I know that as of today this vid is almost 4 years old, I watched it when it was new. I just bought one and this information was priceless. Sometimes you never know when you'll need information like this and knowing where to look is key. Thanks Harvey.

You are the best teacher I have seen on thje net!! Thanks Harvey!

Thank you!!! I just got a brand new wiring harness for my 110 and installed it and it had no spark, so I got to 111 in your video and saw the part about the yellow black wire on the cdi going straight to the coil, and looked over my wiring again and saw that I had the cdi plug plugged into the hand control and the hand control plugged into my cdi, now I’ll change em around. Thank you so much, your a life saver

Damn! After all these years I finally understand it! Presented in the Exact format in which I learn. Thanks!

By the way thanks for the video on wiring that up. U the only person i have found that knows what he is talking about when u are explaining your technique!! Thanks again bro

I like the way you explained with the basic 12 V with the scooters and the quads doing a good job I've been mechanic for years and just started playing with the scooters and these Chinese wiring is so undependable keep up the good work you got my vote

Awesome info. Great to have someone such as yourself able to explain things in simple english.

I just snagged a SUNL ATV-109 today from a co-worker that needs to have the battery charged, carb cleaned and a good romping to clean out the cobwebs. Maybe not in that order. He also told me that it runs great for about half an hour, then it shuts off and wont start again until it cools down. I've watched a couple other videos and done some research but your video not only laid things out better than everything else but also made more sense. Thank you!

@HarveySpooner

7 жыл бұрын

Hey INECIKlavier!!! Sound like U got a great deal!!! About heating up and shutting down, could be Ur CDI or spark coil, but, before U mess with them, I would make sure the gas flow into the carb is good, I have running across a few smaller China carbs where the bowl fills very slowly, especially when the motor gets hot, had something to do with the float needle valve, I just swapped them out.... Good luck with Ur new ATV, enjoy it!!! Thanks for the info, encouragement, watching, and commenting!!! Please let me know how it all turns out....

Dude, you ROCK! I can't find shit for info on these until I found your video and got a deep understanding. Can't thank you enough for making this video!!!

I have an Alpha Sport Cobra 180. I was told all it needed to run was a new wiring harness. I was given two harnesses with it. Hopefully, the information you provided here will help me get closer to getting my quad to run.

Once again I come to you for instruction,your the man Mr. Spooner! THANK YOU VERY MUCH AGAIN!

@tyrekburden5892

Жыл бұрын

I have one that has a green ,blue and white , a black and red and two yellow where do or what to I hook the to yellow up to

Mr Spooner you are very kind for sharing your expertise on this topic.. keep it up. And thank you.

@HarveySpooner

6 жыл бұрын

Hey Randall!!! I'm just trying to keep as many ATVs out of the junk yard as possible, even if they were made in China!!! Thanks for your kind words, encouragement, watching, and commenting!!!

@randallhighsmith3406

6 жыл бұрын

Harvey Spooner got a 07 Manco talon 260 .. been trying to get this thing running consistently.. replaced all components. Even bought the dc Cdi that you use haven't hooked that up yet.. what a headache

Harvey thank you,I bought a Honda 110 for fifty dollars . Pretty much complete. It even had the tools,that are kept on the frame .The fenders were just faded a bit. I could not get spark I worked on it for about 6 hours and I came watched your video and you said you got no ground you got nothin. So I ran ground wires everywhere and by gosh I got spark and it started up right away. I thought it was grounded all ready but it wasn't. The bike had set in a Barn for over 15 years . Just think just because of a Ground wire . Thank you. Oh I also have a little Chinese quad 110 and a 250 They are okay could be better if they made their frames stronger. I

@HarveySpooner

6 жыл бұрын

Hey Lonnie!!! I love hearing stories like this, another Honda ATC saved from the scrap heap.... Good job taking the time to figure everything out!!! Thanks for the info, encouragement, watching, and commenting!!!!

Good job Harvey...interesting tutorial.

I'm sure many people will have lots of fun on their bikes after you helped them to repair it

@HarveySpooner

8 жыл бұрын

Hi Simms, I try to keep ATVs out of the scrap yard, even the China ones!!! Thanks for the encouragement, watching, and commenting!!!!

Awesome ! Seriously, thanks bro. I wished I found this videolike two weeks ago

This is an awesome video especially for someone that might not understand ignition systems too well. You're a great teacher and well thought out. I'm subscribing!! "It's a good idea if you like getting hurt because it's probably gonna break and you're probably gonna crash so... whatever gets you through the night I guess."

I have this engine with the same electricle problems but it has a 50cc head instead of a 70cc or 110cc head! But thanks for helping me fix my engine!

Thanks for the info. My problem was a corroded kill switch causing resistance in the Run Position killing the spark.

Once again Harvey, I'm up and running thanks to your tutorial !! You are da man !

@HarveySpooner

6 жыл бұрын

Hey Bruce!!! The next version, the newest generation of the portable CDI system is under development, it is high performance and rechargeable.... I should be putting a video up on it soon, stay tuned!!! Thanks for Ur encouragement, kind words, watching, and commenting!!!

@brucemanly7857

6 жыл бұрын

Are you kidding me, I wish I could pay back the knowledge and experience that you so graciously give away, I USE these vids in place of a service manual, do you have any idea what those cost?!?!? Thank You Harvey, don't thank me I only profit from the tips and short cuts, by not having to pay a guy to sell me advice, with a fraction of your wisdom and know how.....you're much appreciated !!

@HarveySpooner

6 жыл бұрын

Hey Bruce, Thanks for all the kind words and encouragement!!! Thanks also for Ur thoughts, watching, and commenting Bud!!!!

Very good Professor, you know your wiring inside and out. I have taken notes. Take care

@HarveySpooner

8 жыл бұрын

Rusty, I have ATV wiring down pat, I just need to work on my fabrication skills, that is what I learn from you!!! Thanks for the kind works, watching, and commenting!!!

Very well explained! great details, and great video, you earned another subsciber!

Thanks that was a great help. greatings from Denmark

@HarveySpooner

5 жыл бұрын

Hey Tommy, Thanks for the Kind words from Denmark, I would love to visit your country one day!!!! Thanks also for Ur thoughts, watching, and commenting, I'm glad that my videos have been helpful to U!!!

Thank you so much. The way you explain this is so easy to understand. I really appreciate it.

@HarveySpooner

6 жыл бұрын

Hey Joe!!!! I'm trying to save as many of these things from the scrap yard as possible.... Thanks for the positive feedback, thoughts, watching, and commenting!!!

@firemoth

6 жыл бұрын

Harvey Spooner I started following your how to today. So far I have the engine off the frame...i have two of them, and I'm trying to put together one working engine. Is the coil pack for the spark twelve volt? I ask because I need to know if I can rig it up with the jumper or if I need to have it connected to the converter

@HarveySpooner

6 жыл бұрын

Hey Joe, For a Capacitive Discharge Ignition, (CDI), system the only power to the spark coil is the output from the CDI box, the CDI box maybe powered by the battery, (DC CDI box), of from the stator, (AC CDI box),... I will be doing some wiring on the Jonway 110cc mini quad over the next week or so, please stay tuned.... Thanks for asking, watching, and commenting!!!

any info on removing/eliminating wireless receiver [ wireless remote kill switch ] from wiring harness? thanks

It's really nice of you to take your time to sit down and do this video just for others. I for one thank you, even thought it's not for me. Everyone needs a refresher course from time to time. Thanks

@HarveySpooner

8 жыл бұрын

Hey Calvin!!!! I'm glad that U enjoyed the refresher class, now, for extra credit, what was Ur favorite hard cider? Was the pear cider as good as U thought it would be????? Thanks for the encouragement, watching, and commenting!!!

@CalvinsCorner72

8 жыл бұрын

+Harvey Spooner OK the Pear was good but not like I thought of when I have Pears. Pears are sweet but this Cider was sour a little but good. Thanks

Pretty good explaining video pretty helpful my still not runing but, but after wach this I know there is a hope to Bring it back to life, thanks 😉

@HarveySpooner

8 жыл бұрын

Hey Aldo, Thanks for all the kind words, U may check out Must1, Darren does a really good job with his video and explaining of repairs, between he and I, we will help U almost anything fixed.... Thanks for Ur thoughts, watching, and commenting!!!

Great vid. I got one question though, I bought an aftermarket wiring harness, but the red (power) wire from the battery is pretty thin. Is it possible that it's not thick enough to pass the current to the rest of the wiring harness ?

hi harvey thanks for the video i followed it and my wiring is identical to the one you have in the video. i was able to get the lights/horn an starter but i still get no spark to the plug. will be replacing the CDI next. but not sure what else to check on. got this from someone that has had it sitting out for a while so slowly getting back into running order.

Hello Harvey - i have found your videos quite helpful - i understand the basics but solid state ignition systems were always a mystery to me - thanks to your videos i now have a clue when it comes to CDI. I have a chinese quad - i believe 110cc - not starting. Kick start is broken and only use electric start. There is spark as starter first engages but then stops as cranking continues. I followed your troubleshooting and red wire out of the case - it is there but not connected - has an insulated female lug that goes nowhere. Come to find that the cdi gets 12v dc somewhere from the battery circuit. When i crank i see the voltage to the cdi drop to about 8vdc. I measure the power from the case as 50vac - should i connect that direct as to the cdi power (black/red)? Any other recommendations?

Thanks dude. Removed the white black wire coming from the ignition lock and it worked.. it seems that the ignition lock dont work right anymore and the black/white is all the time on off

Hi Harvey. I really enjoy watching your videos. You mentioned the gy6 DC in this video. I have a gy6 150cc buggy that is 12VDC.....my question is it has a voltage regulator and I'm wondering what it does when the voltage coming from the stator is DC? Most, like you said, turn the 12vac into 12vdc to charge the battery so does that mean that on a DC stator, that the voltage regulator isn't needed or does it do something else? Thanks

Great and informative thank you all the best for your future

very helpful informations, thanks man.

Harvey I have a question. Do I need to leave the battery hooked up to the atv after starting or is ok to start it up and removing it. Thank you Harvey.

Juat what I was looking for . . thanks

I’m going to try your diagnostic. I really wanna learn these Chinese quads.. its interesting ..

I have a question about my jeep style 125cc go cart. I can turn the key and I can hear the sound of the starter but that's it what would it be

Good video Mr. Spooner

@HarveySpooner

8 жыл бұрын

Hey Terri, Beautiful day today to be outside!!! I manage to cut the lawn today without breaking the Murray Tractor, I used the Deere!!! I figured this video may keep a few ATVs out of the junk yard... Thanks for the encouragement, watching, and commenting!!!

@michaelbarry7630

7 жыл бұрын

wtbm1

2008 50cc scooter won't start. Ran in 2018. So-so start but got it running. Ran OK for 3 months. Couldn't start one day to go to work. Ugh! Things I've done. - Checked battery volts = 12.5V - Installed new spark plug = good spark - Installed new carb - New gas filter. Checked gas flow post-filter using cylinder vacuum = Good flow. Now what? Stumped. After installing carb, do I need to prime? Doesn't look like gas is getting to spark plug. Plug looks dry. Any suggestions or questions? Thanks for the support!

Great video! Very easy to understand. I have a 2010 Gio 200cc atv. I'm having trouble with intermittent spark. Every reading is good. My black red is only 295. My blk yel is only getting .5. New cdi blk yel got 1.1 now only 0.5. Any help or suggestions would be great. I'm thinking cut everything out and start over? Looks like someone was experimenting with subpar connections/splices.

@user-wg3cj4qx3z

9 ай бұрын

14:01

This is so good! Thank you so much!!

Great video and instructions.

Great video Harvey. I have a question for you. I have a 2006 hammerhead 250 go kart that I am not getting spark on. I bypassed the kill switch and the ignition to make sure it was not the problem. Still no spark. I cut the black and white lead coming out of the CDI and when I touch the wire with my fingers the spark plug has a continuous spark. I am assuming this is some sort of grounding problem. Would you agree?

Hi Harvey, I saw your video and it has helped a lot. First of all I have a quad MPX 150 and it had a spark once (just one I saw it with a test plug but no more). I have checked the wires you mentioned and they check good (ohms, continuity, etc...) but I have a wire I can't determine where it goes. It is coming out of the engine in that five wire configuration you talked about and it is Red/Blk stripe. It has a single female terminal but no other male anywhere to be found. It reads 400 ohms. HELP!!!!!!!!!!!!!

videos have all helped. i have a request, i am in the few with a chinese gy motor made by lifan. trying to find information on it is rediculous and u mentioned it. what makes it different? mine is the 150 or 200cc enduro and the wiring i redid to cut out the extra wires. its my first bike and i think im making it harder then it really is. im familiar with cars and work on my jeep. @12;12 is where u mentioned it. thank u for the great videos

Hi,I m glad u r a good teacher I have a a 49cc Yamaha scooter

@Ahmed-kk1cg

8 ай бұрын

I have a 49cc Yamaha 1988 scooter I was just wite the cdi to motor from motor is black white yellow red n white and from cdi is black,red n white,black n white,black n red, so black is going black and also ground then coil,red n white is going red n white,then black n white is kill switch there it's go and second black n red there go because from motor these two I Don't have it plz can u help me so I can start without battery and I know from motor white and yellow white for light I m not using that two,I need here a switch or lagulater here where kill switch and and black n red wire go because I Don't have spark Plz help me if u have time

Really good video brother thank you 😊

Good vid mate - solved my issue.

Hi good video I'm working on one of these at mo 50cc semi automatic. Got a weak spark or no spark at all . I'm suspected stator so far but unsure of the output voltage. In my case (red and white trigger wire) (red and yellow goes to the cdi main) (Green and white is earth) ( yellow to rectifier) and (white to rectifier) .What should be roughly the voltage on Cranking best Regards James

looking forward to seeing you work on the cushman

@HarveySpooner

8 жыл бұрын

Hey Roger, The Cushman Minute Miser will be a build type video.... I need to spend some time trying to fit everything under the seat.... Thanks for your thoughts, encouragement, watching, and commenting!!!

@eddiecruey9989

7 жыл бұрын

Harvey Spooner hey buddy I have a hawk 250 enduro, 2015. I can't get a spark. Following ur video I checked ohms and it was good till I checked my stator wires the black and red is the only wire that gave me anything. The other three the is nothing. I don't usually comment on video's, I don't know how to get a notification for the reply. However if u will please contact me threw facebook Eddie Cruey . Or just text or call Please I would be so appreciative . 919-824-9609. Thanks in advance

Hey I have a question, I have 4 wires coming from my engine which are 2 gray wires and a black wire then a white wire what do think I should?

Harvey I need your advice, I have a 90cc 4 stroke believe it's a kazuma engine. I recently replaced all the wiring, along with stator, rectifier, coil, starter solenoid, ignition switch, everything due to some wires shorting out. When I replaced everything,it fired up in 1st try, a couple days later it wouldn't start. Had low compression, so I tore into the top end to check everything. Ended up replacing head gasket and stuff. Found both valves,so took them off, removed all the carbon and re installed, and adjusted the valves. Re installed engine, put everything back together, and I have no spark. Checked all the connectors, all "look" good. I have a multimeter but it's too fancy for me, can't figure out how to use it 😂. What do you think it could be? Thanks.

Im gone put the Quad on the table one of these days , so thanks

@HarveySpooner

5 жыл бұрын

Hey Paul, Good luck fixing Ur quad!!! Thanks for Ur thoughts, watching, and commenting!!!

hey Harvey I'm working on a Suzuki Eiger lt-a400fk and I was wondering if the pit bike cdi system on one of your outher vids would work for that

I appreciated the video. Can you tell me what to do with the information I obtain? I'm not getting a spark. After I identify the wires, ensure there is spark, test the ohms, what is next?

I have a modified honda cub that has a 125cc hondamatic, it got soaked by sprinklers one night and hasnt started since, its kickstart only. I ended up replacing my cdi, coil, plug, reg/rectifier and still no spark? Thanks for helping all of us!

I have a 2008 Baja 110cc quad. I'm getting fuel and spark. Starter and solenoid are new. New spark plug as well. My problem is, it cranks and cranks, but doesn't turn on. Everytime when it cranks, you can hear some noise from the exhaust (like a popping noise as if it wants to turn on; with the choke closed AND opened). But, I bought this from an amateur mechanic who, which had appeared to open the valve end of the engine, and who also stripped the spark plug entrance (it goes in fine all the way with a rachet and in small areas, it tightens up, but it keeps spinning when you try to tighten it on the last thread). I have yet to use a multimeter, but I will be buying one tomorrow. I've only been using a fuse checker (one of those tools w/ an alligator end that lights up when you touch power)

Hey man I'm not getting a ground out of my green wire from the stator. Do you know what could be the issue. It's a universal wiring harness and I can't seem to figure it out

man you are awesome .. ilove you ❤️🌹 i really appreciate your works and i like your videos , ifind them really helpful .. thank you and keep going 👌🏻😘

@HarveySpooner

7 жыл бұрын

Hey Mixerhd3, Thanks for all the kind words, I'm glad my videos help you and hopefully they have saved a bike or 2 from the scrap pile!!! Thanks again for the kind words, encouragement, support, watching, and commenting!!!

Can I know where the black wire comes from that’s on the ignition coil cover?

Hi Harvey , I was wondering if i could get your advise , i have a 110cc China Quad , it screwed up a couple batteries so i invested in a higher quality one and then i changed all of the Ignition parts , CDI , Reg everything , still appear to have no spark but it turns over ok , scratching my brain now trying to work out why it wont kick , any advise would be grateful , i enjoyed your video

@HarveySpooner

7 жыл бұрын

Hi Casper, Seems that U R telling me that your quad was killing batteries, U improved the battery situation and U replaced the CDI, Voltage regulator, and ignition coil and now it will not start... If I understand Ur situation, the first thing I would do is go back to the OEM CDI and ignition coil... If still no spark, I would disconnect the engine off wiring, (the black wire with the white stripe from the CDI box, cut or remove it in a way such that it can be hooked up again), and see if U get spark again.... Some of the CDI boxes use AC, others use DC, so, changing the CDI box may have killed Ur spark, removing the engine off wire will tell U if the problem has to do with the wiring.... Let me know how it turns out.... Thanks for asking, watching, and commenting!!

@Casper_Brisbane

7 жыл бұрын

the carby was completely stuffed after i replaced it the quad is roaring back to life

@chriswise608

6 жыл бұрын

Casper The Ghost *

@jamescoey7922

6 жыл бұрын

Sportster wiring

Hey Harvey, good video. I just picked up a Zongshen ZS125ST ATV for free. I want to get it fired up for my kids. The motor cranks but doesn't kick. The wiring harness is all hacked up and I think there is supposed to be a radiator or oil cooler or something? There certainly is definitely something missing. I'm solid with the wrenching and the electrics, just not sure where to start on this thing. Do you know where I can pick up a manual so I can begin finding parts to piece this thing back together? Thanks.

@HarveySpooner

7 жыл бұрын

Hey Brad, Can U make a video of it, to be honest, I ran a couple of searches and I did not find anything that I would trust, having said that, it seems that the engine maybe a transplant from a Zongsten scooter, if that is so, U may have some more luck getting a manual and parts. Look up Zongsten 125cc scooter, (I'm assuming 125cc, use the correct engine size in your search), Thanks for asking, watching, and commenting!!!

Bro im a airhead and i was wondering if you could show me exactly where to hook my wires up to if i showed you a pic of wat wires i do have

so if my engine say 48 m3 on the head its a 50cc? i thought it was a 90cc let me know im very interested in how you can tell by the engine

@TerrorTales4271998

3 жыл бұрын

@@jonishaan6626 you guys got reported for being scammers

How do I bypass the key switch. It has four wires white black red green. Thanks for the help

I have a 125cc coolster when I go to turn on the key switch some of the wires start getting real hot to where it melts the plastic insulation off the wires . What could it be.??

hey is this same as a gio beast 200cc I cannot figure it out for the life of me previous owner hacked it up

Hi Harvey.. Thanks for the video. I'm replacing a stator on a 95 Honda elite 80 scooter. Found an aftermarket China made very close but may have to swap a wire. How can I find out if my scoot is AC fired?... Thanks.!

were dose the earth go left or right of the starter motor ?.

Very interesting mate , what do i need to do to run my bike without a battery ? just using the kick start ? Its got a Honda 110 engine in similar to your quad engine Do i need to fit anything or join any wires together cheers ✌️✌️

Harvey,I have a 2015 Velzo 125 Atv. My problem is when I turn the key to the start position , I get nothing. I replaced the battery and still nothing. Your thoughts! Thank you

I’ve got power from black and red.hooked everything up as explained and still have nothing.it was all wired fine untill I put the jump pack on now I’m just getting nothing any suggestions.and if I’ve got power from the stator does that Jean everything under the stator is fine

Which voltage is suppost to be generated by the puslegenerator? I´m not sure if mine is broken.

hey Harvey is this the same as a 200cc we cannot figure out my gio 200cc ATV

Can you help with transmission issue? It takes forward and reverse but it won't pull. Please help

Yes I do but the thing is that I tested every thing the stator, coil, spark plug you name it, it's just not getting any spark

@HarveySpooner

8 жыл бұрын

Nick, Given that U tested everything and got good readings, I would disconnect and float the on off wire and hook an extra ground between the motor and frame and wire harness green wire and the ground on the spark coil just to be sure, if no spark, Ur CDI must be dead... Should cost around $15 on eBay.... If U live near the Hudson Valley of NY, I could look at it for you... Let me know how it all turns out.... Thanks for the info, asking, watching, and commenting!!!

@putonthearmerofgod2037

3 жыл бұрын

@@HarveySpooner hey boss I have a 125 pantera motorcycle and my cbi box got on my muffler and got burnt can I bypass it

hello Harvey , I have a 250 quad , and I have 4 wires coming out the engine , 3 yellow 1 green , I ideas what they do , as I have no spark

Hi help needed asap !! Ive recently purchased a new loom but plug on from stator doesn't match up to one on loom ive cut both plugs of now and am going go join them up then tape them off which colours go to which ??

@HarveySpooner

7 жыл бұрын

Hey Darren, Assuming that U R replacing one AC powered CDI for another, just match the wire colors and all should be good, blue and yellow, pulse generator, black and red, power from the stator, black and yellow, ignition coil, green is ground, and black and white should be engine off when grounded.... Let me know how it turns out.... Thanks for asking, watching, and commenting!!!!

How do I charge my 6 volt ? Nowhere to hook up, or just buy a new one?

How do i hook up a 4 wire keyed switch to start the 110 pocket rocket

I went through my 110cc China quad and got the same ohm readings as you did in the stator wires and the cdi except black and red. I have swapped in a new cdi and coil, still no spark. What is the likelihood that the stator is bad? Is there a way to test it?

Hey would you happen to have a wiring diagram for a TAOTAO Targa 150

hi Harvery the pulse generator doesn't have any power coming to it, but the others are live... what now? must I pull the engine apart?

Hello and Thankyou for your video I’ve got a loncin quad I’ve been working on. It’s on hold at the moment but I got it running and was ab oh t yo start painting it etc and all of a sudden no spark? Oh well I’ll get back to it soon

hey buddy I got the Arctic Cat 400 running I used to harness and the CDI and direct the prior off of my big bear Parts bike and hooked it into the the poster and the stator and it started right up

@HarveySpooner

7 жыл бұрын

Hey Theo, I guess the colors matched up? I am glad to hear that U got it running... Most of these components are similar and the ones from the China quads and pit bikes seem to get along with about everything out there, the artic cat and big bear parts must like that also.... Thanks for the info, watching, and commenting!!!

ok so i got a 1977 honda 90cc 3wheeler symple wiring but nothing was conected ar the head light and to beleve i got no sparck not to mentchion no cdi when i puled evering like the wiring has no way on one but i cant find any wiring diagram to hook anything proper and it came with out the head light im sure somthing is missing i just need the engin running for a gokart i built from ground up ive been on the gokart prject for 2 years now due to trying differnt engins non witch wold run due to wiring this is the typ of engin i want on it regard less cuz i want a manul gokart so i cant due the engin mount on it till i know i got a running engine that will run appon finishing the gokart putting the engine that rins in order to wire up the kart any help like step by step would be great.

Any ideas my stator has white, white red, yellow red, black red, black then my loom same as your stator Thanks

have a coolster while checking spark it sparks and then quits until you bump it again sparks about 5 times and quits again any answers are greatly appreciated

@HarveySpooner

6 жыл бұрын

Hey Joe!!! I would start by disconnecting the black wire with the white stripe from the CDI, (disconnect it such that it can be reconnected in the future), I have found that if the engine off circuit is active, it may spark a few times and then stop.... Let me know how this turns out.... Thanks for asking, watching, and commenting!!!

How do I splice into my harness to add the extra coil for my dual cylinder I bought a brand new china wiring harness that has a single coil from what I understand I can just slice into it??

hi i have a 2007 chinese panther 250cc zongshen engine air cooled manual trans it has the skater wires and another harness with 5 wires coming out about a inch from the skater and the new harness dont have them any ideas thanks ed

I have sparl when i take it out but when i put it back in it doesn’t start, im guessing it’s no spark issue but im not sure.

Can you do a video on how to set up a whole fresh new wiring harness on/off switch key switch & battery electric start on a fresh engine clean frame so we can see how to set things up ? You help but you not really hands on...

Is the white and blue wire for the pulse generator suppose to show that it’s grounded? I can’t get my son’s chins 110 cc started and I’ve replaced everything, checked all the kill switches, the only thing I haven’t done is replace the ignition switch.

Thank you for this video! i've checked every wire and all measurements are good except the red&black i get no readings at all, does that mean that the stator is bad?

@joylance7279

3 жыл бұрын

Mine is brand new rode it 2 times and now it is not sparking at all

@linusbewert8615

3 жыл бұрын

Turns out that the stator was bad, i bought a new stator and it worked great! until the crankshaft snapped off behind the clutch gear LOL..

I change the coil ,cdi, regulator and magneto and y has fire on the spark but just for a moment and no more fire again in the spark?

please tell me where the 2nd wire goes on pulse generator

Hey Harvey. Wanted to say thank you. Got my son's Tao Tao 110 running for the first time after 6 years of just sitting there. Pulled the kill switch wire from the CDI as you pointed out, sprayed some WD-40 in the carb and it started. Ordered a new carb from eBay for $15 and it starts right up, every time. Not sure which of the 5 or 6 redundant kill switches is the culprit, but hoping I can remove them all except for the key and the left side handle bar red button kill switch. Question: Assuming I can just splice the "kill" wire to the CDI to only the key and the red button on the handle bar and I'll be able to shut the quad off? In the mean time, using the carb's choke to kill the engine, which works every time.

I had spark yesterday bikes really mangled but I tried to get it going again today but no spark

Hey Harvey, white and yellow wires coming out of the engine, do u connect them to the battery to charge the battery???