It would be good to finish the job with setting oil height . And how you install the oil. Most important part man

Replaced the factory seals on a 2015 Evo 300 about a year ago after watching your video. Just serviced them yesterday, never would have tried it without your detailed video. Many thanks.

Legend ! Also if you dont want to buy a fork seal driver wrap duct tape around the fork tube till its around 4mm thick and use the use the tube to drive in the seal ✌🏻

need to do that to my bike aswell this winter :) thanks for a very good tutorial!

Very well explained top man just done mine saved £'sssss

This is fantastic, thank you!

thks for teach me !!!! very good tutorial bro!!

@sw-freeride

6 жыл бұрын

Jose Luis Rodríguez glad I can help. Thanks mate :-)

Nice, have done one video for maintenance on tech forks too.!

Thanks for the info

Great video!!! I have to change both seals in my evo 300 2013 and your video has detailed everything really good. Do know how much oil in milliliters is needed in each fork? I don’t have the tool to mesure the level. Thanks for the video!

how do you take apart the cartridge to properly clean it ? i did the same as you but it really needs to come apart for a proper cleaning before reassembly .

hello, how much oil goes into the return fork ?? the one without spring ?? the manual says 6cm from the top edge, but it doesn't say if the cartridge should be full ...

why back off the top clicker/adjuster screws?what does that do?. Also on my beta i just slide the seal on from the other end no nead for tape. Also like the other fella said how do you refill .

Heyy Enduro Boy UK, is 120mm on the spring side w/ or w/o the spring inside the leg ? Thanks a lot

Do you not need to bleed these forks ? If they are anything like tech forks you do.

Great effort hats off. But really really would love to know how you got the bottom bolt back in after filling it from the bottom lol. I’ve never seen or done that before and I do it for a living. Great video keep it up 👍

@sw-freeride

8 ай бұрын

Cheers mate but I don't have a clue as this was a few years ago now!

Put the top bush in before the tube ?

Ace video but I got seasick after 2 mins 😂😂

👏🏻👏🏻👏🏻

The fork seal driver has always pushed both the seal and bush in for me.

Hey i have Question...

Hi there,I can't get the bottom bolt out of the damper leg it just keeps spinning, so I can't get stanchion out.

@sw-freeride

3 жыл бұрын

Try an impact driver that may help

Thanks for the great and informative video. One question I have, at 13:00 when you talk about the seal orientation, is this correct? I'm currently attempting the same job with the same forks and make of seal. I thought the same as you however I also contacted the manufacturer to check and they said the side with the writing on should remain visible (so the non oil side). From your video I think you're doing it the other way? Does anyone have any experience with this? Which way is correct?

@sw-freeride

2 жыл бұрын

Hi thanks for the comment. As far as I know everything was correct. Although this vid was made a few years ago now! Usually the seal will go flat side down. The inner side will have a spring inset into a groove in the seal.

@user-dh6wj1jf2e

Жыл бұрын

I was wondering the same thing. My original seals are installed opposite of the way they are installed in the video

Hi...new to gasgas forks...they don't have a spring then !!???

@rikashaw4815

5 жыл бұрын

The opposite leg has the spring, this one has valve components for rebound damping

Ey I heard they are still bloody leaking Did you have a helmet cam for this one ?

@tomthumb891

3 жыл бұрын

Yep defo fucking things still leaked worn out !!

Good but made me giddy !

where did you buy the seal driver

@sw-freeride

5 жыл бұрын

www.dirtbikexpress.co.uk/bike_parts/motocross_suspension/motocross_suspension_accessories/drc_fork_seal_driver_universal_kit

This video is helpful, but the POV is making me seasick. Hopefully you can use a tripod next time ;)

Good vid but hard to watch because of the head cam

Sorry but why put the seal on the bottom of the stanchion, whilst saying be careful of the sharp edges? Why not put the seal on from the top? Surely if you change the bottom bush put that on first, grease or oil the stanchion and put it into the lower. Then slide the top bush down, with the cup and push into place with the seal driver. Then put the (oiled) seal on from the top and seat that with the fork driver. Never, ever use a metal screwdriver to lever up the fork wiper, one slip and you'll be amazed at the price of a new stanchion.

@IgyTheVan

3 жыл бұрын

Putting the oil seal on from the top - exactly what I am thinking.

@spongeyspongey5983

2 жыл бұрын

exactly why I just re-read this, couldn't see why it wouldn't go on the top?... no sharp edges?!.. that is my plan anyway..

I got dizzy couldn't watch...sorry.

You really are not sure of what you are doing and how to do it. Pull your valve stacks to clean and drain them properly and assemble your fork tubes before you install the seal; then you install the seal and stuff from the top. That way you do not have to tape the lower slider bushing grove, hence it is less likely to cut the seal installing it from the top. AND you do not pour the fork oil in through the bottom, assemble it completely then pour it in from the cap like you should.

@garydwall

Жыл бұрын

Vx do you have a video or info on exactly what to do that you wouldn't mind sharing?? Thanks