Thank you! So many of these videos are less clear or don't apply to my situation. Thanks again.

ขอบคุณครับ ดูแล้วเข้าใจง่ายดี

ufff eres la solucion que andaba buscando

The one I have is giving wrong ammeter readings and the trim pot at the back is doing nothing. Is it faulty? I have the same connections.

Hello. I got the same meter on ebay. I connected everything like the video for a 24v power wheel ride on car. After about 10 mins of riding. The shunt got really hot. I touch it and it was very hot can not hold on or will get burn. Is it supposed to get this hot? I'm worried it will damage the power wheel car or catch on fire.

does your digital Volt/Amp meter has an internal shunt in it's pcb board? I have two digital meters, one has an internal shunt and the other dont. Which one did you use? Thanks.

Done it works in bike battery charging and discharging function at a same time its shows reading in negative

What happens if we (mistakenly) reverse the direction of the Ammeter connections on the shunt (I.e.we let the current flow in the opposite direction of the ammeter)?

So we need a two batt?what if i use in motorcycle?

very well sir thanQ. but in the 2nd diagram with charger charging current it showing.for the change just replace the charger with the bulb load,without changing any other connections ,is the meter shows the discharging current? have u tried.if u tried tell m e sir.because it saves my time.

Do you know if we mast use Fuse?If yes how many amperes?

If used to measure the current of the inverter Which circuit must be connected?

Can i Kill the power to save Energy and still let flow electricity through the wires

To use an external shunt, do I need to remove the small shunt installed on the meter?

@metrointernetkafe

2 жыл бұрын

You dont have to.

How it shoes accurate amp through the shunt?? ... I have tried this connecting method... Shows an amp drop through the shunt.. Tried calibrating through the trimmer... Still in accurate..

@chitibusu

3 жыл бұрын

same here, very inaccurate on measuring current, at 5 Amps measured on a very good multi-meter, this device show me 6.2 A....China stuff

I have Got This (100V - 10A) Meter and i have found that 2 Adapters was written 9V and Coming 17V :D and another 13.3V and coming 6.5V. Now About Meter: You Can Use Meter Only With AC Adaptor Or Battery - To Turn on. Use Minimum 3V Maximum 12V and Maximum 1.5A. Use thin red (+) and thin black (-). thick Red - is changing Pulses thin Yellow - also changing Pulses thick Black - also changing Pulses 1) Volt measures thin Yellow and thick Black 2) Volt measures thin Yellow and thick Red 3) Amps measures thick Red and thick Black

Bro ye metter alternator charging ke ampere batata hai kya

nice 💯✔

👍👍👍👍👍

electrical diagram please нарисуйте пожалуйста схему ! 6:04

Bang klo power of meternya saya colokin ke aki 12 v gpp kn? Jdi cukup pke 1 aki, gx prlu baterai lg

Music name??????????????

Nice video SIR ask ko Lang poh Kung ok Lang ba na kahit wlang load eh may reading ung Amper na 0.70???

Ye volt amp meter kaha milega . Shunt ke sath hoga kya

Could you provide a schematic for the connections? I have received two of these meters with zero schematic or connection diagram. Thnx

Podrias dejar el diagrama

Lovely

apakah harus pakai 2 power suplai gan?

48 volt m sir us hai ki nhi

Where do i get this matter

How to use it in solar panel

Help white SMPS CT .amplifier??

Title: How to Connect an Ammeter

Battery changing input dayagram

Why we use shunt and what is advantage of shunt ?

@bobcarter6143

4 жыл бұрын

The Ammeter is really just another Voltmeter and simply measures the voltage drop across a resistor - that resistor needs to be both big to cope with the 50 Amps and relatively low resistance so as not to drop too much voltage (upsetting the load) and not get too hot. The shunt is just a big resistor.

Can we use one battery for this..

@TheDrewker

4 жыл бұрын

Depends on your meter and how much current you're trying to measure, but yeah you probably can. The meter I have can use the same power (minimum 3.5V) as long as i'm measuring under 10A. But I might go a little over 10A so it needs separate power. I'm using it for an ATX power supply conversion, so I'm powering the meter with the +5VSB rail and using it to measure the +12V rail. My meter is just like this one, 50A with the external shunt. You might find this helpful: hamguyparts.com/files/Download/Chinese%20DVA.pdf

How calculate 49.9amp dc that meter sir It's showing 0.00 r Real is 49.99

Detailed video, i bought same meter, but no instruction, i will try ur way, thanks

Bang aki di kasih step down bisa buat lampu LED 2 Amper ta

@aldiband9171

4 жыл бұрын

Bahan"nya buat itu apa aja bang tolong sebutkan 1 per 1 bang

Sir this meter link parchge

where is diagram 2?

@letsdoitthailand

4 жыл бұрын

facebook.com/HearKaiEngineer/photos/a.140971979960205/369445647112836/?type=3&theater

@planet.photos

4 жыл бұрын

Why just not show the diagrams, not sure.. anyway these diagram links actually did the job for me (even though I have one with thick blue wire - that stands in stead of the thick red in those diagrams...oh and one thick red , instead of the yellow one.. - just to know if you have similar): goo.gl/eZvq2c goo.gl/lHKSN3 One more thing - ammeter needs a good load over 250 mA to start showing anything at all.. at least on the device I have. so don't be tricked that it doesn't work if you test with small load LED - it does. just load it more

Ngomong lebih baik dari musik.

where is ""wire diagram 2" ???????????????????

Where is 50a??

Definitely disliked. Stupid pandomima music

@satishparmar1301

4 жыл бұрын

model/part no. and link to order this

Thumbs-Down because you are using the same stupid images from the Chinese sellers and because you are not explaining anything and because you are playing loud annoying music and NO, I DONT WANT TO DO IT IN THAILAND !!!

Worst Making the meter