2:52 for the start of the install

Give it a little tappy, a little taparoo, tap it in

@AcornFox

3 жыл бұрын

It’s all in the hips

I find that running around the table 3 time counter clockwise helps too. It has to be counter clockwise though! Then write 'trjicon' on some parchment and burn it then throw the ashes down a freshly dug well...yeah...uh huh...

@ThePartisan13

2 жыл бұрын

You seem agitated

When you said you were anal about installation I was thinking something more like a torque wrench.

@RichieValentine

2 жыл бұрын

What would the torque setting be?

@SpaeDed

2 жыл бұрын

Nope just a mallet lmao 😂

@SpaeDed

2 жыл бұрын

And some tapping??? Lmao

@josephjames6369

Жыл бұрын

@@RichieValentine 18 inch lbs per trijicon

Thanks for your video. Good info.

Great video ! Thx 🙏🏼

The Sage dynamics guy does this exact same method when installing rmrs except he uses a sledge hammer.

I saw on the DR920 War Poet handgun the extractor was redesigned so you can do full size screws on both sides. Planning on grabbing a war poet asap.

I find it weird that Trijicon recommends Duracell, but my RMO6 came with an Energizer.

@KineticConsulting

5 жыл бұрын

Yup. It's most likely a contract that someone high up made and the lower levels can't change.

When I put the battery in I put the month and year on that side of the battery. It lets me know just how long I have left that battery in the unit. I set up my calendar to replace them once a year but sometimes that lapse of paying attention allows those batteries to stay in for two years. When I open it I catch my mistake.

Neither Energizer or Duracell make lithium "watch batteries like the CR2032". Sony and Maxell make most of the batteries in the market and they also manufacture for other brands with their name on it. Energizers have the Made in Japan on the battery. I sell watch batteries and Japan makes the best so as long as it's a Maxell or Sony you are good to go and have a long shelf like of at least 5 years. Also the Chinese brand GP in lab test performed very close to Sony and Maxell so they are also a good choice.

I wonder have any other electricians out there done the lazy move by pulling a couple 6-32's from a switch cover and just snipped one down to size using wire strippers with the built in screw shears.

Hi Jon. I called trijicon once to ask about locktite on the screws and they told me no because of the possibility of getting locktite into the channel where the extractor plunger rides.

@yangp2k

2 жыл бұрын

@Emmanuel Goldstein yeah I still do put blue on..but I'm very careful not to slather the threads.

Shit i forgot to put the battery in... God damit

@Marlo722

5 жыл бұрын

Everett Thoman LO Fucking L!!! Haha

went with vibratite, the way it works made sense.

Where can I find a set of mounting screws that have the shorter screw

How does it do with water, being exposed like that on the bottom?

Good ole mallet..

@FloridaSpook

6 жыл бұрын

Great video! Thank you. I like the way you seated the RMR. Also the tune ups for the gen 1

While looking at the type 1 RMR and hearing they have connection problems you showed me the plate. Would you think that the "dimple" in that plate should go up and now down. Up to add more pressure to the battery. Putting it down against the slide does nothing for battery tightness. Your paper did that job. Ask around and see if that "dimple" is supposed to go up against the battery.

@marmachuk16

2 жыл бұрын

That's what I was thinking, too.

Would that plate work with a type 2? The website says for type 1 only but I’m curious

@fapgatfishing2737

6 жыл бұрын

Jon Dufresne well I bought one expecting to get a type 1 but they were sold out so I got a type 2 👀👀👀

Hey Jon, what back up sights are they? Do you know the depth the RMR was milled too? I really like how low yours sit while still being usable. Thanks

@KineticConsulting

5 жыл бұрын

I don't know the exact depth to this one. Dp custom can probably answer that. I know that Agency Arms mills to .150 if I'm not mistaken. The sights are Ameriglo Suppressor sights - bit.ly/2OfAVD3

@AustoBruh

5 жыл бұрын

@@KineticConsulting Appreciate the quick response Jon! Look forward to taking a class with you in the near future.

@KineticConsulting

5 жыл бұрын

@@AustoBruh look forward to having you as a student

@everettthoman2097

5 жыл бұрын

I use zev .300 suppressor sights great lower 1/3 cowitness

Have you heard of any issues with that bitter coating?

So do I need a rmr plate or can I just slap the red dot on screw it in without the plate?

@KineticConsulting

4 жыл бұрын

You talking about the sealing plate? No, it's not needed but I prefer to have one because I live in a humid area.

What are the correct length of screws? My slide is milled for 6-32 but the length was off from the screws provided by trijicon and the one side was on my injector pin.

@KineticConsulting

Жыл бұрын

Depends on who milled your optic. Some places mill at different depths.

Do those screws come with the rmr from Trijicon? Thanks for the instal video too!

@KineticConsulting

4 жыл бұрын

No, the ones supplied in the trijicon RMR box are too long.

@uhhohhoreo

4 жыл бұрын

Kinetic Consulting just bought the sight, but like you said, the screws are too long. Where can i buy the ones that fit??

@KineticConsulting

4 жыл бұрын

@@uhhohhoreo you can get them from Agency Arms

@fariseomartinez9998

2 жыл бұрын

Does your firearm come drilled with 2 holes or do you go to a gunsmith for this? Thanks

@mattymediocrity8255

2 жыл бұрын

@@fariseomartinez9998 You can buy an MOS system which comes with plates to match the footprints of all different RDS pistol sites or, the preferable way, you send your slide off to be milled specifically for your optic.

I got my slide machined from battlewerx and couple years have passed now and I cannot get my RMR off. When I installed it, it was such a tight fit I had to use a vice and some rags to slowly slide it in and not scratch it up. I tried the samething getting it out but with no luck. Any other advice to getting it off?

@KineticConsulting

Жыл бұрын

You should have let them know that it was out of spec man. I'd contact bw

Is that a True Barrel?

No date with the sharpie? 🤔

Trijicon recommends tightening the screws to12 inch pounds

@armyfazer1410

2 жыл бұрын

Thanks. I've been looking all over for that number.

Energizer lithium lasts longer

@KineticConsulting

5 жыл бұрын

Energizer batteries don't take shock very well and deform very easy. They are inconsistently sized which doesn't help with the battery connectivity. Duracells have a much better track record and qc.

shouldnt you degrease the rmr plate?

@KineticConsulting

5 жыл бұрын

You can, I don't. I like to keep a spot of protectant between the plate and slide. I like in a humid place though. So that's up to you.

Where did you get the battery retention plate?

@hadenblyat4849

Жыл бұрын

im not sure which one he is using in the video, but a quick google search and there are tons of manufactures that make them. Which one is the best ? im not sure but ive been using T rex arms plates for a while now and everything seems pretty good!

What length is the screws and where did you get them?

@KineticConsulting

4 жыл бұрын

You can get the correct length screws from Agencyarms.com

Screws are too long for my slide. How can I trim them?

@KineticConsulting

4 жыл бұрын

I don't trim them myself. I know there is a way but you have to make sure the threads aren't ruined. I prefer to purchase them cut already from Agency Arms

Do u have to sight it in again?

@KineticConsulting

5 жыл бұрын

Yes.

Hi what plate do I need to mount a rm06 on my zev z09 ?

@KineticConsulting

Жыл бұрын

Not sure. I don't use zev stuff. You may want to contact them to see

Do you have tape over the end of your X300?

@KineticConsulting

3 жыл бұрын

Yes. I put painters tape on the lense to keep it clean during day time training.

@cb7677

3 жыл бұрын

@@KineticConsulting Makes sense, I like that idea better than vaseline/catcrap some guys go with. Thanks!

Where’s home base for you?

@KineticConsulting

4 жыл бұрын

S. Florida

Why the fudge doesn't trijicon include a sealing plate with their rmr

@KineticConsulting

Жыл бұрын

Because it's not mandatory. I live in a wet place so I prefer having it

@Luke-id1cp

Жыл бұрын

@@KineticConsulting would you be comfortable with running your rmr with no plate in light rain

@KineticConsulting

Жыл бұрын

@@Luke-id1cp yeah, just not for multiple days

@Luke-id1cp

Жыл бұрын

@@KineticConsulting Alright brother I appreciate the reply

Tappy tap tap...

The wheeler torque wrench is cheap

my slide has has screw post.so no worry's

@mariannesisler2020

6 жыл бұрын

Jon Dufresne yes,Spartan

Hmmm, I would have thought there would be a specific torque for those screws

If ur optic can’t handle a little tapping than you got a sh*ty optic 🤣🤣🤣

A lot of wrong information 👎

I stopped watching this when he put the sticker on the battery

Dudes just use VC-3 not loctite.

It is bizarre to pay Trijicon $500 for an optic that doesn’t come with a crucial piece such as a sealing plate. Like wtf is that. I’ve never had to do that for any other red dot. Get real trijicon…First and last RMR that I will buy. Better last for life.

All that just to replace a battery!? It’s like the first gen apple mouse WTF LO Fucking L!!