High technology and nice products! I'm looking forward to it! from Japan

Thanks this was really helpful I might try one!

Thank you so much for this video. I made 2 rings and they came out great. Thanks again.

@CraftSuppliesUSA

Жыл бұрын

That is great to hear! Have fun turning!

Complimenti ottimo tutorial

Super cool and good 🥇🥇🥇👍🏼👍🏼👍🏼

You just inspired me to do 👍😎

@CraftSuppliesUSA

Жыл бұрын

Glad you liked it!

Nice video

Hi Mike, fill the Inlay in a empty (new/clean) long nose CA Glue Bottle and you can drop corn by corn of inlay. best regards from Germany Gerhard (former woodturning supply dealer, now retired) ,-))

@CraftSuppliesUSA

4 жыл бұрын

Thanks for the tip!

nice working，great。l'm thinking how to make the ring in the movie of the lord of the rings.😅

If only I had a lathe.

تحية طيبة لك. عمل جيد

What rpm do you use in different stages?

A lot of times the glue comes out of the ring when I use the carbide tool. What can I do to stop this from happening? Thank you

Can you use a blank for this ring? I think u can

Could you turn rings with the Apprentice 812 VS Mini Lathe?

What is the buffing compound being used on the buffing wheel at the end? Can I buy it on your website? Thanks.

when i use the activator the CA glue turns white. How can I keep from doing this?

Anyone recommend a suitable CA glue and activator in the UK? Many thanks

there is an easier way! I will be trying soon!

Hello sir, could you tell me where I can buy the earrings, for the rings ... excellent your work, congratulations

@CraftSuppliesUSA

3 жыл бұрын

Here is a link to the ring cores: www.woodturnerscatalog.com/p/58/7264/artisan-Inlay-Comfort-Ring-Core

How much would you sell rings like these

will the carbide tool scratch the ring core

hey man, do you sell the stuff for the craft of the rings? can you shipp to brasil? great job!

Isn't cyanoacrylate not recommended for silver, or metals in generl.

Could an inlay ring blank be filled with sawdust from a special piece of wood to the recipient?

@cliffburlew9209

9 ай бұрын

Yes I do that a lot

Tell me about ca glue

Mike, my first inlay ring resulted in cloudy white CA on parts of the inlay. How do I avoid this?

@The_Conqueeftador

2 жыл бұрын

Same. The activator can cause cloudyness. I can never get any CA finish as beautiful as these youtube videos.

@jrobins3547

2 жыл бұрын

Yeah it did the same to me.

What they don't tell you is that the activator only dries the top surface of the glue, I learned this the hard way so make sure to wait at least 20 minutes before starting to turn your ring to let the glue fully set all the way through

@deskmat9874

10 ай бұрын

I think its better to put in activator first then use thin glue when the inlay is inside

I plan on making my first inlay ring with UV resin. Do you have any tips? Please message me. Thanks very nice video!!

@carolstewart1704

2 жыл бұрын

This is the info I am looking for as well.

Does the ring scratch with the carbide tool if so does it polish out

@CraftSuppliesUSA

9 ай бұрын

Carbide can scratch the core, but can be easily polished out.

can I request a ring?

will the white from the spray turn out? on the lathe.

@CraftSuppliesUSA

9 ай бұрын

Most of the time it does. If it doesn't, I recommend using an Exacto knife to cut out the white areas.

Like to know where you purchase the ring check looked on your channel Supply Channel USA doesn't have one.

@CraftSuppliesUSA

Жыл бұрын

www.woodturnerscatalog.com/Sales/52/Ring-Turning

what happens if you hit the core when cutting down the inlay ofhow to miss the core????? Thank you Ed

@CraftSuppliesUSA

Жыл бұрын

If you hit the core it will scratch the core. However you can always polish that surface if needed. You can use a narrow parting tool to cut the material down without hitting the sides of the core.

Where can I get the stuff you used to make ring

@CraftSuppliesUSA

2 жыл бұрын

www.woodturnerscatalog.com/Sales/52/Ring-Turning

I love your products, but I think I have run into a problem. I followed the instructions as on the video, from the sharpie to the products; I ordered them all from Craft Supplies USA. I made rings for my wife and I and they looked pretty good for the first time. Now, the first thing is something that I thought about from the beginning, what is there for the CA to grab ahold of? Answer is nothing. This is where I think part of the problem comes from. So here is what happened. I was typing earlier today and happen to look at my finger. My ring was missing a huge chunk out of it. I wear a size 10 and the channel is relatively deep and wide. When I touched the rest of the inlay it began to come off the ring as if nothing. Even the black coating from the shapie was gone. Most of the ring is smooth as if nothing was ever on it, there was no adhesion to the ring itself. And my next question is, isn't CA relatively brittle to begin with? I bought a few sizes to try, and see how they sold. However, without a reliable bond and ensuring that the ring isn't going to break with a slight bump, I cannot sell these at all. Your suggestion on how to fix this is greatly appreciated.

@leftmono1016

4 жыл бұрын

Raul Fuster - I've only just started inlay rings and have had the opposite problem to you - I used a cheap turquoise inlay, didn't care for it, and it was incredible tough to break out. A lot of videos show the blank being roughed up with a needle file in order to give the CA something to grab on to. That also helps remove any contamination on the surface of the blank.

@trainwon5699

4 жыл бұрын

Raul Fuster I would rough up the surface with sand paper then clean it with denatured alcohol then use the marker. Hope this helps

Very stupid question, buy is the lathe a wood lathe or metal lathe?

@CraftSuppliesUSA

2 жыл бұрын

Not a stupid question at all! It is a wood lathe - www.woodturnerscatalog.com/p/216/7024/powermatic-3520C-Lathe

How come the glue becomes cloudy?

@CraftSuppliesUSA

2 жыл бұрын

Typically the clouding comes when applying too much activator. I find it helps to spray the activator from further away (8-10 inches from the piece) and to use an aerosol can instead of a pump sprayer . Activating the glue too fast creates too much heat which leads to the clouding effect. Hope this helps! If you want more specific help, call our tech support at 1-800-551-8876

ألقَرٍنٌبُعٍ . مَعُي و عًنْدي قال الله تعالى(وَقُلْ جَاءَ الْحَقُّ وَزَهَقَ الْبَاطِلُ ۚ إِنَّ الْبَاطِلَ كَانَ زَهُوقًا).الْآيَة جَاءَ.أعُمْلُوَا أرَأء.وألحَمْدِلله وَألشُكْر لِلَّه.

can i have one of this i give to my wife

I got half way through before I thought to myself... why would someone who's buying a ring blank have a lathe and carbide tooling... surely if they had a lathe it would be cheaper to just make your own ring blanks

@ParkerDesigns05

5 ай бұрын

It may be cheaper but you have to think about time consumption. Spending a couple of hours just to make an identical copy of something you can buy for £8 is a waste of time, especially when you’re selling your rings!

@mikeyduke10

5 ай бұрын

@@ParkerDesigns05 takes a lot less craftsman ship though

@ParkerDesigns05

5 ай бұрын

@@mikeyduke10 as someone who makes rings themselves I can see what you’re getting at and I agree, however from a business point of view there’s really no point. It’s not like you’re trying to prove that you’re amazing at your craft, most people (especially the customers) only care about the finished product, not about if you’ve made the ring blank or not

Jesus loves you and died on a cross and rose three days later taking our place and paying our debt (for the wages of sin is death) so you can have eternal life and be forgiven of sin if you repent and pick up your cross and follow him daily

@hirenrajput4062

2 жыл бұрын

Kalor

@richedgar3322

Жыл бұрын

keep your jesusfreak stuff to yourself

Can you mount a star sapphire on a ring like that?

@CraftSuppliesUSA

6 ай бұрын

The channel may not be deep enough to fit a gem.