The WORST Axle Bearing I've EVER SEEN - How To REPLACE Classic VW Swingaxle Axle Bearing
Автокөліктер мен көлік құралдары
Taylor replaces a bad axle bearing on the mystery beetle.
Fritz Tools Bearing Puller -
www.thesamba.com/vw/classifie...
Follow @wickedwerks on Instagram!
Пікірлер: 38
Happy Holidays sir. 🎄
Wow !! Like you I’ve never seen a leak like that ,good that job cane to you and fix . Happy new year
Job well done, amazing how much easier it is with the correct tools. Have a good Christmas, bearded one.
Great How To Video. Im glad the tool worked as intended. I appreciate the shout out and link to the ad. Keep on Veedubbin!
@wickedwerks
6 ай бұрын
Of course! Thanks for watching! ✌🏻
What a fantastic puller I've spent hours getting those bearings out!!
perfect timing, I was looking at the 59 and both sides have tell tale signs that the seals are both leaking. I probably should NOT flat tow that home 30 miles. Thanks !! And I think I did buy that same puller off the samba bceause getting that f n bearing off is a bear - I welded to my first one (62 bug). But we are to get smarter as time progresses.
Great job !
This is the very next job I need to do on one of mine. Great video, subscribed. Many thanks
@wickedwerks
6 ай бұрын
You’re welcome, thanks for watching and good luck!
That puller is a game changer
@wickedwerks
6 ай бұрын
Really is! He’s got a couple of helpful tools
Another great video! I noticed the rusty sludge started oozing out of the bottom of the new bearing. Where was the rusty sludge coming from? Is the residual sludge just so nominal that one need not worry about it? I'll be doing all this on my Beetle sometime in the next few months so I'll put this video and your comments in my how-to library.
@wickedwerks
6 ай бұрын
It’s coming from the axle tube. I sprayed the bearing out with brake clean before putting the cap back on. Once I get a couple 100 miles on it, I’ll change the gear oil again. Only way to get the majority of the schmoo out with pulling the axle tube to wash it out. This video will NOT apply to your Super Beetle as you have an IRS rear end. I have a video on doing the rear suspension on my bay window Bus that is applicable to your Super. Good luck!
@TrixedOut
6 ай бұрын
@@wickedwerks Thanks for the great response and great advice. I will go look for that video and put that in my how-to library!
Sehr gutes Video.. 👍 weiter so 🤙🏻Abonniert ✌️
According to the Bentley manual for pre 59 cars, they don’t show the paper gasket for the carrier area. Would you use it anyway? Bentley only shows the O ring seals.
@wickedwerks
6 ай бұрын
Yes.
@jeffbannon1345
6 ай бұрын
Thanks. What sealer do you use on the paper gasket?
@wickedwerks
6 ай бұрын
@@jeffbannon1345 permatex “right stuff”
@jeffbannon1345
6 ай бұрын
@@wickedwerks thanks!
👍👍
Where can I get one of those pullers
@wickedwerks
2 ай бұрын
Link in description for an ad on thesamba.
Should you not have put plenty of bearing grease into the new bearing before sliding it onto the shaft?
@wickedwerks
5 ай бұрын
No, bearing is lubricated by the transmission oil.
Sounds like you're fighting the weather also
@wickedwerks
6 ай бұрын
Yeah, it’s stupid cold and that propane heater doesn’t do much 😂
Sometimes I wouldn’t mind seeing how you clean parts and stuff.
@wickedwerks
6 ай бұрын
Sometimes I do, most of the time I can’t be bothered 😂 in this case I just used simple green, hot water and a bristle brush. Hit the seal surfaces with 0000 steel wool.
@rrs1550
6 ай бұрын
really.../? .brake clean, cotton rag... picture that..
@wickedwerks
6 ай бұрын
@@rrs1550 everyone has their own way.
So I got a question for you, sir, consider that burian. Was it under water? Why would you even consider cleaning it? Sort of throwing it in the garbage and replacing it with a new one. What the junk that was inside there, the lack of a proper lubricant. Those barren minds will consider them shot. The garbage thrum away put new ones in. They're really inexpensive. That thing was running around with basically water, dirty water in there. Don't reuse that my friend
hammering a new bearing into place, really.
@wickedwerks
Ай бұрын
If it can’t handle a few light taps with a hammer, it shouldn’t be on the car.
@enoz.j3506
Ай бұрын
@@wickedwerks And when they are hard to fit on the shaft ,hammer more,come on, teach the right way, or not at all. Bound to be new guys/girls doing this.
Great video. I just picked up a 1960 VW and it’s making a weird sound from the rear. I found this video on KZread and it’s exactly what mines is doing kzread.infojDOTO4ipL8U?si=Uq1l8wZVukgbRqu9 Is that the same thing yours was doing? Thanks