Thank you so much Sir. Where is the O-ring? Is it in the back of the torch or in socket of the plasma?

Good discoveries. Will try this on my sickly 42

Thanks for sharing, very helpful. For connection issues, you could try some contact cleaner (EX: WD-40 Specialist Electrical Contact Cleaner Spray)

@tothwelding8329

4 жыл бұрын

Already have tried contact cleaner. Even tried die electric grease. Its a bad design and doesn't get good cotact

Hi, Can you show a video on how you went about setting up controller or building all components on how to make and run table. Great couple videos you have. They are in simple and show that a big fancy table is not needed to get cuts like you do. Thanks

@tothwelding8329

3 жыл бұрын

There are too many controllers or different ways to run the table. There are also alot of videos and info out there already that show this and how I built my table. I will be making my plasma table from 5ftx4ft to 8ftx5ft using my old table parts to build it bigger and I might do a video of that. I recently put a candcnc mp3500 control package on with bigger stepper motors and a scribe. Also did away with the td52.

@michaelmisiolek3054

3 жыл бұрын

@@tothwelding8329 Thanks for the reply. Really like your videos. You speak on my level. So many videos go so fast you can not even see what they are doing. Your table is not the best looking, But wow it shows that you do not need these fancy tables. Your cuts are amazing they look better that 20k table. Is that the plasma cutter ? everyone seems to use Hyper Therm . Would be great to see more videos and if you build a bigger table. Thanks

Amigo como conectaste tu thermal dynamics a tu CNC, yo rengo conectado el divisor de voltaje, el stop y start, pero el cnc no camina, no se donde conectarlo, podras ayudarme

Como hacerle la.conexión trifasica 380 a la máquina la tengo con alimentación monofasica 220 ayuda

buenas tardes tengo un cutmaster 52 el cual al momento de activar la antorcha el arco golpea la pieza y no se genera ningun arco continuo

@DonitasZoe

2 ай бұрын

Hola me pasa totalmete igual me da chispa pero no continua

I have a cutmaster 42 .... never got the thing to work got a new gun for it ( seems like the air actuator does not work )

What torch height controller are you using?

@tothwelding8329

3 жыл бұрын

Proma

@juansalto9019

3 жыл бұрын

@@tothwelding8329 also I have a problem with my torch starting late. So my cnc starts to move before my torch comes on. I already have the max delay start in my program but is not enough. You happen to know a fix?

@tothwelding8329

3 жыл бұрын

I don't have any problem at all with nothing starting late. I would just buy one that has support that way they can tell you how to run the machine. My machine is home made and doesn't work like anyone else's.

How can I wire my CM? My machine doesn't have the CNC interface.

@petersc1000

26 күн бұрын

You need to buy the interface board. May be in your manual

I own a CM52,, It arcs but does not cut

Thank you for the video. Looking at buying this model.

@nelsonsantos770

3 жыл бұрын

NO, don't buy thermal dynamics! It sucks! Buy everlast or other model instead!

Anyone had issue with plasma torch pilot arc then cut off? What,why,how to fix issue?

@tothwelding8329

5 жыл бұрын

If the arc is going out it probably has something to do with your start cartridge. Its spring loaded

Could you help me with mycutter

If you don't get an arc check this.... Part of the cup hides in a slot in the handle. In that slot is a little switch that senses the edge of the cup. If this switch doesn't sense the cup ----- no arc --- red light at !

I have a cutmaster 42. There is no air getting to the handle. I jumped the pressure switch, nothing. I checked voltage to the solenoid that opens and provides air to the handle. Should have 24volts dc to the solenoid, I have nothing. Any experience with this problem? I've downloaded the service manual, so I'll go through the input output voltage checks. Thought you may have run across this. Thank you for your time.

@tothwelding8329

4 жыл бұрын

Im not familiar with that machine

I was gonna say it needed to be refilled with toilet paper. But if you blew your owering out you might want paper towels.

@jonvallembois4205

Жыл бұрын

Oring

Did you have to install the cnc interface board to hook up to torch height controller. I have the CM52 and was able to trigger switch to cut without THC but I want to install a proma thc and was wondering how it’s wired on yours.

@tothwelding8329

5 жыл бұрын

No i didn't use a cnc interface board for the plasma machine. I have the proma thc mounted right to the side of my Plasma machine case with a 4x2 wet location electrical box. Ran the high voltage to the proma and all the high voltage wires are all still in the case. The up,down, arc ok are run through inputs on my board and im running LinuxCNC

@carrgrienier7726

5 жыл бұрын

So you get raw voltage from inside the machine on board? Positive which clamp and negative from electrode?

@tothwelding8329

5 жыл бұрын

Raw voltage from lead inside the machine. The ground lead is actually the positive and the torch is negative. They are attached to board with a nut. Youll see when you take machine apart.

@carrgrienier7726

5 жыл бұрын

Right sorry...I was able to find the trigger switch inside when I set it up with Grbl and it worked but need a thc and saw a bunch of options online couldn’t find anything for this machine.

@carrgrienier7726

5 жыл бұрын

And will be using Linuxcnc also

I have now lost 8 minutes of my life that i can never get back, and i feel violated, dumber, I award you no points for your effort, and God have mercy on your soul!!!!

So what's the solution?

@tothwelding8329

3 жыл бұрын

Throw it in the scrap pile and put a hypertherm in its place. It's what I did.

Please

Get a Hypertherm. Thermal Dynamics is JUNK. Ive been fighting this machine at work for a year.

@tothwelding8329

2 жыл бұрын

Got rid of that piece of junk 4yrs ago. Have an powermax 85