That was the best how to video I've seen. Straight to the point, all details thoroughly explained, excellent video quality, editing and camera work, clear audio and just the right amount of information to explain what and why. Thanks for doing what you do so well.

@timkevwitch862

2 жыл бұрын

Exactly! I could give 2 shit how you're week is going or how this is for my hillbilly cousin that can't read! Just get to the point and cut the dam camera when you're removing 20 bolts I really don't want to hear your gossip! I wondered if I was the only one that was irritated with that shit lol.

@TheBenefactorZ

Жыл бұрын

Seriously

@dennissuding4452

Ай бұрын

I was just gonna pull the drain plug and fill up what came out! Now I'm preparing for this whole process. I'll use a floor pump jack, not a car lift. I'll video tape it.

Terrific instructions. Most noble genre on KZread fr.

Lugs are 21mm and the fill port is 24mm. Otherwise your assessment is fairly accurate and concise. I just do drain and fills on mine.

Dude I've been searching high and low for such a video for my 2010 Venza. THANK YOU!!!!

@thejunkyardmechanicwilliam7848

6 ай бұрын

The best video on this so far

Perfect video which explains everything you need to know about a partial Transmission fluid change, gives important information like tightening specs for bolts. Thank you for your professional presentation! 😃

Appreciate your help! You were quick and to the point in describing what and how to do it. Thanks a million!!

@reyesarriaga5306

2 жыл бұрын

You’re not showing how to check the level to the right temperature

Best video on ATF change in 6 speed for Lexus Rx 350 etc!... thanks a lot!!!

Best Sienna transmission fluid / filter service video on the Tube, hands down... thank you very much for making this!

What a thorough and comprehensive video on this topic. Thank you so much for posting this, I will be performing this soon on mine!

Very nice job showing the filter replacement in detail.

best video I have seen for this type of service. Thanks again for posting this.

Great video, straight to the point. Unlike others where they talk and talk until they sound like an overflowing toilet and then talk some more.

Excellent work, i like your style of work

Thank you for the quick, to-the-point video.

Excellent Video.....MASTER MECHANIC.....HIGHLY SKILLED CRAFTSMAN!!!!!!

wow!!! very concise to the point video.... well done and thank you!! Just bought a 11 Lexus es350 and will being doing this soon. Again thanks!!!!

Great and very specific video!!!. I did this same on a Highlander 3 years ago. In addition I disconnected the lines from the transmission and and blew all the oil that was on the radiator cooler and on the standalone cooler.

Excellent video my man

Keep up the great work. You are a hero for the DIY mechanic like me. I didn't go the extra mile to replace the filter as you did since most other videos I watched before this didn't do it. Hoping to keep my 2011 Sienna running for another 8yrs. Only has 130K miles on it now.

Bro thank you for being specific 🙏 it helped alot and stuff thanks man your a real one!

Thank you for breaking it down and explaining the torque

Beautiful video. Torque specs and everything done right and clean. Liked and subbed. Just one question, no thread sealer needed here?

Thanks for explaining this in good detail!

I found a "Low Profile socket set" that had a tiny 10mm at O'Reileys that did the job perfect to get to the hard to get one under the frame. It worked perfect.

@carlovanrijk4039

3 ай бұрын

bbhoustontx, I used a tiny 10mm with a flexible elbow to get to that hard-to-reach bolt…worked like a charm!

You are Professional bro Keep posting

Outstanding video!

well do sir ....straight to the point

Very helpful and educating video, thankyou for sharing

Great video !!!! Very informative.

Very good video. Very helpful. Thank you.👍

So I’ve done this job watching these nice how to videos in my particular case I live in the rust belt 3 of those 10s that hold the pan on broke and there’s one stubborn 10 mil bolt that I couldn’t get to with any sockets or wrenches had to unbolt the transmission mount 3 17 mil bolts it is and jacked up the transmission managed to get a wrench in there I did the transmission flush at 112 thousand miles it’s first service still runs strong fluid was black 2012 Toyota Camry

excellent video, thanks

EXCELLENT video. 👏🏽👏🏽👏🏽

Excellent video. Thank you

@ramonmorales9646

5 ай бұрын

I changed my in the dealer and now mi transmission don't work its suck 2013 Sienna with 83k😢

great video! Question: so i did it today, i drained 2.25 qts cold, i refilled to 2.5, heated it up to 110 F. but when i did the final drain, i got 1L back, should I be concerened? I put the drain back just before the dribble was apparent, it was a veyr thin slowing stream. Also, boht tires on teh ground, but the driver side was jacked up a few inches as well, please let me know? btw, the shifts were alot softer.

clean job

awesome video thank you!

Great Video, tried to follow this procedure on my 2007 Toyota Harrier (same as RX350) it's a AWD. The problem is that there is no Fill plug (or dip stick) at least not in the location shown, I wonder if there is a fill pull at all, but if so where is it ? thanks

very,very profesional and experience🙂😊

Good video

Tnx alot sir for the video..bit how many quarts in total will i put on my camry 2013?tnx

Got one that catches in reverse at 2k rpm when its warmed up ive got in in the temp specs mentioned but when i pull the bottom plug fluid is consistently pissing out....could it be that over filled?

Nice video thank you

Did you have to buy a new o -ring or did it come pre attached to the new filter?

beautiful

Nice vid

I have a 2009 Aurion. This Winter im noticing a delay in drive when cold. It goes into drive fine. But shifting up from crawling pace it's indecisive in the first couple of gears

Manual says there is one bolt that needs to be pre coated with a Toyota adhesive. Any thoughts? Thanks

Excellent

Question: I have a 2012 Lexus RX350 with a CVT trans Car has 181,000 miles, dealer told me never open up trans fluid and never touch it. I wanted to replace Trans Filter, and new Toyota WS trans fluid. Is this a wise thing to do at 181,000 miles ? What can you recommend please?? Thank You

So around how many quarts did it end up with once it was filled and the excess fluid was drained out from the overfill port? 😊

Thank you

Thanks!!

Let's say I had to also replace the valve body. Any tutorial or info about that?

Bruh, that was tits on. WAAAYYYY better of a video than anything I've watched. Very professional and quick, to the point. THANK YOU!

How many miles do these transmissions last?

Question: After new fluid in (3 Qts.), Do you check final level (dribble out), with engine running?, sounds like it. Sorry if I missed something in Video.

@MasterJacks

3 жыл бұрын

Yes, you want to put the three quarts in, then start it and check/adjust with engine running. Put plug back in, get the fluid warmed up a little, then check again.

This the same trans in the 2011 camry le 2.5 auto 6 speed?

I have a toyota camry 2011 4-cylinder 2.5L. is this the same process for the 4 cylinder? you only listed v6 in your video.

when should i change the oil and filter of my camry?

i have a stuck TCC solenoid, will the oil change resolve the issue?

I like your details I like and Subscribe

I have a 2007 toyota camry, how many quarters of oils I will need to purchase to due the change oil from transmission ? Please

Only thing I would have done different is let the oil out first through the drain plug before removing the pan but this is excellent thanks for sharing this vid. I have a lexus ES 350 it's got the exact same engine and should be all the same.

@deasttn

28 күн бұрын

Me, I would have cracked open the fill plug first

thanks

Not a criticism but more of a question..why not use the drain plug to empty the transmission first and use the dipstick tube to fill it? Wouldn't that be less work?

There were blue thread lockers on my 10mm pan bolts. One of the bolts is a PIA, no room for a 1/4" 10mm socket to get in, not like this video which had a little more room. This morning the grinder will be my friend to shorten that socket.

How much oil is needed to refill the automatic gearbox?

Tremendous video both visually and verbally. Just wondering when a new filter ought to be installed on a Camry if the trans fluid is changed every 60,000 miles.Thanks

@peterrudy9207

Жыл бұрын

I say a filter filters out the bad stuff , how to when it has reached it's limit ? . And a new one at anytime , couldn't be harmful

This would work for a 2015 Toyota Rav 4 xle 2wd right?

You make it look so easy but my potential problem are the transmission pan screws potentially snapping off due to salt over the years. My RX has 200K miles on it and some of those screws would be a nightmare if they break. Scared!

Any opinions on whether to use an aftermarket filter like, beck/arnley , or do you use oem transmission filter from dealer?

@carlovanrijk4039

3 ай бұрын

4mins4peace, I’m sure you could use that beck/arnley if it complies to OEM specs. I went ahead and got the OEM from the dealer…may have been a little bit more, but I’m trying to keep my Venza with original Toyota parts.

Are the torque specs the same for a 2017 camry 4 cylinder?

Does Toyota Avensis T27 year 2010 2.2D-Cat has the same Transmission?

Tnx alot for the video sir...do u need to warm up the engine b4 u will drain the transmission?and do u need to turn on the engine when u fill the transmission oil?thank you

@MasterJacks

2 жыл бұрын

It drains better when it's warm. Add a couple quarts after the filter change before starting the engine. You then need to start the engine to check and adjust the fluid level.

@stebaibisdakmtb

2 жыл бұрын

@@MasterJacks copy sir...coz i have 2013 camry se model,but usually how many quarts of transmission oil will i put?

Just changed filter and fluid on 2012 camry. there is one tranny 10mm bolt that was a bear to get out. I ground down a 3/8" 10mm socket to be no longer than 5/8". It did the job, but a 1/4" socket would have been better. took forever. I just read another post below saying O'Reillys sells a low profile socket set. that would have been great.

@kimchee94112

11 ай бұрын

The video shows more room to get at that 10mm bolt. There is no room on mine even with a 1/4" 10mm socket, not even with a swivel. One guy said he got it out with a 10mm wrench, seriously my wrench had no room to turn. Don't want to jack up the engine, I will sacrifices a 1/4" 10mm socket to get it in this morning. Mine is 2014 V6 Camry with no dipstick, going by temperature. The filter looks different, need to notice if the three bolts are different lengths, on some Toyotas they are. Total PIA!

I have aa 2010 avalon bought it from a lady with 228000 miles for 3000 bucks..I did oil n other services but can't do the tyranny fluid because I just don't kno when lady it was replaced..should I still change it or leave it in.. ? I saw a sticker saying return for service at 201850 but don't just don't know..

A 2014 dodge caravan has a transmission dip stick port with no stock dip stick from above and you can use your oil dipstick with the proper low and high scribed fluid levels on it as your transmission dip stick too. Can this be done too with most sienna models too? I'm not to thrilled about catching all the fluid to know the exact amount to replace after draining the pan too. great video 👍

@anggaros1

Жыл бұрын

You cannot with this type of trans as you can see the fill hole is on the side.

Cuantos cuartos de aceite lleva la transmisión

Hey where is there transmission speed sensor is located 2014 seinna limited awd. I have p0793 code

How many quarts comes out with the filter change?

Great video! Does anyone happen to know approximately how long it would take for a professional mechanic to do this job? I have a 2013 Camry LE 4 cylinder non-hybrid. My mechanic says both of his manuals call for like 2.8-3 hours and he told me that seems longer than what the job should actually take, but he isn't sure until he takes a look. If so, it would make a ~$350 job more like $480-500!

what kind of digital torque wrench do you have? I want to buy the same kind. Thanks

@MasterJacks

3 жыл бұрын

I actually just use a manual clicker. I like the Tekton 1/4" 10-150 in lb wrench.

Where did you get that pump to put over the bucket. I need one of those.

@MasterJacks

2 жыл бұрын

It's called a bucket pump. You can get them on Amazon.

Is this the same on a toyota mark x ?

When draining out the excess fluid when warmed up what did u mean when u said "adjust the fluid if nothing is coming out?"

@MasterJacks

Жыл бұрын

If nothing is coming out, the fluid level is too low. You would need to add fluid until you're getting a light trickle. If it's dumping out a lot of fluid, you would need to let it drain until you get the same light trickle.

that like.. How much tranmission-oil sienna2012?

Hello beautiful people, does anyone of you know by doing the procedure in the video how many liters of oil the 2008 Camry v6 transmission takes, thank you very much

Please show how to replace ATF filter on 2017 & 2013 Lexus RX 350 F-Sport model, they are 8 speed transmission with side pan , not drop down pan as you showed. Thank you!

@mvnga3362

22 күн бұрын

you need a 12mmm allen wrench for the drain plug bottom of the transmission

Nice video, i am using 4 jack stands, how to ensure the leveling ? shall we use some level Guage, any suggestion ?

@venessankurumeh1549

Жыл бұрын

Maybe roll down all windows and rest a leveled wooden plank across each seat row on top of the window frames so you can put a bubble level tool and check in the middle and at each side

@anggaros1

Жыл бұрын

@@venessankurumeh1549 wooden plank? are you building a house or something? He can just buy a leveling gauge and stick it to the bottom of the pan.

@JW-mz1fp

2 ай бұрын

@@anggaros1 yes thank you.

Your Amazon link looks like the wrong filter? from the one you removed, I need to do a 2017 sienna soon.

@MasterJacks

Жыл бұрын

Nice catch, thank you! I've updated the link.

Is this the same as U760E?

how many miles on this car, fluid looks black

Is there any harm in bypassing the old transmission flush part in the cooler and just do the rest of the video? 😂How many ounces of old transmission fluid would be in the cooler?

How much will Toyota dealers charge for this service? Approximately

Where are you located I would take my Avalon 2018 to you to do it? Do I need to drop pan and change filter, I got 47K or can I just replace the fluid?

@MasterJacks

2 жыл бұрын

It depends on the fluid condition. If it isn't terrible (dark and burnt smelling), then you could probably do a drain and fill for now and plan on the filter in another approx 30k.

While the pans off , why not fill it with liquid / or ATF up to the overflow tube then measure - ballpark idea of what the pan holds before overflowing

@MasterJacks

Жыл бұрын

That would work as a starting point for the initial fluid check, however, transmission fluid has to be checked with the engine running in order to be accurate. When the engine is running, the fluid is circulating throughout the transmission and cooler, which gives a different reading than when it is static.

While checking that final level through the drain bolt did u have the car engine running or turned off?

@MasterJacks

2 жыл бұрын

It needs to be running

@brownstv9423

Жыл бұрын

@@MasterJacks Could you also just measure what came out and put the same back in?

@MasterJacks

Жыл бұрын

That could work, but checking it is really the best way to ensure proper level.

can you over screw that red straw thingy, or does it eventually bottom out when you screw it in? I'm afraid i'll screw it too far and it'll end up in the pan, and i don't want to have to drop the pan to retrieve it.

@MasterJacks

Жыл бұрын

Good question. No, it bottoms out to provide an accurate fluid level in the pan.

@deasttn

Жыл бұрын

@MasterJacks thanks. It just seemed like I was screwing n screwing n I was afraid of screwing it right into the pan. Your video was helpful. I just changed my fluid. Most challenging part was getting all 4 wheels off the ground and leveling the car 😀

Do you have to pull the tire to fill it back up? Can you fill from the top side in the engine bay instead?

@richieadhikari9146

Жыл бұрын

Yes you can, I did mine without removing the wheel.

@kimchee94112

11 ай бұрын

Sure, but no big deal to remove the tire for easy access since all four wheels already jacked up.