Tru-Cool 40K Install Saving The 4l60e 99-06
Автокөліктер мен көлік құралдары
In this video ill be showin how to install a trucool 40k musici credits-Track: Ascence - About You [NCS Release]
Music provided by NoCopyrightSounds.
Watch: • Ascence - About You | ...
Free Download / Stream: ncs.io/AboutYou • it's different - Shado... Track: Diamond Eyes - Stars [NCS Release]
Music provided by NoCopyrightSounds.
Watch: • Diamond Eyes - Stars |...
Free Download / Stream: ncs.io/Stars
Пікірлер: 258
The way the factory Transmission cooler system works is... The Hot fluid from the trans (front fitting on the trans) runs to the cooler first... It goes out of the cooler then runs into the top port of the Radiator... It goes out the bottom of the Radiator (where it is now cooled) and to the rear port of the Transmission. The Idea of it running through the cooler to the radiator is to "normalize" the fluid temps on both the coolant and the radiator. Lets put it this way... if you get stuck in traffic on a hot day and you just have the Front mounted cooler... you have only the airflow from you fans that have to make it through the radiator and ac condenser... your trans temps will climb. If you run it through the radiator after the cooler now you have the radiator doing the work. I have done it both ways with my Suburban 2500 towing a 6k trailer daily and having both the radiator and the cooler work the best in all situations. I would keep it running through the radiator.
@robbypro3370
Жыл бұрын
Wrong. Try again
@matthewjensen9550
Жыл бұрын
I thought it was to help get the transmission up to operating temperature quicker on a cold day
@EverythingKentucky
Жыл бұрын
The cooled down fluid comes out the top. This diagram in the video is wrong.
@robbypro3370
Жыл бұрын
@dsmitteh you are wrong. Start your engine cold, then check the Temps on the lines top and bottom. The hottest line after a minute or two is your supply line. Usually, the top, not the bottom. Manufacturerers run it to the top first because heat rises.
@EverythingKentucky
Жыл бұрын
@Robby Pro Guess every truck 99-07.5 Silverado or Sierra I've flushed, or added an auxiliary trans cooler to, someone before me hooked it up wrong. My return line has always been the top.
I bought the same cooler for my 1988 Ford F250 diesel pickup. My truck has the C6 Ford transmission, those transmissions are a lot less prone to overheat and failure than the new 4L60E, but I figure it's cheap insurance so it makes sense. You can also run it in tandem with the factory cooler in the radiator which is what I did. They can be used on a bunch of applications. And, it is just that easy to install.
@cskittle1570
8 ай бұрын
Do you have a link?
Thanks for the Video My dude!! I have already ordered mine for my 07 silverado. Looking forward to installing. Thank you fro the video!!
@JoseFlores-fm3bm
4 жыл бұрын
No problem and I’m glad I could help , if you got any questions feel free to ask 💯
Great video! Very through, I'm installing mine this weekend. This video should make it a breeze. Thanks for posting
@JoseFlores-fm3bm
4 жыл бұрын
Thank you ! I’m glad this video is helping out , if you have any questions feel free to ask
@661truckscali_style4
4 жыл бұрын
@@JoseFlores-fm3bm what does the by pass value for doesnit helps ?
Is it recommended to be installed on Chevrolet Tahoe 2017?? Any side effects after installing it? On which temperature does it keep the gear oil? Hi
this was so helpful thank you 😎💕
Cool video, petty straight to the point. Thank you
I would reccomend a trans remote filter too. I have mine located under the air filter housing
Perfect I’m getting me one this week thanks man
Good little diagrams man good video
I agree great job thanks man im going to try mine this weekend.thanks brother
@JoseFlores-fm3bm
4 жыл бұрын
Thank you I really appreciate it , It took me a while to edit but they’ll get better later down the road , and no problem if you have any questions lmk I’ll be glad to help
Thanks man very helpful 👍
The cooler is supposed to go after the radiator cooler/heater. You need to connect it in line because you want the trans fluid to warm up and flow better in really cold weather and you want to return the coolest fluid back to the trans from your new bigger cooler.
@JoseFlores-fm3bm
Жыл бұрын
I get that big it’s been going for 2 years now 40k alone and it’s been great 4l60 still holding 💪🏻
@visualzspryal8299
9 ай бұрын
@@JoseFlores-fm3bmyou bypassed the radiator? how did it do in winter
@mattblack133
5 ай бұрын
@JoseFlores-fm3bm it's still wrong.
@IDABAYAREA650I
Ай бұрын
*this can be an issue for some that live in Cold Areas like up north, but like he mentioned in the video he lives in Texas, and i live in Cali and doesn’t get that cold, so it depends on where you live that can cause that issue*
very nice. I am getting ready to do this on my 2006 sierra also
@JoseFlores-fm3bm
4 жыл бұрын
Thanks and glad to hear that ,if you have any questions about installing the tru cool just lmk I’ll be glad to help
Hey I live in Philly would you recommend bypassing the radiator or no
I seen that someone drilled out the 3/8 holes to open them up more for better flow any word?
Very good video my man 🤘🏻🤘🏻
@JoseFlores-fm3bm
3 жыл бұрын
Thank you sm!
Orale!! Mexicanada!!! I see foolios paying 50 to 80 bucks for bracket kits to mount that same cooler!
Do you hava a link to where i can get this exact tans cooler?
I dont have the trans temp on my cluster, how can i tell if the trans running hot? Im not doing a new cluster cause i literally put a new factory one in last month
Hi, is the original coolant enough only after being removed from the water cooler
since you deleted the line how do u cover the hole that open on the radiator or do u just leave it be
I'm just connecting to the two lines already out there using 3/8 brass compression couplings
I was recommended to get this cooler for my tahoe the other day and seeing how easy the install is Im going to be doing it soon
@JoseFlores-fm3bm
4 жыл бұрын
I’m glad you are I’ll make a huge difference in temp wise and keep that 4l60e out of trouble , if you have any questions feel free to ask
@TheBully010
3 жыл бұрын
@@JoseFlores-fm3bm is this considered a radiator bypass or is the transmission oil still cooled by the radiator?
@EsePlebeJosee
2 жыл бұрын
@@TheBully010 he bypassed it
@diamondboy3456
Ай бұрын
@@EsePlebeJosee so does the radiator need to be plugged up from where those lines were removed from or it doesnt effect anything not being open like that ?
Supply goes to the top, and return is the bottom. They designed it that way because heat rises. I believe there is an ANSI code for that?
Very clean and creative install. I’ll be installing mine exactly how you did it, thanks
@JoseFlores-fm3bm
4 жыл бұрын
Thank you and I’m glad to help , if you have any questions lmk
What size line did you use?
Got a link for where your ordered cooler from?
Love that dash cluster
@michaelbloom5342
2 жыл бұрын
I may be wrong, but I think that's out of a Cadillac Escalade.
A Mexican friend once told me that a crescent wrench was a Mexican socket set.
@joseflores what did you use to plug up the radiator where your lines used to connect? What is the part called/where can I get it. Thank you
@JoseFlores-fm3bm
4 жыл бұрын
I dint plug up the radiator , I just drained the remaining oil and clean around it that’s all
@chefzackkasmar6767
3 жыл бұрын
Jose Flores Great. Just installed mine. Went great. Honestly hardest part was mounting the damn thing.. hahah. I ran through radiator as well. Running cool now. Average temp of 150-160 in 80f outside temps. In the morning I’m as low as 140f in hour long drives. Also installed a 160 thermostat to keep the engine running cooler overall. Engine temp now 190. I before was runnin 200 trans and 210 engine. My 2007 Chevy Silverado 1500 z71 RWD, on 18” wheels with 33x12. I highly recommend these coolers coupled with the thermostat!
Nice video mate.
@JoseFlores-fm3bm
4 жыл бұрын
Thanks
Do you think this cooler would be good for a 4l80e ? think the temps will be around 150?
@JoseFlores-fm3bm
4 жыл бұрын
Yes , it would help it a lot since both 1500 and 2500 use the same stock transmission cooler, temp wise should also be lower between 150 and 160
I live in OKC and I have a 2012 Silverado 1500 Z71 4x4, Im kinda confused on the thermal bypass....If the transmission lines run to the radiator to get the trans up to operating temps, then I wouldnt need the bypass?
@robbypro3370
Жыл бұрын
Bypass is only needed in really cold climates
What exhaust are u running 🏃??? Am planning on putting the cooler on my 08 silver it’s been running around 210 200 any suggestions?
@JoseFlores-fm3bm
4 жыл бұрын
It’s currently strait piped , installed a tru cool on a nnbs a while back on a buddy’s truck and he’s running low 100s on cold days and 150-160 on hot weather days
Good install video
and as aces so that the clouster transmission marker works correctly
Yo can you put the link to where you got this kit ? Thanks
Thanks Jose.
ممتاز
Got a stall converter?
I also have a 03 ext cab Silverado but mine don’t have that cluster. Where can I get a gauge cluster like your?
@JoseFlores-fm3bm
4 жыл бұрын
I got mine of an Escalade , 03 and up have them
Do you have to plug the original line that went to the radiator. And how did you add the line to the transmission cooler?
@Titoo.1
2 жыл бұрын
Did you plug it?
Does it matter if you have the transmission cooler up or down
What size is the hose and hose clamps ? Or does it come with the cooler too ??
@JoseFlores-fm3bm
4 жыл бұрын
Hose clamps will come with the cooler
I live in OKC, in the winter it can get pretty cold sometimes. Do you think I could still do the bypass valve?
@JoseFlores-fm3bm
4 жыл бұрын
I would do the bypass valve since it does get pretty cold up their , down here in Texas it does get cold but not to the point that we need one , but yeah I would recommend the bypass valve so you can get the transmission fluid up to temp and prevent it from running to cold
@405ruben
4 жыл бұрын
Jose Flores okay thanks 👌🏽
What gauge cluster do you have? Looks awesome!
@JoseFlores-fm3bm
3 жыл бұрын
Thank you !Came of and 04 Escalade
Do you plug the fittings on the bottom of the radiator ? Does it leak if you don’t?
@JoseFlores-fm3bm
2 жыл бұрын
I dint plug the holes no leaks
Did you plug the return line on the radiator? The top line on the radiator.
@JoseFlores-fm3bm
4 жыл бұрын
No just cleaned the remaining oil
how has it been running?
Does the transmission temperature gauge just automatically start to work even tho your truck didn’t come with that gauge ?? The ecm will make the gauge work ?
@JoseFlores-fm3bm
4 жыл бұрын
Yes as long as it’s for the same year , mine came of an 05 Escalade but any Escalade with the tranny temp or 2500 hd from 03-07 classic models will work , just a cluster change
@MatCran
2 жыл бұрын
@@JoseFlores-fm3bm , wait a minute, all I need to do to get a read out of tranny temp is switch my gauge cluster to a matching year cluster from an escalade? This is really sweet if true.
What did you plug the old radiator holes with?
@Bassingtv
2 жыл бұрын
They sell threated caps at any hydraulic hose shop
That's kinda a rare truck. rcsb z71 I want one
Clean install thanks, hey Do you think is the same one to install it into a 2009
@JoseFlores-fm3bm
3 жыл бұрын
Thanks , and it should be the same just mounting would be a bit different
Did you have to add transmission fluid after the installation?
@demarcusbody9437
3 жыл бұрын
No
I’m having a hard time finding a black one. Is the silver noticeable through the grill in person?
@Michael-nu1py
4 ай бұрын
Paint it
Did you plug up the holes in the radiator? I'm in Texas also, so no need to heat up the fluid first. LoL, this heat is insane.
Do you need more trans oil since it’s more bigger ?
@JoseFlores-fm3bm
4 жыл бұрын
Yes I added a bit since I had lost some when I disconnected the lines , but just top it of once everything is done
Nice vid carnal, but that engine sounds like it needs some work.. I hear knocking noise.
@JoseFlores-fm3bm
3 жыл бұрын
It’s a Chevy I’ll be fine 😅
I got a question. I have the 03 cateye 1500 non hd. Is it posible to install the hd grill without having to have the hd hood?
@justinwilliams7008
2 жыл бұрын
There will be a gap
@justinwilliams7008
2 жыл бұрын
The only difference I think is the cowl induction that the hds have
What about that old line to the radiator do you just leave it open or cap it ?
@jameschaplin8975
Жыл бұрын
Did he cap the old line to the radiator?
hey bro nice vid, did your engine go over 210 at times when you had the stock cooler? and if so did this fix it?
@JoseFlores-fm3bm
3 жыл бұрын
Yes my engine did go over 210 twice from a bad water pump and a blown radiator line and both times I saved my transmission from overheating
@armandodiaz6744
3 жыл бұрын
@@JoseFlores-fm3bm oh bet I have an 06 gmc with a 6.0 cammed headers and sometimes my engine temp goes over 210 but instantly goes back down and I can’t figure out what it is
@JoseFlores-fm3bm
3 жыл бұрын
Does you truck come with electric fans ? If not you can do the electric fan conversion and run a colder temp thermostat
@armandodiaz6744
3 жыл бұрын
@@JoseFlores-fm3bm yeah it does have electric fans. And a new water pump and radiator. You think it can be the coolant that’s old?
@lordbox4496
3 жыл бұрын
Put a 160 thermostat
What temps you getting after the install? Any improvements
@JoseFlores-fm3bm
Жыл бұрын
150 -160
Do you need to bleed the system since air is introduced? Or will it work it self out
@JoseFlores-fm3bm
4 жыл бұрын
It will work it’s self out
Think the right way would be with the inlet and outlet inserts facing up, because if not you will be only using actually 50% of the tru cool😞
@JoseFlores-fm3bm
4 жыл бұрын
Well I’ve seen a lot of people installing them the way I did and others upside down but they never say how much of a difference it made temp wise , me before the tru cool I was at 200-210 and now I stay at 150 all day long under normal and hard accelerations, till today it still hasn’t gone above 150 ,I’m not saying this method is better it’s just I haven’t seen anyone post before and after with the tru cool upside down
@Squeeks713
4 жыл бұрын
Jose Flores we’ll noted thanks
@eldog263
4 жыл бұрын
I spoke with the distributor and they stated that installing the cooler with the lines to the bottom actually maximizes efficiency.
@streetlifefilmz8495
3 жыл бұрын
@@eldog263 so thts better
What's the long cooler to the right of the radiator for
@JoseFlores-fm3bm
2 жыл бұрын
Power steering cooler
Is there any advantage to using both trans coolers OEM and aftermarket?
@JoseFlores-fm3bm
4 жыл бұрын
If you mean using the main radiator and after market cooler no and yes , it will help the transmission fluid temp rise to operating temperature quicker but if your motor over heats both the motor and trans fluid will over heat , had that happen to me twice but not anymore with this set up
@MichelLinschoten
4 жыл бұрын
It’s the best way to go no matter what he says
do u cap the trans inlet to the main radiator?
@JoseFlores-fm3bm
4 жыл бұрын
No just cleaned the remaining oil
i have a dropped silverado like yours, is it recommended to do this?
@JoseFlores-fm3bm
2 жыл бұрын
If your beating on it or use it for street yes highly recommend
Do u know if this will work on a 03 avalanche that didn’t have a trans cooler factory
@joeyjimenez99
13 күн бұрын
yes im doing mine
What did you plug the holes with on your radiator where your disconnected the lines
@JoseFlores-fm3bm
4 жыл бұрын
I dint plug them up , left them open just let the remaining fluid drain and clean afterwards
@christopherhendricks4369
4 жыл бұрын
You don't need to plug them. I actually have plugs from a radiator I bought since my factory one leaked. But you don't need it plugged
@j.cooper2246
3 жыл бұрын
@@christopherhendricks4369 yes.plug off old holes to keep debris out of radiator. Trans fluid is flammable and its only 2 plugs.go to a junk yard and cut the ends off 2 old lines, cap them off and install in radiator. Done.clean.
Do you have to plug those transmission connections on the radiator or is it fine like that?
@alexletner8796
3 жыл бұрын
That’s what I was wondering
@Titoo.1
2 жыл бұрын
No answer?
@mattshelley3868
2 жыл бұрын
Any answers on this?
@Titoo.1
2 жыл бұрын
@@mattshelley3868 took them off left unplugged I'm pretty sure it didn't leak after
@mattshelley3868
2 жыл бұрын
@@Titoo.1 appreciate it man
did your fingers burn at 8:53? 😭 thanks man helped out a lot
@JoseFlores-fm3bm
4 жыл бұрын
Tbh I probably did lol can’t remember but I’m glad it helped out , if you have questions feel free to ask
Nice rig! What cluster is that man?
@JoseFlores-fm3bm
Жыл бұрын
Escales 05
By any chance do you have part number for this exact one? Or the link to where you got it from thanks!
@Zyphen4866
2 жыл бұрын
just amazon trucool 40k, there are two, one has the bypass valve and one does not, price will tell you if it does or doesnt
@cristianSanchez-ln6pu
8 ай бұрын
@@Zyphen4866is the one with the bypass valve better?
what did you use to cap the radiator?
@obslife1985
Жыл бұрын
U don’t have to cap the radiator where the transmission lines were going into. that spot is just for the transmission fluid to heat up…..u can leave them open if u want……no radiator fluid will enter or exit out of that
So you're not running it to the radiator no more ? I just installed mine and the guy said we shouldn't connect it to the radiator as well I also got the true cool 40
@JoseFlores-fm3bm
3 жыл бұрын
Nope straight from the transmission to the trucool itself setup , runs cooler and will prevent the trans from over heating if the engine happens to
@sonny62denali
3 жыл бұрын
Thanks for the info bro
Great video !! can I use that system for my 2003 yukon denali bro?
@JoseFlores-fm3bm
3 жыл бұрын
Thank you and yes you can their both similar
Did you plug the hole where you deleted the transmission line from the radiator??
@JoseFlores-fm3bm
4 жыл бұрын
No just cleaning the remaining oil form the radiator
@evokezyy5775
4 жыл бұрын
@@JoseFlores-fm3bm so they stay open?
@JoseFlores-fm3bm
4 жыл бұрын
Yes
@evokezyy5775
4 жыл бұрын
10-4 great video
Does the cooler allow the fluid to get to the right temp in the winter?
@sharpie132
3 жыл бұрын
No that's y he bypassed the radiator.
What did u use to plug the radiator
@JoseFlores-fm3bm
4 жыл бұрын
I dint plug mine up just cleaned the remaining oil on the radiator
Any update on the trans? Has it lasted?
@JoseFlores-fm3bm
Жыл бұрын
Still running strong couple of burnouts and digs and still doing great lol
Hi I have hummer h2 2003 I wanna install true cool so process same ?
@JoseFlores-fm3bm
2 жыл бұрын
Should be almost all the same just on taking of the grill pretty much
I'm keeping the radiator cooler on mine. Maybe if the temps aren't as low as I want I'll bypass it. Not sure yet.
@JoseFlores-fm3bm
4 жыл бұрын
Sounds good , if you have more questions lmk
@christopherhendricks4369
4 жыл бұрын
@@JoseFlores-fm3bm working on mine right now actually. Fluid overheated awhile back when I was on a steep back road. The factory cooler isn't nearly good enough for Arizona summers.
@JoseFlores-fm3bm
4 жыл бұрын
Yeah factory cooler sucks on these trucks but I’m glad your switching over to the 40k that should help out a lot
@christopherhendricks4369
4 жыл бұрын
@@JoseFlores-fm3bm got mine installed. Not too difficult. Not liking the compression fitting too much may need to make a new cooler line without the fitting.
10:16 why would you need to remove the line? just shove the end of it into the rubber hose that came with the cooler and use the included fitting to connect the rubber hose to the cooler it self and you're good to go
@JoseFlores-fm3bm
4 жыл бұрын
I removed them because I wasn’t going to use them , i ran the lines straight to the 40k instead of having the transmission fluid circulate thought the main radiator plus If the motor ever overheated I know the transmission won’t overheat , had that happened to me twice , but not anymore
@jalawialotaibi3877
4 жыл бұрын
@@JoseFlores-fm3bm clever
@Papisartee
2 жыл бұрын
@@JoseFlores-fm3bm did you need special fitting to plug the radiator? Or did it just stay without lines? Thanks for the info G
Either way the rad it hotter then the 4l60 likes 200 -210 the heat kills em they r best around 160-180
What if I still want have that line to the radiator. Because here it gets cold
@joelsalazar3332
3 жыл бұрын
just connect it in series. would be fine
@JoseFlores-fm3bm
3 жыл бұрын
Yeah I would recommend what he said since it’s colder up there
part number?
What is this part # nice vid bro
@JoseFlores-fm3bm
3 жыл бұрын
Don’t remember but amazon has them around 160
Water cools better than air, you need both man
This MIGHT be a stupid question, but I'm a teacher and I ALWAYS say: the only stupid question is the one not asked. So here goes: why does a vehicle need a transmission cooler?
@JoseFlores-fm3bm
2 жыл бұрын
True lol and no worries a trans cooler helps extend the life of your transmission specially on a modified vehicle, it helps keep the transmission fluid temp stay cool since heat is the number one transmission killers lol
Would connecting a fan to the cooler be best I installed the same way as you did and everyone else
@JoseFlores-fm3bm
4 жыл бұрын
If you have your transmission cooler in a different location for example underneath the body of the truck or in the bed of the truck then yes a fan would really help but up front it won’t need it , it gets plenty of air flow
@GG-zd4yd
4 жыл бұрын
Jose Flores what if I’m at a stop at a light how is it getting air flow
@JoseFlores-fm3bm
4 жыл бұрын
I have my set up on my daily driver and it never goes above 150 all day long with and without traffic
@MichelLinschoten
4 жыл бұрын
G G there is a huge fan always running ... it draws air in at all times. Do yourself a favor, let someone else do it you are clueless 😂
How much cooler does it keep the trans fluid?
@JoseFlores-fm3bm
Жыл бұрын
150 - 160 on hot days and 17-180 when your beating on it lol
@jesusfavela3434
Жыл бұрын
@@JoseFlores-fm3bm how hot would it get before the cooler?
@JoseFlores-fm3bm
Жыл бұрын
@@jesusfavela3434 190 cruising 210-215 towing
Does it matter which way we run the lines to the trans cooler
@JoseFlores-fm3bm
4 жыл бұрын
No oil may flow in either direction through the cooler
@fearthisperformance9553
4 жыл бұрын
@@JoseFlores-fm3bm thanks bro and one more question when I remove the trans lines from the radiator will I need to plug them
@JoseFlores-fm3bm
4 жыл бұрын
FearThis Performance no plugs on mine just drained and cleaned the remaining oil
@JoseFlores-fm3bm
4 жыл бұрын
FearThis Performance and no problem if you have more questions feel free to ask
@fearthisperformance9553
4 жыл бұрын
@@JoseFlores-fm3bm thanks alot bro
For what is the bypass valve?
@JoseFlores-fm3bm
4 жыл бұрын
The bypass valve is used to get your trans fluid temp to operating temp when weather in the low 40s or so , if you live here in Texas your fine with out it lol
@fernypaletas7148
4 жыл бұрын
Jose Flores all right haha
@1sixkobstahoe138
Жыл бұрын
Yo what about here in Houston this weather be bypolar
What do you put in the radiator for the thermal bypass when you run the lines straight to the cooler? Is there any plugs or something I need to buy?
@JoseFlores-fm3bm
4 жыл бұрын
You can buy the transmission cooler with the thermal bypass or if your running the lines like me you can just removed the lines from the radiator and let it drain and clean the remaining oil , that’s what I did and so far it’s been clean no spills and no caps
Where can i buy it?
@JoseFlores-fm3bm
3 жыл бұрын
Amazon has them for under 200
Great video...Wouldn't it had better just to delete the trans thermostat...? kzread.info/dash/bejne/pKOlpqSegpmfkcY.html did you have to buy more hose for that.. did it come with plug to stop the oil from leaking out from the lines you removed..
@JoseFlores-fm3bm
4 жыл бұрын
Never heard of a trans thermostat on these trucks before and the trans cooler came with about 3 ft of hose , dint use more than that , no plugs came with the trans cool
I was told this cooler works best with the lines up other wise you’re not getting the the complete cooling benefits of it.
@danielanguilm2285
3 жыл бұрын
The stock cooler (same type, just smaller) is mounted hoses down.
@russellschroeder990
2 жыл бұрын
I totally agree. Obviously there was nothing in that stock cooler. It all ran back to the trans. Hoses up would be the best way to insure all the tubes get filled. In my opinion anyways the factory don’t care about our stuff
Where’d you get that cluster man?
@JoseFlores-fm3bm
3 жыл бұрын
04 Escalade