Taking the CJ for a first Off-Road ride after the 5.0 swap. #jeep #cj #offroad #4x4
Жүктеу.....
Пікірлер: 16
@cj7andotherjeeps9408 ай бұрын
He got lucky he didn’t roll. Good save. Nice Cj.
@driftking555 Жыл бұрын
Just saw the thumbnail and liked the video ♥️♥️.... I wonder why not this kinda content goes viral 🤔
@GabesGarage
Жыл бұрын
+Drift King I be asking my self that, there’s a lot that I still need to learn when it comes down to KZread. Thanks for the like 😁
@bassment03 Жыл бұрын
Heck yeah Jake busted his butt to get the ole cj in prime running condition and that 302 sounds sooo good
@GabesGarage
Жыл бұрын
+bassment03 not bad at all for a first time after the swap. Nothing broke and it did everything he wanted to do.
@Teekay61711 ай бұрын
My dad had one it dominated all the new jeeps on the trails was AMC V8
@bassment03 Жыл бұрын
Great vid gabe 👏 👍
@JeepTJWheelin9 ай бұрын
That is one badass CJ-5, sounds really good too! I have an '05 TJ Rocky Mtn 4.0L, and it is by far thee best and most fun vehicle I've ever had. I'd rather restore a '41 - '06 Jeep than get an '07 - present day heep. Jeep Born: 1941 Died: 2006 O|||||||O 🇺🇲 Only in a 2 Dr 🇺🇲 '41 - '06
@GabesGarage
9 ай бұрын
You’ll get to see more of that treat I believe he is installing 1 ton axles and stretching right now so maybe by next summer it’ll be out.
@cvenable3283 Жыл бұрын
I’m wanting to do a 5.0 in my cj5 what flywheel and pilot bushing and did he have to shorten the output shaft
@GabesGarage
Жыл бұрын
+C Venable he used a stock flywheel and clutch assembly fo a early 90s f150. There are 2 options. A 10in and 11in., use the larger it has more surface area on the disk to support more torque. He don’t remember how much he cut off the input shaft but it wasn't much, maybe 3/8 of an inch. The clutch fork and rod took some modification but a competent car guy should be able to figure out where and what has to be modified.
@CJ7nvrstk5 ай бұрын
Looks like he needs lower gears and lockers.
@S1LV3RBACK1
Ай бұрын
Def lockers.. and a tiny bit wider stance.
@smokinjo75977 ай бұрын
I have a 79 cj-5 with a 258 6 cylinder and want to do the 5.0 swap, What bell housing is needed?
@GabesGarage
7 ай бұрын
He said he used the ford bell housing on factory 3 speed transmission
Пікірлер: 16
He got lucky he didn’t roll. Good save. Nice Cj.
Just saw the thumbnail and liked the video ♥️♥️.... I wonder why not this kinda content goes viral 🤔
@GabesGarage
Жыл бұрын
+Drift King I be asking my self that, there’s a lot that I still need to learn when it comes down to KZread. Thanks for the like 😁
Heck yeah Jake busted his butt to get the ole cj in prime running condition and that 302 sounds sooo good
@GabesGarage
Жыл бұрын
+bassment03 not bad at all for a first time after the swap. Nothing broke and it did everything he wanted to do.
My dad had one it dominated all the new jeeps on the trails was AMC V8
Great vid gabe 👏 👍
That is one badass CJ-5, sounds really good too! I have an '05 TJ Rocky Mtn 4.0L, and it is by far thee best and most fun vehicle I've ever had. I'd rather restore a '41 - '06 Jeep than get an '07 - present day heep. Jeep Born: 1941 Died: 2006 O|||||||O 🇺🇲 Only in a 2 Dr 🇺🇲 '41 - '06
@GabesGarage
9 ай бұрын
You’ll get to see more of that treat I believe he is installing 1 ton axles and stretching right now so maybe by next summer it’ll be out.
I’m wanting to do a 5.0 in my cj5 what flywheel and pilot bushing and did he have to shorten the output shaft
@GabesGarage
Жыл бұрын
+C Venable he used a stock flywheel and clutch assembly fo a early 90s f150. There are 2 options. A 10in and 11in., use the larger it has more surface area on the disk to support more torque. He don’t remember how much he cut off the input shaft but it wasn't much, maybe 3/8 of an inch. The clutch fork and rod took some modification but a competent car guy should be able to figure out where and what has to be modified.
Looks like he needs lower gears and lockers.
@S1LV3RBACK1
Ай бұрын
Def lockers.. and a tiny bit wider stance.
I have a 79 cj-5 with a 258 6 cylinder and want to do the 5.0 swap, What bell housing is needed?
@GabesGarage
7 ай бұрын
He said he used the ford bell housing on factory 3 speed transmission
Estuvo cerca jaja