Turbo Hose Inner Seal Replacement - Peugeot 308 1.6 HDi
Removing and replacing the turbo hose inner seal in a Peugeot 308 1.6 HDi. The part number on the old seal was 993563. Thanks for watching, please comment, like and subscribe !.
~~~~ Part Links ~~~~
As an Amazon Associate I earn from qualifying purchases.
🚗 Turbo Pipe Sleeve ~ amzn.to/3OuZvKo
Disclaimer: Screwsnutsandbolts is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to www.amazon.co.uk
All of my uploaded material is protected under copyright law. None of my videos may be re-uploaded, reproduced or transmitted, in part or in full, in any form or by any means, without the written permission of the copyright holder.
© / screwsnutsandbolts 2022
Read important information below:
Disclaimer
Under no circumstances will Screwsnutsandbolts be responsible or liable in any way for any content, including but not limited to, any errors or omissions in the content, or for any loss or damage of any kind incurred as a result of any content communicated in this video, whether by Screwsnutsandbolts or a third party. In no event shall Screwsnutsandbolts be liable for any special, indirect or consequential damages or any damages whatsoever resulting from loss of use, data or profits arising out of or in connection with the availability, use or performance of any information communicated in this video. Due to factors beyond the control of Screwsnutsandbolts, it cannot guarantee against improper use or unauthorized modifications of this information. Screwsnutsandbolts assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. Screwsnutsandbolts recommends safe practices when performing any do it yourself repairs and or with tools seen or implied in this video. Due to factors beyond the control of Screwsnutsandbolts, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Screwsnutsandbolts.
Пікірлер: 56
Here's how to use the Stop & Go Tyre Mushroom Plug Kit: kzread.info/dash/bejne/d2SMy49-h9DdqNY.html
Good vid
@screwsnutsandbolts
5 жыл бұрын
Thanks very much !
If the pipe comes off would it cause the engine management light to come on and give a boost control fault
It's probably one of the reason's many 1.6 HDI's sound like tanks.
@at4466
5 жыл бұрын
loose distribution chain on thp motors make them sound like that
@jaggass
5 жыл бұрын
I haven't heard many rattle but plenty that sound like that they don't have an air filter. Later Peugeot's 1.6 HDI's are much quieter.
@at4466
5 жыл бұрын
@@jaggass The T7 HDIs have shitty air filter attachments and the air filter box does rattle when they're broken. But it's a different, thumping kinda rattle. Here's what the THP loose chain sounds like. kzread.info/dash/bejne/p2eJmJl8Zay4crQ.html
Hello! Does 1.6 hdi from Peugeot 308 2015 T9 have this sealing?)) And for the same engine maybe you know cure for the rattling air filter box?)
@screwsnutsandbolts
7 ай бұрын
I haven't worked on the newer model so I'm not too sure but if it has a turbo it probably has a similar seal. On this model, the air filter housing is pressed down onto rubber mountings and the rear of the filter housing lid has lugs at the back that should fit into slots at the back of the housing before closing the front of it. If it's similar on the newer model it may not be seated correctly of the rubber mounts, or maybe the lid isn't closed right ?
Niiiceee
@screwsnutsandbolts
Жыл бұрын
Thanks !
My new seal keeps popping off. It's driving me insane 😅
@screwsnutsandbolts
3 жыл бұрын
Make sure the pipe and seal are clean and dry and don't overtighten it.
@lourencobento6582
3 жыл бұрын
@@screwsnutsandbolts I think it was the overtightening. Thank you!
@screwsnutsandbolts
3 жыл бұрын
@@lourencobento6582 You're welcome. I did the same myself lol :)
Hi . I have a 208 1.6 hdi .. with turbo whislte loud.. .. still habe boost just makes horrable noise .. do i change turbo .. and if so is ther anythin else i can put on ????
@screwsnutsandbolts
4 жыл бұрын
You should really have a mechanic take a look at it just to be sure
@ScrewsNutsAndBolts found it at UK's EuroCarParts so glad, hope non of small bits of the old seal didn't get into the turbo yet. There alway is some leaked oil on the engine, which usually comes out middle connection point with the secure clip, no matter how many times an o-rings are being replaced, after some time it start to leak again, do you have any special way to prevent that? o rings don't seem to do the job very well.
@screwsnutsandbolts
4 жыл бұрын
I can't help you there, sorry. I just changed the seal and nothing more :)
@staxuevewot2216
4 жыл бұрын
@@screwsnutsandbolts thanks anyway
@chisty4436
4 жыл бұрын
Use a bigger o ring
please whats the benefits of cleaning the turbo and how much kilometers to know when u need to clean ??
So the turbo bearing is leaking oil, but is so often problem after some time they so they made this seal to not show oil leak to owners and burn all oil in engine or collect it in EGR? How many miles/kms you have on it?
@screwsnutsandbolts
5 жыл бұрын
There's about 130,000 kms on it
@niccots
5 жыл бұрын
@@screwsnutsandbolts Nearly the same as mine.
@NordinIdrisMunir
5 жыл бұрын
same here, 130k so far.. and the turbo bearing is leaking too... so shall i just ignore it?
@Bootlerov
5 жыл бұрын
Hey y’all! Often misconception. There is no need for premature panic. If you see oil there it DOES NOT MEAN that the turbocharger is seeping oil and dying (however it might be that as well). You have a PCV (positive crankshaft ventilation) inlet right upstream the turbo (design feature) - here is your #1 oil provider in that area starting the first mile. Those Garrets live 200-250 kkm at least unless you ‘help’ cutting their lifespan. You may always check for turbo shaft play with your fingers.
@BillOdyssey
4 жыл бұрын
I have that ratchet too! Nice vid m8 👍
what prompted you to change it, looked ok from outside?
@screwsnutsandbolts
4 жыл бұрын
I had taken it off before and I noticed it had a split in it so I already knew it needed to be replaced :)
@screwsnutsandbolts
4 жыл бұрын
@Bojan Sobota No I never noticed any different sound from the engine. I just happened to notice it while I was checking something else.
@thatbig1
4 жыл бұрын
ScrewsNutsAndBolts mines split on my outlander and they don’t do a replacement sleeve want £160 for the full pipe so I’m going to build a replacement intake pip with ally tube and Samco hoses and fit a oil catch tank on the crankcase breather
@screwsnutsandbolts
4 жыл бұрын
@@thatbig1 Sounds like a plan. Good luck with that ! :)
@garageprojects9294
2 жыл бұрын
@@thatbig1 or just order one from Amazon for £20 mate
Bonjour.spv j'ai pas ce joint sur ma voiture es ce que c'est normal ou il manque merci beaucoup
@screwsnutsandbolts
4 жыл бұрын
Is it the same model as this 2007 to 2012 Peugeot 308 1.6 HDi ?
I put a new one on and it’s sliding off? !
@screwsnutsandbolts
Жыл бұрын
You're probably tightening it too much. Make sure you wipe any oil off the pipe and new seal and only tighten it enough to grip the pipe.
Mine keeps popping off no matter how well I clean it or tighten the clip. Anybody else got this issue or know how to fix it?
@screwsnutsandbolts
2 жыл бұрын
Make sure the pipe is clean and dry and don't over-tighten it. If it's too tight it will pop off eventually
@mkoza76
2 жыл бұрын
@@screwsnutsandbolts I've cleaned out with degreaser in the past & it only lasted s day or two. I'll try tightening it up less. Thanks!
@screwsnutsandbolts
2 жыл бұрын
@@mkoza76 I had that same problem and it worked for me. Let me know how you get on
@mkoza76
2 жыл бұрын
@@screwsnutsandbolts I gave it a good clean yesterday & tightened the clip snug with only a screwdriver as opposed to socket. Took it for about a 20 mile drive & it stayed on. Maybe this has fixed it! I'll give it a couple of weeks & see :) Cheers!
@screwsnutsandbolts
2 жыл бұрын
@@mkoza76 You're welcome. Hopefully that'll stay on now 👍
Part of this seal went in the turbo and damaged it.
@staxuevewot2216
4 жыл бұрын
actually happened to you? I was afraid same thing can mess up my turbo.
@Mars2Moon
3 жыл бұрын
I had the same problem, turbo ate my entire pink seal during a hard acceleration , I'm waiting now for the new turbo core and the intercooler because is full of debris from turbo fan and pink rubber. Good job PSA
pedazo de video ❤️👍🏽👍🏽 si tenes un *308* segui en Instagram *308_official* ahi compartimos nuestros autos... les mando fuerte abrazo Saludos
@naouiharoun6654
3 жыл бұрын
Thank you