Hippie hope you and the family & the bros have a happy happy and a merry merry 💯 thanks for the kickass video’s dude !!!! I know it’s a lot of work !!! So from me and all the viewers THANK YOU 👊
@hippieschoppercorner
7 ай бұрын
Merry Christmas and thank you man
@MoeLarrycurly17 ай бұрын
I recently picked up quite the 75 FLH I'll be watching this video and many of your others for shovelhead info thank you so much
@hippieschoppercorner
7 ай бұрын
Thanks man. I just found your channel earlier this morning. I'll subscribe after work
@MoeLarrycurly1
7 ай бұрын
@@hippieschoppercorner 👍🎄✌️🎄
@twilightzone69177 ай бұрын
Stay real, stay safe
@sherrellferguson7 ай бұрын
Thi is where I plan on doing vids. gave you another subscriber.
@warrenp20227 ай бұрын
Hope you had a good Christmas ride. At the beginning of the video you spoke of different length screws for the rachet lid and that yours were all the same. The two long ones are behind the shifter, two deep holes. Dirt and crap collects in those two deep holes and makes it difficult to get the screws out. I have some foam that I stuffed in the holes to keep the crud out, then sealed that to keep out water/rust. I had the lid off mine a couple of weeks ago to adjust the shifting forks, it is still on the bench, so I went out to count. I have 9 short ones and the 2 long ones plus the breather. I should put it back in the bike but I've been lazy. You probably did some of that off camera. My box is running FX gears so the jockey shifting is first to the back and second, third and fourth forward, my understanding is that the FL units shift the opposite. I need some of your energy. ☺
@hippieschoppercorner
7 ай бұрын
I knew the 2 directly behind the lie should be longer but they were the same. It doesn't surprise me on this pos transmission lol
@randynewtonsr96597 ай бұрын
Merry Christmas Hippie, I wish all the best for you and yours and I’m looking forward to many more killer videos from you bro 🤙🏻🤙🏻
@hippieschoppercorner
7 ай бұрын
Merry Christmas man
@yruphuct27 ай бұрын
Great video. Sketchy all the time 😂cheers
@bruce18167 ай бұрын
Put the 26 on trans and 49 on wheel. It will keep rpm down at present day highway speeds. Besides, it will give you. outstanding gas mileage. The shift fork was probably pushed up against the gear and had the barrel in a bind. That's why the top didn't want to come off.
@hippieschoppercorner
7 ай бұрын
Kool, I'll try that ratio man. Merry Christmas
@toddk.58737 ай бұрын
It's gotta be the dowel pin holding you up. Try bringing it up staight as possible. Spray it down with some penetrating oil, let it soak. They can get a little oxidized.
@hippieschoppercorner
7 ай бұрын
10 4
@jerrybigrig7 ай бұрын
Ive got a long sawzall blade..ground off the teeth..ground off the mounting tab..ground off the front point..so when i get into a situation like this..its thinner than a screwdriver..wont marr up the gasket surfaces.. Good luck getting that one apart..
@BikerHenz7 ай бұрын
I’d say the fork adjustment is shit on it but hell I don’t know . Keep on keepin on man!
@Chevyv8man17 ай бұрын
Good video, I put a clamp on the back of the adjustment plate with a spacer between the plate and bench and clamp it down to your work bench. I have a suggestion for you on filming stuff like this. Instead of putting your camera behind you, put the tripod on the end of your bench by your door, so we can see what you're doing better. The way you have it we can't see very well plus your body is in the way. Not busting you but just trying to help you to have better videos. Thanks and I love watching videos like this. Later bro
@hippieschoppercorner
7 ай бұрын
Thanks man. I'll definitely remember that
@ridered73947 ай бұрын
Weather is crazy all over the place man, supposed to be 53 tomorrow here in Michigan, Merry Christmas everyone
@hippieschoppercorner
7 ай бұрын
Merry Christmas
@Lucky..B7 ай бұрын
Merry Christmas Bud
@hippieschoppercorner
7 ай бұрын
Same to you!
@kirkbickel68617 ай бұрын
Never saw you pull out the two long screws behind the shift drum
@hippieschoppercorner
7 ай бұрын
I forgot them lol that was the problem
@benderbender12337 ай бұрын
kick itz ass hip! 🤘
@hippieschoppercorner
7 ай бұрын
Lol I'm trying
@benderbender1233
7 ай бұрын
@@hippieschoppercorner ur getn it. 🤙
@yruphuct27 ай бұрын
Back for watch hours 😅🎉 cheers
@davids.41357 ай бұрын
Merry Christmas!!
@hippieschoppercorner
7 ай бұрын
Merry Christmas
@rustyshovel87717 ай бұрын
Merry Christmas Hippie…
@hippieschoppercorner
7 ай бұрын
Merry Xmas rusty
@sherrillferguson26687 ай бұрын
64 in Louisville today
@hippieschoppercorner
7 ай бұрын
Merry Christmas Shakey
@edZILLA647 ай бұрын
Merry Christmas. Im gonna get you a bigger Hammer for Christmas, to get that cover off. Lol. What if you try pulling up on it and spin it at same time, if thats possible. Good luck, i know you will figure it out.
@hippieschoppercorner
7 ай бұрын
It's kicking me Arse 🤣🤣🤣🤣 merry Christmas big Ed
@edZILLA64
7 ай бұрын
@@hippieschoppercorner you'll get it. Take a break , enjoy Christmas , then come back with a clear head. You don't need to pull that shifter off first, do you?
@repoRod7 ай бұрын
5
@mossycup69747 ай бұрын
Use a bigger hammer😜
@kirkbickel68617 ай бұрын
You are really schkey i am not but still like your channel
Пікірлер: 44
Thanks for watching
Hippie hope you and the family & the bros have a happy happy and a merry merry 💯 thanks for the kickass video’s dude !!!! I know it’s a lot of work !!! So from me and all the viewers THANK YOU 👊
@hippieschoppercorner
7 ай бұрын
Merry Christmas and thank you man
I recently picked up quite the 75 FLH I'll be watching this video and many of your others for shovelhead info thank you so much
@hippieschoppercorner
7 ай бұрын
Thanks man. I just found your channel earlier this morning. I'll subscribe after work
@MoeLarrycurly1
7 ай бұрын
@@hippieschoppercorner 👍🎄✌️🎄
Stay real, stay safe
Thi is where I plan on doing vids. gave you another subscriber.
Hope you had a good Christmas ride. At the beginning of the video you spoke of different length screws for the rachet lid and that yours were all the same. The two long ones are behind the shifter, two deep holes. Dirt and crap collects in those two deep holes and makes it difficult to get the screws out. I have some foam that I stuffed in the holes to keep the crud out, then sealed that to keep out water/rust. I had the lid off mine a couple of weeks ago to adjust the shifting forks, it is still on the bench, so I went out to count. I have 9 short ones and the 2 long ones plus the breather. I should put it back in the bike but I've been lazy. You probably did some of that off camera. My box is running FX gears so the jockey shifting is first to the back and second, third and fourth forward, my understanding is that the FL units shift the opposite. I need some of your energy. ☺
@hippieschoppercorner
7 ай бұрын
I knew the 2 directly behind the lie should be longer but they were the same. It doesn't surprise me on this pos transmission lol
Merry Christmas Hippie, I wish all the best for you and yours and I’m looking forward to many more killer videos from you bro 🤙🏻🤙🏻
@hippieschoppercorner
7 ай бұрын
Merry Christmas man
Great video. Sketchy all the time 😂cheers
Put the 26 on trans and 49 on wheel. It will keep rpm down at present day highway speeds. Besides, it will give you. outstanding gas mileage. The shift fork was probably pushed up against the gear and had the barrel in a bind. That's why the top didn't want to come off.
@hippieschoppercorner
7 ай бұрын
Kool, I'll try that ratio man. Merry Christmas
It's gotta be the dowel pin holding you up. Try bringing it up staight as possible. Spray it down with some penetrating oil, let it soak. They can get a little oxidized.
@hippieschoppercorner
7 ай бұрын
10 4
Ive got a long sawzall blade..ground off the teeth..ground off the mounting tab..ground off the front point..so when i get into a situation like this..its thinner than a screwdriver..wont marr up the gasket surfaces.. Good luck getting that one apart..
I’d say the fork adjustment is shit on it but hell I don’t know . Keep on keepin on man!
Good video, I put a clamp on the back of the adjustment plate with a spacer between the plate and bench and clamp it down to your work bench. I have a suggestion for you on filming stuff like this. Instead of putting your camera behind you, put the tripod on the end of your bench by your door, so we can see what you're doing better. The way you have it we can't see very well plus your body is in the way. Not busting you but just trying to help you to have better videos. Thanks and I love watching videos like this. Later bro
@hippieschoppercorner
7 ай бұрын
Thanks man. I'll definitely remember that
Weather is crazy all over the place man, supposed to be 53 tomorrow here in Michigan, Merry Christmas everyone
@hippieschoppercorner
7 ай бұрын
Merry Christmas
Merry Christmas Bud
@hippieschoppercorner
7 ай бұрын
Same to you!
Never saw you pull out the two long screws behind the shift drum
@hippieschoppercorner
7 ай бұрын
I forgot them lol that was the problem
kick itz ass hip! 🤘
@hippieschoppercorner
7 ай бұрын
Lol I'm trying
@benderbender1233
7 ай бұрын
@@hippieschoppercorner ur getn it. 🤙
Back for watch hours 😅🎉 cheers
Merry Christmas!!
@hippieschoppercorner
7 ай бұрын
Merry Christmas
Merry Christmas Hippie…
@hippieschoppercorner
7 ай бұрын
Merry Xmas rusty
64 in Louisville today
@hippieschoppercorner
7 ай бұрын
Merry Christmas Shakey
Merry Christmas. Im gonna get you a bigger Hammer for Christmas, to get that cover off. Lol. What if you try pulling up on it and spin it at same time, if thats possible. Good luck, i know you will figure it out.
@hippieschoppercorner
7 ай бұрын
It's kicking me Arse 🤣🤣🤣🤣 merry Christmas big Ed
@edZILLA64
7 ай бұрын
@@hippieschoppercorner you'll get it. Take a break , enjoy Christmas , then come back with a clear head. You don't need to pull that shifter off first, do you?
5
Use a bigger hammer😜
You are really schkey i am not but still like your channel