this is priceless ..this is the next best thing to having done it before

@DillonHFM

7 ай бұрын

glad to help, subscribe and follow along, I'm going through the whole machine

@spark23ca

7 ай бұрын

@@DillonHFM oh i am ..especially the gears they are the same as my franklin ... the frnaklin is alot like your skid king it hinges in both ways in the middle and doesn't have walking beams in the front ..some skid kings came with a swede or franklin type winch ..i see you have a gearomatic on yours....do you sell parts like planetary gear sets?

@DillonHFM

7 ай бұрын

I can get parts for most things, I am a dealer for aftermarket parts. I do have a swede winch, I will have to check but I think it is a 30. It's off a skid king if you are looking for one. @@spark23ca

@spark23ca

6 ай бұрын

@@DillonHFM i might be ..it would ensure i don't need one if i had a spare lol ..i'm mostly looking for the bronze bushings and 3 gears and little washer/bearings ..i think i would be easier putting them on then having one bust ..1 was busted when i bought it and i built it over from spare parts i got with the skidder..i don't know how long it ran like that but it sure did make a mess of the holes for the bronze bushings ...i'll email ya sometime if you like ..i seen an email somewhere on your page thanks for responding

@DillonHFM

6 ай бұрын

@@spark23ca I can get parts breakdowns if you need and from there get a quote for you. my email is dowen10200@gmail.com

Same as other guy great 👍 job love the break down! Thanks for sharing 🤠

@DillonHFM

Жыл бұрын

Thanks for watching!

I enjoyed your video way back in 1983 I got my first skidder a case it had rockwell pr75 diff the man I got it from said the only thing to watch for was the pinion nut would loosen and it would i got tired of tightening it and looked up the torque specs it was a lot so I put it to the spec said no wonder it got loose all the time. Well I took it for a test drive on the dirt road made it a 1/4 mile heard a loud noise stopped and shut it down smelled smoke it was on fire and the drive shaft hanging down two times with the fire extinguisher to get it out the pinion shaft was red hot wrung into. Well it took 7 months to get the parts it was an odd ball ratio had to be made at rockwell. Putting it all back together reading through the manual it said plac proper number of shims on pinion shaft to space bearings gess what I didn’t have any spacers and so I knew right away why it got hot. The man should have told me he didn’t put the spacers in I would have never torque it down. The lessons we learn in life can be painful. Thanks for your video

@DillonHFM

Жыл бұрын

always good to check the diagrams, but hard to predict what people have screwed up before you got there

You should turn the pion put the ring gire under l

@DillonHFM

3 жыл бұрын

I will give it a try on the next one

Great job sir! I also have limited spin differentials. My are Clark. The whole axle (differrential and side reductor) is 1 to 26 ratio. How much teeth do your diff have?

@DillonHFM

3 жыл бұрын

It is a 5 by 39

Any info where parts can be purchased for planetary ends?

@DillonHFM

4 ай бұрын

I an a dealer for aftermarket parts and can get all of that stuff. otherwise check online or heavy equipment shops. I can get schematics with part numbers and prices if you want, My email is on the channel page

Hi! My friend have an old skidder with Rockwell axles. Where do you get parts for them?

@DillonHFM

3 жыл бұрын

Bearings can be ordered from the number on each bearing. Other than that, you can look on google and try heavy truck suppliers. The center section in the same as a truck axle, it just has planetary gears on the ends. There are used parts available as well

@fyst4413

3 жыл бұрын

@@DillonHFM thanks 👍

Where do you learn to do this

@DillonHFM

6 ай бұрын

I worked in a hydraulics/ machine shop for a bit, otherwise this is just how my brain works. I take things apart, look at them, and fix them. A good use of google usually helps to find parts breakdowns, or for this I found specs for it in a machine manual that I have. If you can find a parts breakdown, you can see exactly how everything is supposed to fit together, and on older stuff, sometimes figure out if anything was left out last time through, and a manual is always good for specifics such as torque or lash.

@RamYRN

6 ай бұрын

Where can the manual be purchased

@DillonHFM

6 ай бұрын

On older stuff like this, ebay is a decent place to look, I got one from a facebook forum for the 360 as well.@@RamYRN