. The mat that you are working on, the gray mat with a grid pattern and the different sized circles on it. Do you have a link for it? I'd like to know more about it. I'm just starting to delve into this "kind of stuff" myself, and I am still getting my work area set up. That mat looks like it would be a nice area to do my work on. Thank you and greetings from Alaska.

@CompHwTipsAndTutorials

2 ай бұрын

Absolutely! Here's the Amazon link to the mat that I'm using: www.amazon.com/dp/B0BJKSX6J2/ref=twister_B09MMXCJNQ

@RANDOMNATION907

2 ай бұрын

@@CompHwTipsAndTutorials . . Thank you!

15:51 ... "In short" ⚡🤣

@CompHwTipsAndTutorials

2 ай бұрын

Haha I didn't even catch that until you pointed it out!

the beelink ones are dropping like flies apparently

@CompHwTipsAndTutorials

2 ай бұрын

You could even say that they're dropping... like bees! Sorry, I had to, haha!

Stupid question... Is there any motherboard speaker output jumper on that motherboard? If there is, and you can hook a small speaker to it, it may give you some diagnostic beeps.

@CompHwTipsAndTutorials

26 күн бұрын

I didn't check for that, I'll certainly be doing that when I come back to the beelink!

Sorin from Electronics repair school has discord that has many many many bios images and also a great repair community for laptops. They may be able to help you as well.

on those mini pc sometimes the power out put is so high and when they changed the ram they broke a power over ride fuse. so its simple find the power over ride fuse on that motherboard and it should work just fine all u need to do is bridge the cap

@CompHwTipsAndTutorials

2 ай бұрын

Interesting point, all I know for sure was that the RAM power phase was outputting its 1.1V, but I didn't actually check whether or not that made it all the way to the DIMM slot pins, I'll have to check that when I revisit the board!

@amnjimmy77

2 ай бұрын

@@CompHwTipsAndTutorials they have a power over ride chip u need to remove...