I like the way you did this video talk is cheap action speaks louder than words!!!

Thanks for sharing! I just did this job, and didn't know about the 6mm hex bolt on the top of the shock. I took the entire heat shield thing out of the way to do this job. On the bright side, it wasn't a complete waste of time, over the years all sorts of leaves and junk built up in the driver side wiper area where there's nothing to stop it. Hit it with a shop vac, sucked up a ton of ants, now it's good to go.

Nice video straight-to-the-point. No BS. Thank you very much

@jlsetnuper

2 жыл бұрын

Thanks for watching..

Great video! Simple and straight to the point!

@jlsetnuper

2 жыл бұрын

Thanks for watching

Very good clear video … also inclusion of wrench sizes really helpful to quicken the job .. many thanks🙏

@jlsetnuper

Жыл бұрын

Thank you..

Thanks for the video, it really helps me alot.

@jlsetnuper

3 жыл бұрын

you're welcome

Great job!!! I am doing a pair tomorrow 😊

@jlsetnuper

5 ай бұрын

Thanks for watching

Great video, very much appreciated

@jlsetnuper

2 ай бұрын

Thank you

Thank you very much, I saved a lot of money 💰💰

@jlsetnuper

2 жыл бұрын

thanks for watching...glad it helps

Great video man. Thank you

@jlsetnuper

Жыл бұрын

thanks for watching..

Thanks for the excellent content.🙂

@jlsetnuper

3 ай бұрын

thanks for viewing

I have subscribed to the channel. This Yaris hatchback is said to be super durable.

@jlsetnuper

8 ай бұрын

Thank you

Got it. Hard as hell. Thin rubber. I was pulling metal

Thanks for the video

@jlsetnuper

3 жыл бұрын

No problem!

Hi, my fronts struts are changed but the mechanic fixed a bushing under the cap on the top of the car metal to avoid space between the car metal and the cap when the car is on the ground. Is it advisable, or there mist be a space between the car metal and the cap when the car is on the ground? Thanks

Thanks for this

@jlsetnuper

10 ай бұрын

You're welcome

How tight is the top strut nut? It looked like it needed couple more turns

thank you!

@jlsetnuper

3 жыл бұрын

Youre welcome..thanks for viewing

Torque spec? Never heard of it

is there a trick to popping that dust cap off

Thank you for Nm

@jlsetnuper

3 ай бұрын

Thanks for watching

Hi my shocks absorber are changed. Thanks for your help. When the car is on the ground, can you tell me if the cup of the top are on the car metal or if a little space? Thanks.

@jlsetnuper

2 жыл бұрын

There is a gap between the car frame and the cap when the car on ground.

@krisursule6230

2 жыл бұрын

@@jlsetnuper I buy a Mpaco and i compared the original and the new. The originale come into the big hole above the shock absorbers and the new not come completly in to the hole....

@krisursule6230

2 жыл бұрын

The new, is the same like you have got. You can check the KYB video. A good part : for exemple: SNR KB669.21. I Think is better . I will test it and after car on the ground.

Struggling here with the top bolt . What a stupid design . The cap was missing on it so it’s rusted so bad that the hex is no longer hex . Tried to vice grip the cylinder and still slips . Going to be a fun one.

I noticed the new rubber mount has a different pattern on it. Were you aware of it? I believe the metal part where the rubber mount meets the car frame is not match then? Any idea?

@jlsetnuper

3 жыл бұрын

it has different grove from the old one, but they fit perfectly on the car frame and the most important is the bearing set properly that rubber support..

@CloudGarageAsia

3 жыл бұрын

@@jlsetnuper At 5:04 I noticed the car frame has markings, are those grooves as well? If not, the two types of rubber mount can be really used interchangeably then.

@jlsetnuper

3 жыл бұрын

@@CloudGarageAsia the car frame has no groves, its only a dirt marks from the old support rubber..its like a sphere that cut in half..you see it at 4:03 from the top..

Where did you put the little washer that comes in the same bag as the new top nut??? I can't find this anywhere if it should go on top where the bolt sticks through or if it goes in between the steel mount ring and the nut that has the coil spring torqued down. Monroe doesn't include where to put it in the manual... I am asking because this brand new strut STILL has a gap when I lower the car and I can't close it by tightening, so I am afraid I just pulled a newbie and put the washer in wrong. Any help is most appreciated!

@jlsetnuper

3 жыл бұрын

there is no washer when I removed the top nut, and that shock absorber is still original..the top nut and plate is floating before I replace the strut..check my other video (kzread.info/dash/bejne/pKSsy6uGYKvLg7A.html) before I replace the strut, there is a gap between the car frame and the top plate..

@dlouis1830

3 жыл бұрын

@@jlsetnuper Thank you so much for getting back, that’s exactly the issue is that I have new struts in there and it’s still floating… I might have a solution right now actually I am tighten the top night and I’m going to put the car on the wheels instead of jacking it up to see if that puts it closer and not float

@dlouis1830

3 жыл бұрын

@@jlsetnuper Do you think floating is just a symptom of a bad strut or is it a problem in and of itself. Like if I have new struts that are floating, possibly because of a workmanship issue, can I just leave it?

@jlsetnuper

3 жыл бұрын

@@dlouis1830 just leave it like that..its normal to be floating so that the top nut and plate are free to move when turning..

@dlouis1830

3 жыл бұрын

@@jlsetnuper you’re a lifesaver thank you so much cheers

Did you replace the shock absorber and the spring? Ive seen some replace only thr shock absorber amd need special machine to compress the spring and disassemble..

@jlsetnuper

2 жыл бұрын

yes, I've replaced the spring and used the old shock absorber. check this video link kzread.info/dash/bejne/eJWCp5R7pbS5m5M.html

@leolealuianderson5291

2 жыл бұрын

@@jlsetnuper very nice... So is it a strut or shock absorber mine is 2008 yaris. And im seeing some call it a strut and others a shock absorber. Just wanna make sure i get right part. The dealer told me i need the shock absorber and shock absorber mount replaced. But i can only find strut for 2008 yaris

@TanManFixes

Жыл бұрын

@@leolealuianderson5291 it is a strut and coil spring assembly. shocks are for the rear only. For the fronts, you want the part that comes with the entire strut/coil/mount

Hello, the 17 Offset wrench its an 30° offset ? (min 3:21)

@jlsetnuper

2 жыл бұрын

In the video I used a 17mm deep offset ring spanner..

do you need an alignment after doing this?

@jlsetnuper

4 ай бұрын

yes you need an alignment after the replacement

What parts did you buy? Looking for 1-2 inches lower.

@darkrulier

2 жыл бұрын

You're going to need lowering springs for that. For this car, cheap and ok quality go with Tein.

Would you recommend the socket set you used and where can you get them from.

@jlsetnuper

2 жыл бұрын

thanks for watching..You can buy any socket set from 9mm to 30mm. And better to find an impact socket set of any brand.

@hardworker8030

2 жыл бұрын

@@jlsetnuper Where did you buy the socket set you used as I want one that just comes with sockets. I did look in halfords but they come with things I don't need.

@jlsetnuper

2 жыл бұрын

@@hardworker8030 I buy it from amazon..the socket set I used is SEALEY Model no. AK5634M

@hardworker8030

2 жыл бұрын

@@jlsetnuper Thank you

you are very lucky that none of the bolts broke. even with the penetrating oil i broke 2 bolts. Otherwise, good video

@jlsetnuper

3 жыл бұрын

thank you..

@matronix1977

2 жыл бұрын

How did you deal with the broken bolt ? Go to the garage of fix it yourself ?

Where did you get the 6mm Allen wrench bit at

@jlsetnuper

2 жыл бұрын

I bought the allen wrench bit set from a store ( LIDL).

@davidvalens3337

2 жыл бұрын

@@jlsetnuper how many nuts did you have to remove to do this job?

@jlsetnuper

2 жыл бұрын

@@davidvalens3337 one on the top and 4 at the bottom..

Thanks. Is it à parkside?

@jlsetnuper

3 жыл бұрын

Thanks for viewing..yes its a parkside from LIDL store.

@krisursule6230

3 жыл бұрын

@@jlsetnuper Ok if it's good working. i will test it.

What mileage did you change at?

@jlsetnuper

3 жыл бұрын

the car has 66500 miles..

you need an alignment...