The broken bearings were joined together with the skill of a mechanical welder
Жүктеу.....
Пікірлер: 122
@wellingtonsouza270820 күн бұрын
O rolamento do final do vídeo parece que é outro não consegui ver a marca da solda e não mostra colocando a grade das esferas
@user-yl5ry6if5y
17 күн бұрын
Как всегда обман
@Frn2304
12 күн бұрын
Exatamente, o último rolamento na máquina está com a gaiola das esferas, e o que ele estava soldando ele não colocou a gaiola, ou seja, fake
@katkov00027 күн бұрын
По окончании ролика подшипник выбросили.
@user-my4fo2hr3o
22 күн бұрын
По окончании ролика подшипник был установлен на ладу Калину😂😂😂
@user-dv1rg7oq5r
15 күн бұрын
Естественно , эту шнягу снимают для просмотров .
@dryndelldryn9872
14 күн бұрын
Я один наверно заметил что это два разных подшипника, 22:58 он резко изменился. Или это один подшипник только в конце какой он был до того как его распилили, и отремонтировали. Забавно что его вынули из маленькой механической коробки. Все знают что в коробках передач используют только таких размеров подшипники.
@user-md5ju7jm3v19 күн бұрын
Видно что новый подшипник в конце ролика😂😂😂
@Jekerson122 күн бұрын
Заварить подшипник 😂😂😂 доктор дью вышел из чата.
@EvgenKum
20 күн бұрын
В конце ролика совсем другой подшипник. По времени : 22:55 завареный подшипник, а в 23:00 уже новый😂
@user-pw5us9xf8m
19 күн бұрын
Как его токарь допустил к станку,это издевательство над станком
@-_---__------________
18 күн бұрын
@@EvgenKum , По тому что шарики было не распределить, из-за сужения кольца при сварке! (Я только сейчас это понял, благодаря вашей подсказке)
@samspade975
15 күн бұрын
Bulchit, or should I say ball chit 😂😂
@samspade975
15 күн бұрын
Bulchit, or should I say ball chit 😂😂
@user-ff8nx9cs6v10 күн бұрын
I always repair my car bearings like that. And now it runs faster than ever.
@holycrapski20 күн бұрын
I think the recorded the video round way wrong and ended at the beginning. And that makes more sense than the video.
@richardmiller523822 күн бұрын
Didn't show cage being installed
@rogerioalvarez87313 күн бұрын
Man what a wonderfull idea...i will copy it and fix bearings thisway and make a millon dollar very soon...stay tuned as soon as i make it i will let every body know...
@user-te2rv3dj1k27 күн бұрын
Сепаратор как там оказался 😅😂
@user-hj3yb8uf6o
26 күн бұрын
Ну вобшето сепоратор ставится в конце сборки подшибника ,а так да куда его поставть после этого 😢хотя можно думаю нашим диайвайшикам с утуба😂😂
@pauloacedo746124 күн бұрын
This method will never preserve in and out bearing dimensions
@SuperArgentun
24 күн бұрын
Claro y tu les vas a enseñar a ellos a trabajar??? Jajaja
@pauloacedo7461
24 күн бұрын
@@SuperArgentun of course Yes, if YOU knew anything about mechanics you would notice the last bearing showed is not even the same broken one ,its a new bearing ... but your concern is about MY comment...
@-_---__------________
18 күн бұрын
Какие проблеммы? Наварят или сточат лишнее...
@vojvoda9060
16 күн бұрын
It will work.....about 10 min.😂😂😂😂
@herberar
9 күн бұрын
I wonder what happens to the termic treatment of the bearing surfaces after welding.
@ferrockherrera639122 күн бұрын
Ese tipo ha destrozado años de investigación ya desarrollo
@gilbertomanvailer207011 күн бұрын
Parabéns pelo ótimo serviço!!!
@bumbarash8551Күн бұрын
Улыбнуло 😁. Запчасти для Роскосмоса.!
@raminarshadian320927 күн бұрын
You waste my time 😢it is a Fake video....
@EddywaKenya26 күн бұрын
this will work! but in pluto! good jov
@ruslantanroverdiev606117 күн бұрын
Вы кого пытаетесь обмануть?
@Zoli04925 күн бұрын
There may be many things that can be solved, but not this. The idea was good.
@SPUDHOME15 күн бұрын
Hand grinding a bearing race? Not polishing a ground bearing race? Maybe in holland for a very slow speed windmill, for a temporary repair. Then not.
@altafahmed138419 күн бұрын
MASHA ALLAH GOOD
@rosewhite---20 күн бұрын
that bearing never came out of that gearbox! When it has been welded and ground by hand it will be fit for nothing but making a clickbait video!
@thepubliceye22 күн бұрын
Click bait, nothing more.
@user-zu1er3is3h12 күн бұрын
Qual é a Referência deste eletrodo de solda e o 7018?
@goldCrystalhaze12 күн бұрын
By continuing to repair this (or any) other bearing by arc welding it on his lathe, he is increasing his chances to worry about his own bearings very soon...
@tengkusulaiman10 күн бұрын
I always have bad luck with bearings. My motorcycle engine breakdown twice due to bearing break. Twice and thousand dollars need to repair. With this type of bearing restore, I don't think it give any better luck after repair
@georgebrehm862214 күн бұрын
Yes they will be when they are machined on lathe,the size of outer case is known, it is then checked with micrometer ,
@donnienicholson606227 күн бұрын
22:56 No cage missing 3 balls.....23:00 cage and all balls inserted. Was it magic???
@vilasboas0306
27 күн бұрын
Foi o que eu pensei também! 😃😃😃
@citymagnum4734
8 күн бұрын
Just good old switcheroo. A pity for all the work they put in though.... probably they decided to do this at the last moment, sfter they realized they fucked up the ball insertion by jamming them.
@advantechdesign2836Күн бұрын
@5:30 Does anyone else feel sorry for the lathe head-stock bearings? 😵💫
@user-iy2rs1yx3m16 күн бұрын
Болгарской сами прорезали,в коробке такого размера нет))))) развод
@-_---__------________18 күн бұрын
Из-за уменьшения размера при сварке наружного кольца, шарики было трудно распределить, это делалось молотком паспирая как клином место под шарик, и наружняя обойма невыдержала напряжения и лопнула. (трешина смотрит на человека) По тому что несущая способность поверхносной сварки на ШХ15 можно сказать никакая. По этому на 23:00 уже другой подшипник. Вобще такой тип, является тяжёлонагруженным, и я бы посмотрел как он залес на посадки, и работал в узле.😄
@citymagnum47348 күн бұрын
22:57 switcheroo? Suddenly the balls are properly spaced, roller cage is mounted, and the inner race no longer has a visible welding mark.
@juancarbajal38202 күн бұрын
Tanto tiempo viendo el video oara que al final pongan un rodamiento nuevo a quien quieren engañar
@user-zl3zi6hq5o14 күн бұрын
подшипник деталь не ремонтируется а заменяется так как поломка будет серьезная потом.последствия.
@user-ev6rw6kj3q13 күн бұрын
Теперь я видел все. Ещё бы ХАДО заложить .😂
@juancarbajal38202 күн бұрын
Que tomada de pelo jajajaja al final cambiaron el rodamiento por uno nuevo jajajaja
@Neblogeriztrusheb10 күн бұрын
Так и не понял я каким образом он собрал воедино подшипник 🤔
@josuepauferro437320 күн бұрын
Eles trabalham com o que eles tem disponível !
@advantechdesign2836Күн бұрын
@0:27 Sure. That bearing came out of that gearbox. Sure it did - not.
@glennschemitsch834114 күн бұрын
Any bearing is better than no bearing I guess.
@arthurm.595217 күн бұрын
Those repairs have gone too far. It was just filmed for content. The will throw it away after the video. They showed a different bearing at the end
@victormontecinos375521 күн бұрын
Pan para hoy dia hambre para para mañana,que trabajo mas chancho si se somete a la misma presion que produjo el quiebre garantizada la rotura y en el mismo lugar.
@kishanlal198322 күн бұрын
Ye bering nahi chalega
@user-lk6bv6lu6t10 күн бұрын
Внутренняя обойма лопнула и стала по размеру больше,значит на валу будет болтаться.Кроме того сварка отпускает металл,ухудшая его твердость.
@fouzibenmebarek769823 күн бұрын
It is not the same piece that does not laugh at our minds
@antongyrt481414 күн бұрын
Это такой прикол?
@joaomarcos739416 күн бұрын
esse rolamento vai roncar com certeza ou rasgo meu diploma de tecnico mecanico se nao
@prakashas74903 күн бұрын
How he insert the ball locks inside the bearing,, at last it is a new bearing on the lathe machine,,, fake
@gustavohenriqueF126 күн бұрын
Great and Nice Job.👍.
@saulogomesdasilva-wq5lv23 күн бұрын
Só um leigo acredita nisso, no final do vídeo sai de cena o que foi soldado e entra outro que aí recebe uma maquiagem com uma lixa... KKKKKM
@jamesbrooks982817 күн бұрын
What this is a boat anchor
@hernantobarbosadasilva16 күн бұрын
Houve trambique aí...
@pekpks734719 күн бұрын
Where resources are scarce this type of recovery ends up being the only chance... But it doesn't look good, this bearing broke due to a tolerance error in the fitting
@user-ib2ck3eb4l26 күн бұрын
Лютая дичь
@vanthieunguyen789726 күн бұрын
Dùng được 21 ngày
@ryanrhotama52526 күн бұрын
Are u think viewers is not know, in the end, uuse another bearing
@adriankohli487011 күн бұрын
I think it won't work🤔
@rezafarhjou303226 күн бұрын
ماشاالله ❤❤❤
@kornelijekovac979320 күн бұрын
Not sure that weld will hold.
@freddykoehler711827 күн бұрын
Gute Arbeit 😊
@MS0076127 күн бұрын
This is really awesome
@randomclicks917
27 күн бұрын
@@user-wk6kw8bo7sit’s mean they cheating with us??
@mauriziograndi17505 күн бұрын
Now here we are going too far. I admire those people occasional emergencies repair but here we make not only a wrong things but we teaching younger apprentices the wrong things. The welding there as everyone knows let that outer ring shrink dramatically, in fact someone use to tack the ring to remove a collapsed bearing from a recess housing when is difficult to remove it with normal means, because doing so will shrink and removes easily. Moreover the last ball will be difficult to re-insert or is to be left out.
@najeebullah115527 күн бұрын
Amazing.
@randomclicks91727 күн бұрын
This man have great skills hmm😮😮
@nevorotov27 күн бұрын
фейк
@adriankohli487011 күн бұрын
i think, it's dosnt Work🤔
@DiscoveringSkillsOfficial51227 күн бұрын
wow amazing
@victormontecinos3755
21 күн бұрын
Horrendo
@xn12ztq15 күн бұрын
Всё это смахивает на вброс дерьма на вентилятор. Тысячи язвительных или восторженных комментов, капает бабос за просмотры!
@ertilx1121 күн бұрын
saçma bir çözüm.
@adrianrodriguezrosa718323 күн бұрын
No se lo cree ni el😂
@kamil___diamondautoenginee487014 күн бұрын
sorry but this is not work
@pkfan511215 күн бұрын
Will not last
@waynekarjala203225 күн бұрын
Does anyone think this is real?
@advantechdesign2836
Күн бұрын
Not me!
@eldiablo8881420 күн бұрын
Даже если это правда это такое г**** бы в тачку бы не поставил
@lennoxramberran145917 сағат бұрын
This job did not impress me at all, it is not strong and durable also the broken edges need much more beveling to accommodate more welding, that's my view, viewer from trinidad
@shahidwahab421621 күн бұрын
Jab goli ki jali fit karna thi jo asal fankari thi wahan chacha video gol kar gya yeh koi skill nahi
@user-nr7mb8uz9w26 күн бұрын
Ces gens ne reculent devant rien pour faire de l'audience
@simoncustom609016 күн бұрын
Сварка каленой высоко углиродистой стали обычным электродом.... без комментариев вообще, разделки никакой, провара соответственно тоже, первые нагрузки и подшипнику пиздец
@vgen900412 күн бұрын
Понятно, что не от хорошей жизни такой ремонт, но работать это долго не будет, сварка в подшибнике это перебор, да не понятно как он с рулеткой в размер вышел
@josehernandoneiraramos564020 күн бұрын
El peor trabajo que ha echo el hombre sobre la tierra 😂😂😂😂
@john-wk4ks14 күн бұрын
this channel and may other that post hack repair jobs like this must have someone going around looking for broken parts they can hack back together and video the hack repair and if these videos are real and they charge for the job they are ripping people off by not doing the job right in the first place
@MakLauD_2La2 күн бұрын
Ээээ!!! Ребя!!! Ну вы совсем обнаглели шоле????? Какого ху, этот подшипник забыл в кпп и тем более на месте где должна быть корзина сцепления!!!! Вот тут диз однозначно!!!
@paveld854127 күн бұрын
😂
@fuentescg14 күн бұрын
🤣
@ilyalopys361624 күн бұрын
Вы это серьёзно?
@user-bh3qx8kp7j27 күн бұрын
😂😂😂
@nikosalexakis349411 күн бұрын
🤣🤣🤣🤣😂😂😂😂😂
@user-md5ju7jm3v19 күн бұрын
Бред полнейший
@julioarmandogomezc800412 күн бұрын
12:14 SÍ se puede ser un maestro en soldadura, también un maestro en el torno, pero NO PUDO SER UN MAESTRO EN ESTA REPARACIÓN TAN FALSA, MAS FALSA QUE UN BILLETE DE 13$.... TRISTEZA ME DIÓ HABER PERDIDO INÚTILMENTE 12min
Пікірлер: 122
O rolamento do final do vídeo parece que é outro não consegui ver a marca da solda e não mostra colocando a grade das esferas
@user-yl5ry6if5y
17 күн бұрын
Как всегда обман
@Frn2304
12 күн бұрын
Exatamente, o último rolamento na máquina está com a gaiola das esferas, e o que ele estava soldando ele não colocou a gaiola, ou seja, fake
По окончании ролика подшипник выбросили.
@user-my4fo2hr3o
22 күн бұрын
По окончании ролика подшипник был установлен на ладу Калину😂😂😂
@user-dv1rg7oq5r
15 күн бұрын
Естественно , эту шнягу снимают для просмотров .
@dryndelldryn9872
14 күн бұрын
Я один наверно заметил что это два разных подшипника, 22:58 он резко изменился. Или это один подшипник только в конце какой он был до того как его распилили, и отремонтировали. Забавно что его вынули из маленькой механической коробки. Все знают что в коробках передач используют только таких размеров подшипники.
Видно что новый подшипник в конце ролика😂😂😂
Заварить подшипник 😂😂😂 доктор дью вышел из чата.
@EvgenKum
20 күн бұрын
В конце ролика совсем другой подшипник. По времени : 22:55 завареный подшипник, а в 23:00 уже новый😂
@user-pw5us9xf8m
19 күн бұрын
Как его токарь допустил к станку,это издевательство над станком
@-_---__------________
18 күн бұрын
@@EvgenKum , По тому что шарики было не распределить, из-за сужения кольца при сварке! (Я только сейчас это понял, благодаря вашей подсказке)
@samspade975
15 күн бұрын
Bulchit, or should I say ball chit 😂😂
@samspade975
15 күн бұрын
Bulchit, or should I say ball chit 😂😂
I always repair my car bearings like that. And now it runs faster than ever.
I think the recorded the video round way wrong and ended at the beginning. And that makes more sense than the video.
Didn't show cage being installed
Man what a wonderfull idea...i will copy it and fix bearings thisway and make a millon dollar very soon...stay tuned as soon as i make it i will let every body know...
Сепаратор как там оказался 😅😂
@user-hj3yb8uf6o
26 күн бұрын
Ну вобшето сепоратор ставится в конце сборки подшибника ,а так да куда его поставть после этого 😢хотя можно думаю нашим диайвайшикам с утуба😂😂
This method will never preserve in and out bearing dimensions
@SuperArgentun
24 күн бұрын
Claro y tu les vas a enseñar a ellos a trabajar??? Jajaja
@pauloacedo7461
24 күн бұрын
@@SuperArgentun of course Yes, if YOU knew anything about mechanics you would notice the last bearing showed is not even the same broken one ,its a new bearing ... but your concern is about MY comment...
@-_---__------________
18 күн бұрын
Какие проблеммы? Наварят или сточат лишнее...
@vojvoda9060
16 күн бұрын
It will work.....about 10 min.😂😂😂😂
@herberar
9 күн бұрын
I wonder what happens to the termic treatment of the bearing surfaces after welding.
Ese tipo ha destrozado años de investigación ya desarrollo
Parabéns pelo ótimo serviço!!!
Улыбнуло 😁. Запчасти для Роскосмоса.!
You waste my time 😢it is a Fake video....
this will work! but in pluto! good jov
Вы кого пытаетесь обмануть?
There may be many things that can be solved, but not this. The idea was good.
Hand grinding a bearing race? Not polishing a ground bearing race? Maybe in holland for a very slow speed windmill, for a temporary repair. Then not.
MASHA ALLAH GOOD
that bearing never came out of that gearbox! When it has been welded and ground by hand it will be fit for nothing but making a clickbait video!
Click bait, nothing more.
Qual é a Referência deste eletrodo de solda e o 7018?
By continuing to repair this (or any) other bearing by arc welding it on his lathe, he is increasing his chances to worry about his own bearings very soon...
I always have bad luck with bearings. My motorcycle engine breakdown twice due to bearing break. Twice and thousand dollars need to repair. With this type of bearing restore, I don't think it give any better luck after repair
Yes they will be when they are machined on lathe,the size of outer case is known, it is then checked with micrometer ,
22:56 No cage missing 3 balls.....23:00 cage and all balls inserted. Was it magic???
@vilasboas0306
27 күн бұрын
Foi o que eu pensei também! 😃😃😃
@citymagnum4734
8 күн бұрын
Just good old switcheroo. A pity for all the work they put in though.... probably they decided to do this at the last moment, sfter they realized they fucked up the ball insertion by jamming them.
@5:30 Does anyone else feel sorry for the lathe head-stock bearings? 😵💫
Болгарской сами прорезали,в коробке такого размера нет))))) развод
Из-за уменьшения размера при сварке наружного кольца, шарики было трудно распределить, это делалось молотком паспирая как клином место под шарик, и наружняя обойма невыдержала напряжения и лопнула. (трешина смотрит на человека) По тому что несущая способность поверхносной сварки на ШХ15 можно сказать никакая. По этому на 23:00 уже другой подшипник. Вобще такой тип, является тяжёлонагруженным, и я бы посмотрел как он залес на посадки, и работал в узле.😄
22:57 switcheroo? Suddenly the balls are properly spaced, roller cage is mounted, and the inner race no longer has a visible welding mark.
Tanto tiempo viendo el video oara que al final pongan un rodamiento nuevo a quien quieren engañar
подшипник деталь не ремонтируется а заменяется так как поломка будет серьезная потом.последствия.
Теперь я видел все. Ещё бы ХАДО заложить .😂
Que tomada de pelo jajajaja al final cambiaron el rodamiento por uno nuevo jajajaja
Так и не понял я каким образом он собрал воедино подшипник 🤔
Eles trabalham com o que eles tem disponível !
@0:27 Sure. That bearing came out of that gearbox. Sure it did - not.
Any bearing is better than no bearing I guess.
Those repairs have gone too far. It was just filmed for content. The will throw it away after the video. They showed a different bearing at the end
Pan para hoy dia hambre para para mañana,que trabajo mas chancho si se somete a la misma presion que produjo el quiebre garantizada la rotura y en el mismo lugar.
Ye bering nahi chalega
Внутренняя обойма лопнула и стала по размеру больше,значит на валу будет болтаться.Кроме того сварка отпускает металл,ухудшая его твердость.
It is not the same piece that does not laugh at our minds
Это такой прикол?
esse rolamento vai roncar com certeza ou rasgo meu diploma de tecnico mecanico se nao
How he insert the ball locks inside the bearing,, at last it is a new bearing on the lathe machine,,, fake
Great and Nice Job.👍.
Só um leigo acredita nisso, no final do vídeo sai de cena o que foi soldado e entra outro que aí recebe uma maquiagem com uma lixa... KKKKKM
What this is a boat anchor
Houve trambique aí...
Where resources are scarce this type of recovery ends up being the only chance... But it doesn't look good, this bearing broke due to a tolerance error in the fitting
Лютая дичь
Dùng được 21 ngày
Are u think viewers is not know, in the end, uuse another bearing
I think it won't work🤔
ماشاالله ❤❤❤
Not sure that weld will hold.
Gute Arbeit 😊
This is really awesome
@randomclicks917
27 күн бұрын
@@user-wk6kw8bo7sit’s mean they cheating with us??
Now here we are going too far. I admire those people occasional emergencies repair but here we make not only a wrong things but we teaching younger apprentices the wrong things. The welding there as everyone knows let that outer ring shrink dramatically, in fact someone use to tack the ring to remove a collapsed bearing from a recess housing when is difficult to remove it with normal means, because doing so will shrink and removes easily. Moreover the last ball will be difficult to re-insert or is to be left out.
Amazing.
This man have great skills hmm😮😮
фейк
i think, it's dosnt Work🤔
wow amazing
@victormontecinos3755
21 күн бұрын
Horrendo
Всё это смахивает на вброс дерьма на вентилятор. Тысячи язвительных или восторженных комментов, капает бабос за просмотры!
saçma bir çözüm.
No se lo cree ni el😂
sorry but this is not work
Will not last
Does anyone think this is real?
@advantechdesign2836
Күн бұрын
Not me!
Даже если это правда это такое г**** бы в тачку бы не поставил
This job did not impress me at all, it is not strong and durable also the broken edges need much more beveling to accommodate more welding, that's my view, viewer from trinidad
Jab goli ki jali fit karna thi jo asal fankari thi wahan chacha video gol kar gya yeh koi skill nahi
Ces gens ne reculent devant rien pour faire de l'audience
Сварка каленой высоко углиродистой стали обычным электродом.... без комментариев вообще, разделки никакой, провара соответственно тоже, первые нагрузки и подшипнику пиздец
Понятно, что не от хорошей жизни такой ремонт, но работать это долго не будет, сварка в подшибнике это перебор, да не понятно как он с рулеткой в размер вышел
El peor trabajo que ha echo el hombre sobre la tierra 😂😂😂😂
this channel and may other that post hack repair jobs like this must have someone going around looking for broken parts they can hack back together and video the hack repair and if these videos are real and they charge for the job they are ripping people off by not doing the job right in the first place
Ээээ!!! Ребя!!! Ну вы совсем обнаглели шоле????? Какого ху, этот подшипник забыл в кпп и тем более на месте где должна быть корзина сцепления!!!! Вот тут диз однозначно!!!
😂
🤣
Вы это серьёзно?
😂😂😂
🤣🤣🤣🤣😂😂😂😂😂
Бред полнейший
12:14 SÍ se puede ser un maestro en soldadura, también un maestro en el torno, pero NO PUDO SER UN MAESTRO EN ESTA REPARACIÓN TAN FALSA, MAS FALSA QUE UN BILLETE DE 13$.... TRISTEZA ME DIÓ HABER PERDIDO INÚTILMENTE 12min
Not Strong
စောက်ရူး
It is a fake 🥱