thank you so much

@newtecpro

Жыл бұрын

thnx bro

Quick question. What happens if i try to read 105volts with it.... i have a power supply that can deliver little more over 100 and i dont want to burn the module. Will it burn if i exceed the 100v? or it wont show anything more than that 100 stucked in there.

@newtecpro

11 ай бұрын

Yes, most likely higher than 100 volts will cause damage. Never use more than 100 volts

Thanks

@newtecpro

7 ай бұрын

Welcome my frind

thnks

@newtecpro

Жыл бұрын

TNx u

I just bought two of those meters, I connected them the same as you, but, although it shows the use of voltage and the circuit works without problems, the meter does not measure the current, it is simply at 0, both meters behave the same.

@newtecpro

Жыл бұрын

Most likely, you have not connected the wires correctly. Please check the wiring method carefully Also, the electrical device must be turned on and consume electricity.

@hugodavid2244

Жыл бұрын

@@newtecpro The problem was that they ripped me off, it doesn't even have the metal bar that is used as a resistor to measure current.

@georgioszotos5519

11 ай бұрын

@@hugodavid2244 Yours must be V2.0 Without a wire shunt. But on the other side of the A connector there must be an SMD shunt resistor R010. And is brighter as normal SMD resistors. So is my. It works but i haven't used for more than 2 Ampere.

When i connect shunt ampre readind going to zero, why?

@newtecpro

10 ай бұрын

You may have connected incorrectly. The shunt must be installed in parallel

@dinamics2

10 ай бұрын

@@newtecpro yes its parallel connected.

What is cost of this meter

@newtecpro

Жыл бұрын

Its price in online stores is approximately US $3.73

20 HP 3 phase motor ke liye chahie

@newtecpro

Жыл бұрын

ok

The reality is that the old (analog) instruments could be used as long as no overcurrent was introduced by mistake, so they were good for many, many years. Today's (digital) instruments don't last more than a year or two, and they break down if they happen to be near the high voltage of an old TV. Some of them are already defective, so today's technology is not user friendly, but hazardous waste friendly.

@__-hh3gt

Жыл бұрын

You are correct. Thanks

سلام خسته نباشید ممنون مهندس یک توضیح کامل میخواستم دررابطه باطریقه فعال کردن آمپر من یک رسیورمینی دارم که دوازده ولت دوآمپره که ازطریق ماژول افزاینده وپاوربانک میخوام به رسیور برق برسونم اندازه گیری ولتاژوروکه بلدم ولی چطور آمپرو وصل کنم یاانتقال بدم به رسیور ومطمئن باشم که دوآمپر برق مصرف میکنه منظورم اینه دوسیم روبکجای رسیور وصل کنم ممنونم اگه یکم راهنمایی بکنید متشکرم موفق وپیروز باشید❤❤❤

@newtecpro

Жыл бұрын

The amperage is nothing to worry about. In the technology of switching power sources, the electronic device consumes as many amps as needed. If your receiver uses 2 amps, it will only receive 2 amps.

@mohammadpour.61

Жыл бұрын

​@@newtecpro thanks❤❤❤