Your decision to do this full time is completely validated. Your ability to convey your expertise and thought processes in a diligent and understandable way, should not be under-estimated! Well done...

That “data? Rewind tape” message brings back so many bad memories from 40 years ago! You could easily spend an hour trying to load Elite.

@andygozzo72

3 ай бұрын

at least an electron or bbc can 'recover' from tape load errors by trying a block again, a spectrum would stop with R tape loading error and you'd have to rewind the whole tape and start again, electrons and bbcs split loading into small blocks..

@TheChloeRed

3 ай бұрын

@@andygozzo72 Yeap, and there's 2 errors, Data? and Block?. Normal rule of thumb was if you got a block error, you would rewind a little, adjust the volume up, and play. If you got a data error, you'd do the same but adjust the volume down!

@mikespangler98

3 ай бұрын

Cassettes were so slow. 😒

@andygozzo72

3 ай бұрын

@@mikespangler98 yep, but thats all you had for many systems, unless they make a disk interface,, and you could afford it.....many cost more than the computer itself

@AdamHougham

3 ай бұрын

This, combined with a dodgy power supply plug in later years made using my electron quite stressful in later years! An age to get a game loaded and then a small knock and the system would reset!

I was watching this on my TV. I took the time to log in to my account so I could comment: the outtake was absolutely worth waiting for.

If the attempted repair was done in the 80s, access to an oscilloscope would have been limited. Access to schematics might have been available, but as you point out, the diode isn't in the schematics. Even access to a multimeter with diode testing would have been somewhat pricey. Not to mention, the years of experience you have with troubleshooting 8-bit computers would have been confined to electrical engineers. So parts cannon was the only method we had unless we knew someone in university.

@wilfredpayne433

3 ай бұрын

Can't you remove the diode and use a battery or power supply to flow current through it in both directions to run a light bulb and verify functionality? Potentially using larger or smaller bulbs to somewhat load the part? Thank You For Your Time And Effort! I Hope You Are Having A Great Day Or Night!

@paul_boddie

3 ай бұрын

The diode (D8) appears in the circuit diagram published in the Acorn Electron Advanced User Guide which corresponds to the issue 6 board. The diagram in the Acorn Electron Service Manual corresponds to earlier boards. For what it's worth, I did a KiCad version of the circuit that also includes this diode.

@johnhaller5851

3 ай бұрын

Oscilloscopes weren't hard to find in the 1980s, but the ones available to the hobbyist had limited bandwidth. Heathkit sold an oscilloscope kit, and I bought a used one. It was damaged in a flood in the 1990s, so I don't have it any more, but it definitely worked, at least up to being able to look at TV signals and lock onto the NTSC pedestal. New, modern oscilloscopes at the time were very expensive, but not required for debugging this problem. I was a poor college student, but was able to afford that oscilloscope.

@Stoney3K

3 ай бұрын

Yeah, it's really mesmerizing to think that we have really access to super advanced instruments today -- digital storage oscilloscopes, logic analyzers and super cheap FPGAs. Stuff that cost a fortune back in the day when these computers were developed.

You have to look back in awe and appreciate what 6-11 year olds in the UK were being exposed to in the 80s via BBC Basic and hexadecimal checksums. It really is a sight to behold. And to reinforce this, there was a "game" on the BBC Micro called Granny's Garden. Most student's passed it off as a game, but actually this "game" was a kinda like "The Last Starfighter" in that students who SOLVED the dragon section, were actually solving LOGIC GATES. This to me is incredible looking back at what the BBC and the Government were doing.

@bradallen8909

3 ай бұрын

Students. Why can’t anyone use apostrophes correctly anymore?

@techtinkerin

3 ай бұрын

Great comment so true!!

@baronvonschnellenstein2811

3 ай бұрын

@darkstatehk: Yes, that dragon puzzle was quite the sting in the tail!

@baronvonschnellenstein2811

3 ай бұрын

@@bradallen8909 At least the OP is using punctuation and it is broadly being used correctly!

@ProdigalPorcupine

3 ай бұрын

Granny's Garden, haha! "Do you want to help the King and Queen?" "You DO want to help the King and Queen!" 😂

Remember my Acorn Electron cassette lead having three jacks; input, output and control to stop start the tape.

@emolatur

3 ай бұрын

At 13:00 he mentions the extra pins in the din connector used for switching the tape motor.

@TinySpongey

3 ай бұрын

I remember many cassette players had a 2.5mm jack for pause. Doesn't look like that panasonic one has one though.

@rossthompson1635

3 ай бұрын

Yes, output for saving programs to tape - did lots of that, still have the tapes but sadly not the Electron :-(

The first of those op-amp circuits is simply an amplifier to increase the signal strength from the cassette player as much as possible. The second stage is a low-pass filter to get rid of any frequencies above the data frequencies, and the final op-amp stage is a clamping circuit to limit the amplitude of the signal.

@wilfredpayne433

3 ай бұрын

I've never actually learned what opto couplers, op amps, and how different transistors, mosfets are used or can be used for... and it's because I can easily look up what type of behavior I should see from good parts and have not had to learn the actual operation of them... which I need to do... so when I don't have access to my pocket computer I can actually diagnose properly...I have learned everything I know by jumping in head first and figuring it out on the go... thank you for your time and effort! I Hope You Are Having A Great Day Or Night!

@gfiandy

3 ай бұрын

Further to BFLmouse's reply, I expect the diode was added in a later revision because that opamp is on +/- 5V rails and it is not unusual to get large turn on transients on an opamp. With a 10v from positive to negative you might occasionally get a greater then 5V transient the other side of the cap and certainly a lot bigger than the 1.2V it seems to have been designed for. This will be passed onto the ULA via the cap at turn on. This with repeated exposure it probably damaged the input. The diode would clip that to 0.7 ish volts, however it looks like they didn't put any resistance in line so that diode is pulling the output of the opamps current each transient. That transient will happen with every positive change in the signal through the diode. That is probably quite a lot of current on each pulse hence eventually the diode fails. Two diodes would have prevented the turn on transients without overloading the diodes as it would be about the same voltage as the transistor diodes are clipping the feedback loop too. Or they could have put a small resistor in series to limit the current through the one diode. The current circuit relies on the output resistance of the opamp and the ESR of the cap plus the trace resistance and inductance to limit the current.

@nickwallette6201

3 ай бұрын

@@gfiandy Looks to me like a clamping diode, to set the DC bias of the signal coming out of the cap. Not necessarily to catch over-/under-shoot.

Yes, I had an Acorn Electron many years ago. Spending ages and ages waiting for games to not load from tapes. Happy memories. 🙂

Nice find with that diode! Here’s my quick circuit analysis, ‘cuz I like analog and audio electronics: Second opamp looks like a Sallen-Key two-pole low-pass filter, cutoff at 4.1 kHz. Third opamp is a symmetrical “soft” clipper, to make the signal very square, over a wide range of input amplitudes (as you stated!). They’re being tricky in the clipper, wiring transistors as diodes. I’m guessing it was easier and cheaper to throw on two more BC239 transistors than to source small-signal diodes just for this part of the circuit.

@adriansdigitalbasement

3 ай бұрын

Awesome -- yeah it's a bit magical to me, but I at least get the general gist of what it's supposed to be doing just from previous experience.

@Drew-Dastardly

3 ай бұрын

That weird transistor arrangement is very common in the input protection section of many multi-meters. I think it was actually patented by Fluke decades ago, I'm sure Dave Jones has a video explaining it. It is some kind of Zener clamp.

@Bob-1802

3 ай бұрын

Yet they added a 1N4148 in a later revision instead of using another BC239.

@PileOfEmptyTapes

3 ай бұрын

Using a diode-connected transistor gives a more ideal diode characteristic. Not sure why exactly that would matter in our limiter circuit though. It's more important in other applications like current mirrors. The transistor solution would be more expensive even today.

@MatthiasWelwarsky

3 ай бұрын

@@PileOfEmptyTapes The transistors prevent saturation of the OpAmp output. OpAmps used as comparators are prone to that effect. Recovery time from saturated state is not neglegible and will impact the slew rate and thus the frequency response.

I admire your repair abilities! Congrats on narrowing down the issue to 1 simple component and fixing this machine! That little outtake at the end was fun! :D

The BBC loads tape programs in blocks. The counter is the block count. If any block gets miss read you can wind back just that block and try again rather than re-start from the start. The DIN connector also supports motor control so the computer can stop the tape between programs.

@Drew-Dastardly

3 ай бұрын

Yes, the BBC tape format was far superior to any other. Most of them would have a single header block with the name and loading address, and then a constant stream. BBC had a small header on every block with a CRC. This is all the counting from 01...05, etc. BUT you could rewind the tape a few blocks if the CRC failed. Also it allowed C120 tapes to be packed with games on both sides. Total genius.

@deavo74

3 ай бұрын

“Dara Rewind Tape” I seem to remember. *edit I’ve just got to that point lol, I wasn’t far off.

@retrozmachine1189

3 ай бұрын

The TRS-80 Model I and III tape format was similar. It was record based with the name having a particular record ID etc. For a 'system' (ie machine code) program each program record was up to 256 bytes and had its own checksum as well as a discrete start address for that block so it was possible to directly write to the screen RAM during a normal program load. Someone could write a tape that included a few bytes directed to the screen to show a fairly time accurate counter of how long to go until the program load was completed. The record ID for the last in the stream was different again. The only lacking for the standard TRS-80 loader was no ability to stop, rewind and try again. If it failed at the last record, rewind to the beginning and try again. Being able to do a retry of a failed record like the BBC does is a nice idea.

@aCivilServant

3 ай бұрын

In addition, each block is 256 bytes, so it was simple for the Acorn engineers to transfer the blocks to make each one a sector on a disc system if installed. Basically the same reading and writing format in terms of the OS, but on different media.

Couple tips. First, azimuth and cleaning of the cassette deck. Bad azimuth causes higher frequency tones to blur together. Easy to set if you listen to some music, adjust the screw until it sounds most crisp (most high-frequency details audible). Next, crank that volume! You'll get more dropouts if the volume is too low at the "barely detectable" edge of the signal. Hey, fun watch none the less!

First comment! Yay, my old BBC Master 128 is seeing some more use! 👌 All the best from Cambridge UK 🇬🇧

@TimGladding

4 ай бұрын

2nd, from a former resident of Cambridge, UK 🇬🇧

@ToNanOrNotToNull

4 ай бұрын

Third - most of my family are in Cambridgeshire

I was a teenager running a small shop for one of the UK distributors for Acorn back when the Electron was released. It was very disappointing having been a BBC user for a while to see how much of a poor relation this was. The slow speed was an issue obviously but the thing that broke a lot of games was the lack of Mode 7 graphics. A lot of games etc. used this for in-game text because of its low memory requirement. A lot of BBC Micro software *will* run quite happily though, albeit slowly, but there was enough incompatibility between the 2 machines to make it frustrating and hit sales figures. I think if they'd made it as a BBC with ports removed but still running at full speed it's impact on the market would have been much greater over here. As it was, it was a mere shadow of the BBC Micro.

@wembleyford

3 ай бұрын

I love the Acorn line - but you've had to felt embarrassed for anyone who's been brought a copy of Commando if they'd ever seen the C64 version.

@paul_boddie

3 ай бұрын

@@wembleyford That port of Commando was just lazy, easy money on the part of Elite, very much in the vein of the games industry at the time, with the whole concocted phenomenon of teenagers buying sports cars, Imagine Software, Ocean Software, and so on. All facilitated by the tame/corrupt reviewers of the day exhorting the readership to "go and buy this game immediately" (or equivalent) regardless of whether it was any good. See page 12 of Electron User, June 1986 for the evidence in this case. In fact, regardless of the original programmer's efforts, the publisher was so lazy that the title screen of the game shows the name of the game on two successive character lines. This is the hallmark of mode 7 double-height text shown on the Electron's mode 6 screen. Which means that someone got the BBC Micro version and did the bare minimum to "port" it to the Electron, which may have been nothing at all! Adrian practically demonstrated this by showing the Beeb version which is effectively the same. I suppose it shows how compatible the Electron was with the Beeb, though.

@cmdrgreyareauk7642

3 ай бұрын

To make it worse, if I’m remembering correctly the Electron shipped a year late due to problems manufacturing that massive ULA.

Good job! As for shotgun troubleshooting... if you've got a fat supply of every part, it's a really fast way to get stuff running. In fact, that's the DoD system of aircraft maintenance: replace every box that might be wrong to get the plane running, sending all of the suspect boxes bask to supply. Then supply sends those suspect boxes to repair centers to check out, where most run their test programs fine and only a few need to be actually fixed. Since boxes are filled with cards, you can recursively apply the shotgun approach ;)

@bugdrvr

3 ай бұрын

It can be a problem if you get the parts cannon out and end up installing a new part incorrectly, bridged a solder joint or something like that. Now you have a new problem and likely still have the original as well. Swapping boards or modules is easier and much less prone to cause a new problem but shotgunning at the component level is a great way to make a door stop.

Watching you put the cassette down on top of the cassette player speaker reminded me of the computer reseller where I worked in the early 1990s and the office person religiously backed up her computer to DC2120 tapes. She stacked the tapes on top of a clock radio on her desk once they were written and "verified". The only time that the backups were needed, many of them were too corrupted to restore sufficient data and about a months work of data entry had to be recreated and manually entered.

@kaitlyn__L

3 ай бұрын

That was a plot point in _Halt and Catch Fire,_ the clean-room BIOS programmer had left a stack of disks on top of a big speaker and they had to redo all the code they couldn’t reconstruct.

Ah the good old hexadecimal counter of tape loading on the Acorn machines.

Different ring 🎉❤

Old timer tip: check for the little pad thing under the tape that pushes the tape against the reader head. Sometimes it would sag a little, causing the tape to not make good contact with the head. If you remove it and fold it so that the pad is a little higher, everything works wonderfully again. Regards from Argentina!

taught myself to juggle waiting for tape loads on the BBC :)

That Panasonic tape recorder brings me memories... My dad had one just like it. Exactly the same model.

Adrian, yep Searching then the header which tells you the title, [if not the one you want fast fwd, and look for another header. The Acorn TapeFilingSystem is great. The numbers you see are block numbers in hex, if it miss reads a block, rewind a bit, clean head et-al, and try again, yep it will pick up from where it couldn't read the block. Side note when I had an Electron, a friend gave me Aviator for the BBC B, (I thought why not, give it a try) it worked, but very slowly. The Elc is the machine I learned 6502 on which led me on to a career in being a software dev! Well done!

@johnh10000

3 ай бұрын

Page is the top of memory, where your basic program starts. you could change page up by say 128 bytes then you have 128 bytes for user defined graphics vdu 23,ch,b0,b1..b7

Love the way you track down and diagnose problems. Excellent forensic work. Thank you.

Damn those game cassette tapes brings back some memories. I remember there used to be so many of them it was like a plague as they were really easy to copy, and everyone had them. Now you'd be lucky to find any surviving original copies. As tapes are not known for their durability, especially after 30+ Years.

Really enjoyed this one! I love when it comes down to a simple fix, and your ability to work through the board and find it is always inspring!

Came for the repair, remained for the singing at the end. :) Good job. I know nothing about these British micros, but this was a really enjoyable, methodical repair.

Well done tracking that down! I enjoyed the whole CSI of this this episode.

Great video. You can't beat the anticipation and joy (when it works) from tape loading 😅

This was so fun to watch. I only ever witnessed cassette storage at a friends house, and by the time I had my own 8 bit machine floppies were available. You're a hero for bringing these machines back to life. Thank you!

...well done sir! ...and thank goodness you didnt see Commando in colour..... its horrendous!

Brings back good memories of my Acorn Atom, my first real computer! Loved the repair methodology!

Congratulations Adrian for this success and the teaching in showing your repair with great humor. I have this type of cassette recorder and use it to load programs onto my vintage computers.

Hey, thanks for sharing your hobbies. It's inspiring.

Thanks for the followup, appreciate. :)

I used to have an Electron back in the 80s. The ULA used to overheat, so I always had the lid unscrewed to allow me to lift the lid to dab a bit of water on the ULA heatsink. Not really the recommended method of keeping electronics cool, but it worked! You using a lupe to read the diode's number is something I have to do now too. I remember the days when I used to be able to read components with my naked eyes in dim light!

I watched this like a movie) Thank you Adrian!

I really like to watch you troubleshooting computers 🖥️ And the best part of the video is when you find the problem and machine starts to work.😊

Excellent professional fault finding Adrian. Well done!

Such nice work with this troubleshooting. I always love watching the detective-like logical step by step narrowing down of the culprits until you get to the conclusion and seeing that "aha moment" is great. Keep up the great work it's like watching a detective show sometimes!

Looking sharp Adrian! 👌 Keep up with the good work! 👏

I really enjoyed the electron videos, as this machine is part of my fondest childhood memories! Thanks!

That was FUN. Thanks for bringing back a task I did so many years ago. But most of my repairs where without a schematic. Had to trace out the area to be worked on. Find a tape drive and cut into the motor feed and use the relay.

Best repair video yet!

Adrian I'm watching your channel since the beginning. I love your troubleshooting skills, you start at the beginning and follow the way until the fault shows up. This diode is the best example. Thanks for your videos, don't stop making such content. Love it. Have a nice time and take care. Best wishes from Germany, Robert

Another awesome video, I have the earlier version of the Elk that you have, it's really cool to see you holding all the same computers that I have here, including the ZX Spectrum 48k!

You've fixed WAY more computers than you've played Commando. Great job!

Congrats on 200K subscribers! Excellent Channels 🙂

Hey Adrian! Just want to thank you, all the knowlege you share through your vídeos are helping me to ressurrect an eletronic organ (a johannus prestige 10)from 1997!!!! It’s my church’s organ gifted from another church( it came all the way from germany to here, Brazil in 2000) it runs a Motorola 68008 as its processor and 128k of ram! I will post another update when the new parts for the board arrive!! And again, thank you so much my friend!! I am following your channel now for almost 5 years and your content are aways amazing to see!!!

Loved the outtake. Totally worth watching all the way to the end.\

Nice basic diagnostic search for the failing element. (a shorted/defective diode) I enjoy watching your videos. 👍

I just wanted to thank you for all of your videos. You inspired me to attempt a repair (power supply re-cap) of my BBC Micro. I haven't held a soldering iron in over 30 years, but I bit the bullet, bought a new soldering iron and the capacitors needed and gave it a try. And now I have a working BBC Micro! I probably wouldn't have even tried had it not been for your enthusiasm for this stuff. Thank you.

@nickk6109

3 ай бұрын

It has got me wondering if my dad still has his A300 (+ARM3 +4MB upgrade) in the loft. I think he still has his Sinclair Z88. I got rid of my RiscPC (StrongARM710+486+VRAM) a long time ago. Could have been a classic. In fact he may still have the Electron with Plus 1 (cartridge). I have memories of playing the Electron Plus1 Starship Command in a BBC Master.. Smoother and the high score game play is super fast :D

Great work. Always so informative and entertaining at the same time.

I love the debugging of the audio input. I always wondered how that was done. Analog signal to digital - just massively overdrive it, and cut off the peaks! So darn simple!

What a fun little problem! Well done!

You don't want or need the asterisk there. The Electron and BBC tape formats are identical. The problem you're having here is that you're looking at the Issue 4 schematic and you have an Issue 6 board- there's an Issue 6 schematic on the stardot forum.

That was plain awesome troubleshooting.

That Panasonic tape deck brings back memories from my childhood. I was rocking Licensed to Ill on it back in 86

Very satisfying to see this repair. A shorted diode!

Oh the memories ! My high school had a room full of the BBC's, and my neighbour had an Electron that I used to go next door and use nearly every day :) My first purchase was the Amstrad CPC-464 with tape drive - often games took 20 - 40 minutes to load, and then crashed !!!

Brings back memories of loading and saving programs on my old Ti99a.

Congrats on 200K subscribers !!

The transistors are there to clip inside the feedback loop. So with low amplitude on the feedback loop, they will make no difference, as you saw.

DeOxit solves everything, wife upset you missed your anniversary? Give her a spray of DeOxit and you're golden

Great diagnostics, very interesting stuff

Brilliant fix, well done !

Adrian, I know you're always evaluating your content, and I want to make sure that when you said, "This is probably like watching paint dry..." you were, happily, dead wrong! This speaks ill of those who DO watch paint dry, and doesn't account for the fascination I felt as I watched the first-ever realtime loading of software from a cassette tape. To me? That's riveting, coherent content--that I love. Big thumbs up, sir. Jonathan in Seattle

Fantastic troubleshooting!

tape programs brings back a flood of great memories !!

Came for the video, stayed for the outtake. In all seriousness, great video demonstrating the importance of taking your time when troubleshooting; throwing parts at the symptoms without knowing the problem is always more expensive and not a definitive way to solve one.

Love these old computers. I had a Vic 20, CBM 64, Spectrum , Atari 400, Amiga 500, Amiga 1200 - I wish I still had all of them rather than Binning them 😞...well done you

Excellent methodical trouble shooting. Every time you cut from the schematic I expected to see a shot of surface mount stuff under a microscope, not the glorious gigantic old school components. Fun stuff, congrats!

Well done Adrian!

Loved it! I was making all the same troubleshooting decisions as you were - felt good! 🙂Glad it worked out for you!

When I first saw this I thought I knew exactly what the issue was but it was hardware related for you. On the Ti994A we had we used the the generation before that Panasonic tape player (RQ-309DS a touch heavier due to more steel in it). It had a tone control and my brother and I found that you could not have the tone set all the way to low or high but the Ti preferred it in the middle for loading software.

I have an old CoCo that need restoration. Having a PC that could load programs from cassette is a goal of mine. Thanks for this video.

those 2 transistors connected like that make them work as diodes, with good hard 0.6v ish drop, and in the feedback loop like that, male that op amp a 'squarer' and amplitude limiter

Just seen your video, we use to have a Electron when growing up. We also had Acorn Electron Advanced User Guide, it had more upto date schematic, which does show the D8/D9 diodes on the cassette in/out from the ULA.

Nice bit of diagnostics, I had my fingers crossed that it wouldn’t turn out to be the ULA so great the machine was fixable. Glad you sussed out that you just needed to use empty quotes which was standard for pretty much any machine to load the first program found on tape.

Nice repair job nice too see, greetings from the Netherlands

This brings back memories…. My first computer was the electron, I remember for loading games the volume level was very important. somewhere between 3/4 and full depending on game then the dreaded syntax error….. happy days

This took me back to the 70's when I purchased a kit to build the UK101 single board computer. I rushed it home and by about 8 pm I had it up and running, using the TV which I had prised away from my wife and children - with some effort. But it would not store programs. I had all the components installed correctly, but it was not until someone suggested that I check the capacitor used in the 90/150 c/s (Hz) generator that generated the tones recorded onto tape that my error came to light. Instead of using a capacitor with something like a +/- 5% tolerance (may have been a 0.1 uF) I had used one of the decoupling type capacitors which had massive + tolerances. I swapped to the correct type and away it went! I had a lot of fun with that machine, but loading and storing programs was so time consuming!

Nice work, really glad your ULA wasn't fried those things are getting rare... I think I read somewhere that the BBC Master tape input uses the same, or very similar conditioning circuitry so you might've been able to follow the signal through the Master and compare it with the Elk. However not needed as you got your man in the end 😊

@crunchyfrog555

3 ай бұрын

It is very similar and you can load BBC games on an Electron. Sometimes they don't work, sometimes they work more slowly, as there's obvious differences between them. But the tape structure is the same.

33:40 I had a C64 that loaded nothing from tape. I then noticed that the tape read contact in the cassette port was shorted to ground. I traced it as far as I could, noticed that the copper leads to one CIA but also branches elsewhere. I experimentally cut the branch trace, leaving the connection between tape port and CIA intact, and VOILA, loading from tape worked. Everything was fine as far as I could tell, until I acquired a 1541. Trying to access the disk crashed the computer immediately, so I thought it might be related to the tape issue. I took out the schematics, and found out that yes, the serial port shares the tape read line, plus, every signal line in the serial port section goes through a diode snubber network. These are a set of 8 diodes, wired in series pairs in reverse between +5V and ground, the signals passing through the center junctions. Once again experimentally, I snipped the related diode on the ground side, and now the serial port works too. I have left it as is, maybe fix properly later. EDIT: obviously I bridged the previously cut trace, otherwise it would not work.

Great video. Some Electron tapes will load on a BBC B or Master. I loaded up the electron version of Chuckie egg on BBC B. Also to load a tape you can also use the shortened command of CH.""

Great fix!

what an amazing repair, I did enjoy the troubleshooting! That poor thing keeps on giving! Let's hope this is the last time with this electron! :)

I played Commando on my C64 back in the 80s for hours on end. This video really shows how much faster the C64 is compared to the BBC Micro.

Well in defense of the old ways. Who had all the fancy diagnostics equipment in their shed in the 80's or 90's?

That was a really interesting one, Adrian! In your situation, where the inherited machine arrived with partially de-soldered ULA, suspicion immediately falls to that device. Very glad to see that in the final analysis, it was a readily replaceable discrete component that had failed. - P.S.: Welcome to loading from cassette tape hell! You "missed out" on this growing up with an Apple //c with integral FDD. My impression is that the majority of folk in the USA who had 8bit machines tended to have FDD drives. -> In the rest of the world, most of us at least started out with cassette as the data storage medium on 8bit machines and the FDDs usually cost as much or more than the computer itself did!

Amazing. Rather than replacing big chips, just find a dead diode that's not even on the schematics... Congrats on saving this piece of history

Loading games from cassette tape... the struggle was real. We were so spoiled here in the U.S. Floppy disk drives weren't too uncommon for many "well to do" families. Even then, my Commodore 64 friends had to wait longer, if they didn't have the Fast Load cartridge. Ahh... good times.

Great job troubleshooting.

Good job! Commando is probably one of the worst game choices for testing an Electron as its a typical cash grab port of its time which runs like mud and makes the computer look bad... Can I suggest... Snapper, Arcadians, Starship Command or even the Electron version of Elite.

The Acorn Electron was my first computer and it started my 25 year career in IT. My favourite games were Snapper and Arcadians. I hope you do a follow-up video where you get it hooked up with colour output and try out some more games! Thanks very much.

how was I not subscribed to you? I suppose the algorithm gets some points for sending your vids to my home page enough I thought I was.

Great work. Just a quick heads up; the C64 tape version of Commando has a fantastic piece of SID music playing during loading. Not my favourite C64 tape loading music, that goes to the Ocean Loaders(the 3rd version takes it for me, but they're all pretty great), but still a nice piece.

The price difference between the master and electron seems to be represented well in how well the game runs on each system. We are used to this sort of thing with PC gaming but I was a little surprised there would be that much of a difference here on 8 bit Micros.

4:23 I had a little 'ohh NO' moment, when you pressed the play button and the record button got engaged too. 😱 weird concept of having to press the same button for play and record.

BTW if you want to capture colour it's fairly easy to build a RGB scart lead for the BBC family of machines. Just a few resistors in the back of the scart plug to bring the levels down.

It is not necessarily due to the cassette that nothing is loaded or becomes faulty. You have not considered one thing: The sound head track should be set with a sound head adjustment. The track fidelity can change over time. I have always done this by ear. The brighter the sound, the more accurate the track. There are small adjusting screws where the tone head is screwed on.