Testing 3 different auger tips on clay
Тәжірибелік нұсқаулар және стиль
In this video I want show the results after testing three different end tips on an auger when drilling on clay. It has been very frustrating getting the auger stuck so often but I finally got to the right tip at the end of the auger to drill successfully.
LINKS
None Affiliate link
Fish tail tip tested in the video. www.ebay.com/itm/134113891526
Affiliate link
Another tip that I believe would work great on clay: amzn.to/3BTv0uh
OTHER VIDEOS
Check out my other Massey Ferguson videos
Power Steering pump overhaul: • Massey Ferguson 231 Po...
Power Steering cylinders rebuild: • Massey Ferguson 231 po...
Massey Ferguson Maintenance: • Massey Ferguson 231 co...
MUSIC
I use Artlist for all my music. If you are looking for a music provider for video production I highly recommend Artlist. Click this link to learn more: artlist.io/ButteWorks-1617610
SOCIAL MEDIA & CONTACT
KZread Channel: / butteworks
Instagram: / butteworks
Contact Info:
email: butteworks@gmail.com
Пікірлер: 18
It’s best to drill about eight inches and pull it out, eight more and pull it out. Go slow and drill a little then clear the hole, that way you don’t get stuck. Yeah I learned the hard way.
@BUTTEWORKS
2 ай бұрын
Agree, it is a hard learning curve until you realize that is the way. until you figure out, lot of pipe wrench and cheater bar trying to get it out.
Best advice I've gotten in a long time.... Worked exactly the same way for me and saved a ton of work and frustration... Thanks for sharing this, Butteworks
@BUTTEWORKS
10 ай бұрын
I’m glad it was helpful to you. Thank you for your comment.
Excellent video and great advice. Thanks for sharing.
@BUTTEWORKS
7 ай бұрын
Thank you, I’m glad you found it useful.
Excellent video, thanks for the info.
@BUTTEWORKS
10 ай бұрын
Thank you, I’m glad you found it useful.
One of the best things you can do if you plan to dig a lot of holes with a tractor, besides getting a FEL mounted auger, is to have the remotes match on both the 3PH and auger. m &m on one, f&f on the other so you can easily reverse the flow and back the auger out if it gets stuck in clay or on a root. But if you have enough GPM hydraulic flow, a FEL auger can't be beat. You can see what you're doing, apply downward pressure, and reverse rotation on the fly.
@BUTTEWORKS
8 ай бұрын
Agree, hydraulic would be the way to go. In my case the half cut tip is working very well. So far I have made 50+ holes and does not get stuck. In any case this is a 600USD auger, so it is what it is. A bit wobbly, not too curate but for what I do it serves me well.
Very ingenious thank you for sharing
@BUTTEWORKS
Жыл бұрын
You are so welcome!
I built a stop that rest on the ground at 2 feet so when it starts to bury all it does is stops and then it spins and strips the hole out
@BUTTEWORKS
11 ай бұрын
I tried something like that at first but I could not strip the hole, instead I snapped the sheer pin on the auger. Hard clay is tough. Thank you for checking the video.
@texastrucksforus9905
10 ай бұрын
@@BUTTEWORKS yes sir and that’s no joke that clay is no joke we are primarily Rock in my location
Thank you!
@BUTTEWORKS
Жыл бұрын
You welcome. Hope it helped.
@chris259charter
Жыл бұрын
@@BUTTEWORKS I have a deck job with clay soil. You're should be very helpful information.