Rented a plate packer and ran out of diesel. Rental company said that the whole fuel system has to come apart to get the engine started again. Tried this trick and started immediately. Saved myself several hundred $$ in “repairs” by the rental company! Thank you for this video!

@carquestions

11 ай бұрын

Anytime Phil - cheers from Canada!

I just used this method this afternoon on my 1973 IH tractor. It worked great. I told my neighbor, who's farmed all of his life about it. He never heard of it but I bet he tries it.

Red Green would be proud as a peacock. I'll never forget his Car-B-Que episode. Greetings from rural BC. :-)

This saved my day. Ran out fuel on my Ferguson 25 (1960, Perkins diesel). I sprayed start gas and diesel. Thanks alot.

You saved my bacon!!! Thanks a bunch. We are traveling in a Sprinter van with a mercedes engine. This did the trick. Thankfully we are not stranded 500 miles from home.

@carquestions

6 жыл бұрын

Good to hear - cheers!

Tried this method on my Kubota MX5200 as a last ditch effort before disassembling the tractor to access the injectors. Had to use a little starting fluid in combination with the fuel spray bottle but it worked long enough for the injector pump to purge the air from the fuel system.... thanks for the great idea. mardyn

@carquestions

Жыл бұрын

Glad it helped Mardyn - thanks for the comment - Cheers from Canada!

Thank you very much for sharing! Worked great on a forklift I changed fuel filters on and lost all pressure to the fuel system. Even after filling the filters with diesel and trying starting fluid it wouldn’t start. This worked after I took the intake tube and sprayed diesel down the intake with the spray bottle. Also full fuel tank and charges batteries make a huge difference!

@carquestions

6 жыл бұрын

Glad to hear it worked - cheers!

This spray bottle to fire it up after changing fuel filter on diesel was a blessing. This was the first sure sweet easy way of purging or bleeding it it fired right up. I did push the throttle full at first. Thanks for the time saver.

@carquestions

2 жыл бұрын

Anytime John - Cheers from Canada!

Thank you for sharing this video - it was a real life saver. After 3 days of failed attempts to get my old Ford Backhoe running I was pulling my hair out, but this did the trick. I did find it easier to use a portable air compressor and a 'spray gun' usually used for cleaning - but filled with diesel it put out a fine spray, and I was able to keep the engine running for approx. a minute until the air was bled from the system, and it has been running since.

@carquestions

7 жыл бұрын

Excellent result -- nothing like the sound of an engine that is running like a fined tuned machine eh?

@traktorpriser

7 жыл бұрын

Exactly - I won't be forgetting this trick any time soon ;-)

Well that does look a shortcut, but it must depend somewhat on how much air is in the system, there is only so much the engine can pull to clear all the voids. This looks like a good thing to try after getting rid of most of the air, and pull the rest through.

@carquestions

3 ай бұрын

Let me know if it works - Cheers from Canada!

My case 1840 was down for 3 days. I bled the lines 3 times and nothing. I saw this video and tried it. It absolutely worked. Had it started in 10 seconds. Thanks bud!

@carquestions

5 жыл бұрын

Anytime Randy!

@benmiller7696

5 жыл бұрын

I've been cussing my 1840 out all afternoon. The only good thing is that if ran out of fuel in my shop. 38 and raining here in Iowa today so at least I was working out of the rain. I've bled it half a dozen times, sacrificed at least one 14mm wrench to the black hole, ran the battery dead and it's still not showing any signs of life. If this method works for me tomorrow I am driving to your house and giving you a big man hug.

Saved the day. Could not get the fuel to prime with the manual pump. Did as you demonstrated and she cranked right up

@carquestions

6 жыл бұрын

Good to hear - cheers Mark!

What a great Hack.......i just tried it on a Ford Trader and it worked well ........to think i believed all the bullshit about needing to bleed the system out..........thanks mate your a legend

@carquestions

2 жыл бұрын

Anytime Matt - Cheers from Canada!

this is what i do on small gas engines i dint know this could work the same way ,thank for this great tip , i hit the like as a ty

@carquestions

3 жыл бұрын

Thanks 808 - Cheers from Canada!

I have a New Holland TD5030 that sat for a couple of years. Could not get it to start. I bled every fuel line, injector, pump and filter I could find. Still would not start. I used a combination of diesel and starting fluid ( approved for diesel engines ). Sprayed and squirted the cocktail into the air intake. Took a couple of tries, but that engine roared to life!!!! Can't thank you enough for the idea!!!!

@carquestions

4 жыл бұрын

Glad it worked out Roger - cheers from Canada!

Thanks man, you just got my 96 350 started for me..

@carquestions

9 ай бұрын

Anytime BigBro - Cheers from Canada!

Did the second person have to give full throttle at the same time?

Worked a treat on my old 60’s fiat tractor. Thanks for the info, saved my bacon😂🤣

That's AWESOME!!! I bled my MF 135 and still didn't work. Then a cousin said to spray some diesel in there and it helped push it over the edge. I just wish I had seen this before I did all that bleeding. Oh well, now I know how to do it at least.

@carquestions

7 жыл бұрын

Smart cousin

@curtwpk1361

4 жыл бұрын

I don't have a cousin, so I got a neighbor. Didn't work. We found my neighbor's cousin to spray the fuel and it worked right away. I don't understand why its important to have a cousin here.

@rpruneau68

2 жыл бұрын

@@curtwpk1361 just cuz

thanks a lot! it really works astonishingly with my 4m40 engine and it saves me a lot of money.

@carquestions

7 жыл бұрын

No problem - anytime Alain

Thank you so much..it worked great..so happy it's running now

@carquestions

3 жыл бұрын

Anytime Todd - glad t0 help - cheers from Canada!

Just tried it on a '86 Ford 1210 and it worked like a charm. Sure beats the way I use to do it.

@carquestions

3 жыл бұрын

Glad to hear it - Well done Tmuss - cheers!

My first attempt, using your trick on my IH 364, didn't work. Removing the air cleaner still left a long tube to the intake. No diesel mist reached the engine. After removing the hood and air intake hose between the air cleaner and engine, the engine started. It seems you have to be very close to the engine intake for it to work. It does take 2 people, but is a tremendous time-saver.

@carquestions

2 жыл бұрын

I think you're right about that - the length of the intake tract determines how well it will work - Thanks Tom - Cheers from Canada!

Worked on my 434 international. Great thanks

@carquestions

5 жыл бұрын

Excellent - cheers Scott

I like this shortcut, you do tips. Thanks a lot

Thanks a lot - your tip saved me hours

@carquestions

3 жыл бұрын

Anytime Mike - glad it worked - Cheers From Canada!

Nice trick! I wish I would've known about this trick when I ran my 2001 dodge ram 2500 with the 5.9 Cummins out of fuel. The fuel guage was reading 1/8 of a tank so at the time I didn't realize it was actually out of fuel. After a shop charged me $2300 to change out the injection pump, I once again ran out of fuel thinking the guage was accurate and that's when I finally put 2 and 2 together.

@rusco321

7 жыл бұрын

I did put about $50 dollars worth of diesel in after the first incident, filled the filter bowl with diesel, but I didn't know enough to crack the lines open or use a spray bottle filled with diesel. Expensive lesson learned.

@carquestions

7 жыл бұрын

Hope it saves you in the future

Add my big thank you to the list. Got an old Deutz engine on a light tower running after changing all the rotted fuel lines. fired right up.... I cant even see the injectors on this thing but the air cleaner was easy to get to.

@carquestions

5 жыл бұрын

Anytime Paul - cheers!

It told my buddy about this DTJ dump truck Joe usually he'd I say I knew about that not this time time lol

I followed your advice in starting up our Ford 420 tractor after the fuel pump was rebuilt. Like a number of other commenters on this video, I had to use some ether to initially get it going. I sprayed shorts bursts of ether and diesel alternately until it took off. I'm not sure why the diesel alone did not work (I tried this first). Do you know why the diesel alone would not do it?--Thanks for this video!

@carquestions

2 жыл бұрын

TS - I think the intake tract of some diesels is shaped in such a way that little spray gets to the cylinder - the ether is more atomized and explosive so it does make it in - but you don't want to keep spraying it any longer than you have to. Cheers from Canada!

@ts8538

2 жыл бұрын

@@carquestions Thanks. That sounds about right. Anyway, it was fun shooting stuff in with both hands while yelling at my friend to give it more throttle.--Most excitement I've had in a long time.

Excellent idea. Why didn't I think of that?!

Whats the difference between doing this and starter fluid? I have this starter fluid that advertises works on diesels and it seems to start my Vw rabbit caddy 1.9L mechanical up just fine

@daalhoffarm

4 жыл бұрын

With using gas or starter fluid a diesel engine will knock and will pre ignite to fast. I made that mistake myself on a Yanmar diesel 2.4L

Will this work on my turbo 4.1 liter Perkins 4 cylinder engine once I replace the fuel filter ? No need for bleeding? I'll fill fuel filter with diesel first.

@carquestions

6 жыл бұрын

It should - try it and let me know how it works

I have a 3 cyl Kubota tractor that wont start , I have have been bleeding and cranking for 3 days. Shop manual procedure is not helping so I will try this. I have some ether based Easy Start but this looks safer . Fingers crossed !

@martinv7651

4 жыл бұрын

Same situation: JD5300 with a 3 cyl Yanmar, have gone through this before, this time even pressurizing the fuel tank didn't work. Saw this yesterday afternoon after a bloodless :) day, going out to try it now.

@martinv7651

4 жыл бұрын

Started right up! Thank you, thank you, thank you!

Is there any danger that running the injector pump dry at ~high speed might damage it?

@carquestions

5 жыл бұрын

A minute or two won't hurt

You could also do it the correct way & open the bleed screw on the connection where the fuel goes into the injector pump. If the thumb screw is missing you just open it with a pair of pliers or multigrips.

@carquestions

3 жыл бұрын

Tried that - sometimes they are blocked with crud - good tip though - thanks

@heybird5660

3 жыл бұрын

@@carquestions undo the nut retaining the needle valve & screw it right out & clean it. Its a shit set up & i dont know why kubota have it. Actually when i bleed them i do that anyway you can see when all the air is gone.

@carquestions

3 жыл бұрын

@@heybird5660 Did that after I got out of the hog pen - need to work fast with a 500 pound hog eyeing you

@heybird5660

3 жыл бұрын

@@carquestions yeah i can understand that i,m glad it was you & not me hahaha

@C-Fury_LTD

2 жыл бұрын

@@carquestions Real world pressures - you do what gets you out of trouble fast - great tip, thank you!

thank you so much, I tried it on Massey Ferguson 135 year 1974 loader tractor , it is very difficult to bleed injector nozzles, worked very well, appreciate

@carquestions

3 жыл бұрын

anytime cheers from Canada

@moyreyes3508

2 жыл бұрын

Have the same one cant start it either. Gonna try this wish me luck

@stevenwarner3029

2 жыл бұрын

I'm going to try this on my Massey 255 is weekend. Because it hard as **** to do it any other way

Thank you! Cool trick! :)

Cool I will have to remember this tip.

@carquestions

7 жыл бұрын

It works good Z

I have a 5.9l 12v mechanical and it won’t pull fuel past the injection pump, would this be something I can do?

@carquestions

5 жыл бұрын

lift pump maybe

@swatpigbbq

5 жыл бұрын

carquestions yes, it’s in the mail lol

I replied to Frank Grant's post, but for those who don't read replies- this worked fantastically on my JD 5300. Many thanks Mark!

@number1genoa

4 жыл бұрын

Unfortunately no luck for me , even with the filter removed and spraying it directly into the manifold only got a couple of coughs, Next step is to consult a technician as I have run out of options.

Saved me man saved me thank you

Thank u very helpful

Fast and easy. Thanks for sharing

@carquestions

7 жыл бұрын

no problem sunny

@sunnysacto

7 жыл бұрын

Learning with KZread folks is excellent. From Sunny CA Valley

@sunnysacto

7 жыл бұрын

I replace fuel filter, now I can't get fuel to injector. Your method didn't help :( Any ideas? Filter is loaded with fuel.

CAN it also work on a Jaguar X type? I changed the injectors and now the engine won’t start. Also does anybody know why the car make this huge TAK TAK TAK noise when I start it with starter fluid?

@carquestions

5 жыл бұрын

don't use starter fluid - use this method

@Jeremybaland

4 жыл бұрын

DO NOT use starter fluid in a diesel. It combusts at a different time and can crack the piston.

I got a Case 530 ck I have done a little bleeding work but still has air. Do you think this method will work? Also I am new to diesels so my biggest fear is that thing trying to take off and runaway and not being able to stop it covering the top intake.

I've used a couple snorts or ether when I blew a line on a tractor, always sounds awful for a min or 2, I like this diesel spray bottle alot better. I've heard of guys going this with WD 40, not sure how good it is on the engine though.

@carquestions

6 жыл бұрын

Thanks for the comment wreck!

@amg9856

6 жыл бұрын

Shouldn't use either. The diesel should be fine. Might want to wipe it done inside after your done to prevent debris from collecting in the system. Ether can really damage your diesel engine. A lot of diesel engines tend to have issues that stem from improper use causing wet stacking to the exhaust system. You typically want to use them at a minimum of 60% torque ratio. Even if you don't have a dpf your engine still needs to meet this. If your engine is running in idle for more than 10 minutes you are hurting it. This will lead to the exhaust to start to back up in the system, and you'll notice the soot building in your pipes when you remove the exhaust from the manifold. It with make its way more in-depth, and start breaking down the system. Not all ports of your glow plugs are large enough to get a borescope into, but if you can get one in there you can start to realise the damage that is being done.

@amg9856

6 жыл бұрын

This is also where indications of ether being used can be seen.

@richardc7721

6 жыл бұрын

WD40 is easier on the engine than starting fluid. Key to it is easy on the fluid. Another way is to take cheese cloth and spray a small amount of gasoline on it while the rag is covering the intake opening. Only gas vapor will be drawn in. Learned that 40years ago from an old time heavy equipment field mechanic. Used this method many times over 4 decades with no issues.

@nivanah4018

5 жыл бұрын

@@richardc7721 so would work ok on a komatsu dozer

Does anyone have experience with single cylinder diesel engine KM186FAG or 186f generator starting this way? I am going to try this one on KIPOR KDE6700TA3 generator. It has been constant pain to start it. New gas pump, injector went for inspection, bleeding air every time, changing fuel for fresh one still no avail. Also, I'll try to warm air intake with heater. Saw a guy doing it and it went very good.

@carquestions

7 ай бұрын

Is the tank mounted above the engine?

@Bbrezo

7 ай бұрын

@@carquestions Yes. Its slight in the front of the engine but above engine level. Then fuel goes down to the pump which is crankshaft driven and high pressure to injector. Return fuel goes back to tank. Thank you.

I've done this before with Aerostart fluid (not sure what the same stuffs called in Canada?). Never thought of diesel in a spray bottle though...great idea. Hope some dude doesn't try this with petrol in a spray bottle with his petrol engine.LOL

@carquestions

7 жыл бұрын

Wouldn't be good - thats for sure - in Canada we just call it ether or starting fluid

great video☺

@carquestions

7 жыл бұрын

Thanks - hope it saves you some time

I'm a diesel noob and I'm just asking if anyone could please explain how this method bleeds air out of the fuel system? Thank you

@carquestions

4 жыл бұрын

The fuel systems are supposed to be self priming to some extent but most don't do it it well at cranking speeds - if you can get the engine running at higher speeds and for a couple of minutes then the fuel pump most times will suck in enough fuel and purge the air itself and you're off to the races

@Clare.1985

4 жыл бұрын

@@carquestions thank you

What about intercooled turbo engines?

@carquestions

5 жыл бұрын

Bypass the intercooler

My 2009 f350 is having this problem right now. Is there any possobly harm to the engine doing this ??

@carquestions

5 жыл бұрын

Nope

I really hope this works I'm in a real jam here. shouldn't have bought a diesel I'm not educated enough on them.

@carquestions

6 жыл бұрын

It'll work if the fuel system is in good shape - no leaks or broken parts

worked like a charm on my MF245 after I bled the system to no luck. Sprayed into the air intake for about a minute (stopped halfway through to let ignition coil cool down per MF handbook). Will have to remember this in the future!

@carquestions

6 жыл бұрын

Excellent result Richard!

@michaeldickson3703

6 жыл бұрын

A diesel wouldn't have an ignition coil surely?!?

This is good for a boom lift too??

Will this work on a turbo diesel engine

@carquestions

6 жыл бұрын

Yep - no problem -

You got away with it because it's an old indirect injection non-turbo. Do that on a modern common rail, you might hydro lock the engine = busted piston or bent rod, or burn up high pressure pump due to no lubrication.

yea buddy! gittin er done!

@carquestions

6 жыл бұрын

Works like a charm

Will this work on a kubota MX4700 tractor?

@larrydavis2703

3 жыл бұрын

Worked like a charm! Thanks for sharing!

@carquestions

3 жыл бұрын

Anytime Larry - Cheers from Canada!

I accidentally put gas in my bobcat .I think I caught it in time . I'll try ur technece when I drain the tank.thanks

@carquestions

4 жыл бұрын

let me know how you make out

@kylebykiv7771

4 жыл бұрын

I would suggest cracking the lines off at the injectors and bumping the lift pump with diesel in the tank to clear the lines. This technique does work but it’s hard on your injectors

We'll see tomorrow , been bleeding for a week , no results .

If you have air in your system, you have to remove the air. Sometimes you have to bleed it

I don't know how many times I've replaced my lift pump in my thomas, finally dumped it and replaced with electric now it bleeds with a turn of the key.

@carquestions

6 жыл бұрын

I hear ya Max - good info

Thank you, Thank you, Thank you, Thank you, Thank you. It works and is so easy,

@carquestions

4 жыл бұрын

Glad it helped Mike - cheers from Canada!

1903? Is that the model or the year?

@austinhammett9304

4 жыл бұрын

1.903L of displacement

Hi, can i spray diesel diesel on OPEL zafira 2.0 dti? or do i need starter spray?

@carquestions

4 жыл бұрын

Yes - won't hurt anything

What Are You spraying?

@carquestions

4 жыл бұрын

Diesel fuel

@cbr1thou

4 жыл бұрын

Hoss piss

My John Deere 3042e did not work it was useless why?

@carquestions

Жыл бұрын

other issue besides fuel? - mechanical maybe

Never seen anyone use diesel before 🤔. That’s so much smarter that using gas or start fluids which can damage is engine.

@carquestions

3 жыл бұрын

Just makes sense - Cheers from Canada Diesel

Aww man it's not working why??? It started for 30 seconds and died and started for short bits but now it won't do anything

@noahmira4788

11 ай бұрын

probably more air in the fuel lines

im getting told even though i have it running there is still air . it runs fine until i use it ,, it surges and eventually dies , it will start again on its own . It was doing that before i had to bleed lines. I know somebody knows what this is .

@carquestions

6 ай бұрын

Happens to us all Owl - let us know what type of make and model you have and maybe some people can offer some advice - Cheers from Canada!

@Owl4909

6 ай бұрын

@@carquestions 80s JD 410 backhoe

I tried it on my Perkins AD4 engine in my Backhoe and it didn't work, I just had to keep working to get the air out of the system after changing the secondary fuel filter, I didn't think I was ever going to get it going.

@kenvoigt3636

4 жыл бұрын

I know what you mean, I got air in my system after changing the secondary filter, I must have pumped the handle on the fuel pump 2,000 times and finally gave up that it was going to pump anyting, I had to send for a pump and it was made in China and also pumped nothing, I then sent for another pump, this one had no name on it or any numbers and it pumped nothing, I finally gave up and had to invent my own electric pump system and it works good, my backhoe is a 1971 model MF.

@number1genoa

4 жыл бұрын

@@kenvoigt3636 We had the same problem on the Perkins 4108 in out yacht, they are notoriously difficult to bleed. We installed a primer bulb from a OB fuel tank, works a treat.

wath s his name mtors

Gasoline soaked rag works also.

@groundeddutchman5852

4 жыл бұрын

Thats how we always did it on the farm.

I'm so frustrated and confused

Just did this to my Kubota grasshopper. Pretty sure major engine damage was achieved due to over revving.

@carquestions

9 ай бұрын

How much and how long did you spray?

@FellerofTrees

9 ай бұрын

Most grasshopper diesels have a label on the air filter assembly specifically telling you not to do this.

There will still be so,e air in the system...might need to bleed it again.

@carquestions

7 жыл бұрын

This machine has run fine ever since no need

Are you foolin me. It’s that easy

@carquestions

6 жыл бұрын

Yep = works like a charm if nothing else is busted

i am gona try it on my yanmar tomorrow

@carquestions

6 жыл бұрын

hope it works for you

@TheDoughGetta

6 жыл бұрын

Did it work?

Awsome/easy too

@carquestions

4 жыл бұрын

Hope it helped Scott

This is a much better way than starting fluid.

@carquestions

6 жыл бұрын

Safer for sure

@thatbiguy1975

6 жыл бұрын

im confused- im new to diesel and i hear this said a lot buy my 73 ford 7500 construction backhoe loader came from the factory with ether injection and no glo plugs. the old guy i bought it from said he has been starting it with ether/starting fluid for over 20 years he owned it with no problems so thats what i do. only needs a shot if it's cold or sitting for a long time maybe. seems wrong to me but must be ok??

@carquestions

6 жыл бұрын

J - this procedure isn't for normal starting - its for when you have run it out of fuel and it won't prime - keep using your starting method for normal starting

nam motors please

@carquestions

7 жыл бұрын

please improve your question or write it in your own language and I'll try to get it translated

Newer diesel machines have turbo. The intake is not accessible.

@carquestions

4 ай бұрын

Good point LJD -- so spray way more - they still suck air one way or the other Cheers from Canada!

@lumberjackdreamer6267

4 ай бұрын

@@carquestions From the air intake, there’s the turbo, then the inter cooler, then potentially the throttle plate, and finally the intake manifold…

@carquestions

4 ай бұрын

Your right - a lot of stuff - but they still run if the turbo goes - so spray only while cranking it has to get in at some point doesn't it?@@lumberjackdreamer6267

@lumberjackdreamer6267

4 ай бұрын

@@carquestions The turbo doesn’t spin when cranking. Turbo needs high velocity exhaust gases to spin.

@carquestions

4 ай бұрын

Even if the turbo is broken and doesn't spin air goes past their blades doesn't it. Turbo blades are shaped to push air - they don't have any seal like a valve does - my point is air will get through the turbo even if it isn't spinning - turbos are not air tight designs.@@lumberjackdreamer6267

Didn’t work, even though we followed your step-by-step tutorial- after replacing the fuel filter on a 1220 Ford HST diesel tractor, it won’t start, have to get a more specific solution for this engine-will deal with it in the morning, thanks anyway.

@carquestions

6 жыл бұрын

Try a little bit of ether - if that doesn't work your spraying it on the wrong side of the turbo - the diesel in the video had no turbo

@kevedamanyo

5 жыл бұрын

does it hurt the turbo? or supposed to unhook stuff and go on back side of it? my 6.5 Detroit is not running more than five seconds has relocated Pmd, new filters, screen, lift pump, purged return line to bubble thru tank, no explanation other than bad IP. but runs great when it starts for five seconds then stall and wait few hours starts again. if your idea keeps it running then I have a fuel problem, not an IP prob....I was ready to order IP until this video. I tried this myself and still stalled, but when I get a second person to crank, going to try again, here's to hoping. but I can't spray before the turbo? it's ez to spray in with air filter removed, but needs some tools involved if have to avoid turbo

Trying on a MF110, Ran on fumes, lol

@carquestions

Жыл бұрын

Did it work? Cheers from Canada!

the air in the fuel lines might be gone but... the bubbles are still there.. lol!

@carquestions

6 жыл бұрын

long gone after a few minutes

Saved me a lot of headache. I used wd40

@carquestions

6 жыл бұрын

Great result......cheers!

No piglets were injured whilst making this video...........

@carquestions

6 жыл бұрын

Thats right

I think my lift pump is out

@carquestions

6 жыл бұрын

If the fuel fails to get to the injection pump then you are right Jervino

@jervinosmith6270

6 жыл бұрын

Yeah i jump out my fuel relay and no fuel came up by the injection pump

That don't always work!

@carquestions

Жыл бұрын

Ya - some systems have various bends or valves in the way - but in theory if you can get it past the intake valves .....

@radamson1

Жыл бұрын

@@carquestions I have used it hundreds of times along with pulling, using wd40 and a half a dozen other tricks. But some times you just have to bleed the lines.

Have anyone tried on a diesel car?

@carquestions

6 жыл бұрын

Yep - it works Oscar

Terrible idea. A diesel is supposed to have hot compressed air and be timed by the start of injection. This is providing fuel and letting it ignite whenever compression is high enough. No control over timing. Easier way - crack your bleeder, take the fuel return line off somewhere, crack the bleeder and shoot a small amount of compressed air into the tank return fitting with a portable tank and a blow gun, then put your finger over it. Not a lot, just enough that there is a small amount of residual pressure in the tank. Too much and you can rupture the tank. Keep going until steady fuel comes out of the bleeder, then tighten the bleeder and hook the vent back up. If you didn't crank it too much and get air in the injector hard lines it will probably fire instantly.

@carquestions

3 жыл бұрын

Terrible idea - your truck, tractor or Bobcat etc never breaks down near an aircompressor - and I can count on one finger how many people carry around an air pig that is full - jumper cables yes - air pigs no

@AS-we9xi

3 жыл бұрын

@@carquestions ok.. How many people carry around a 2nd set of pistons and rings for when you crack the lands from letting it preignite.

cut the first 1:30 of the video... too much talking and walking... just get the job done

@cleric022684

6 жыл бұрын

make your own video fool

@gyffjogofl7676

6 жыл бұрын

I thought it was a great video.

@oby-1607

6 жыл бұрын

I thought the piggies were gonna be more involved.

@JHorse508

5 жыл бұрын

Wow the vid was literally just over 3 mins

@adamcreager770

3 жыл бұрын

Your wife’s a lucky girl. “Just get the job done...” lmao 😂

If you have air in your system, you have to remove the air. Sometimes you have to bleed it

@carquestions

Жыл бұрын

Yes that's true but once running most systems will bleed air out quickly and high rpm (running helps a lot)