Tachometer Hack
Describes how to add an alligator clip to a small engine tachometer to allow quick attachment and disconnection. Transforms the tachometer to a mobile test instrument for small engine repair and adjustment.
Describes how to add an alligator clip to a small engine tachometer to allow quick attachment and disconnection. Transforms the tachometer to a mobile test instrument for small engine repair and adjustment.
Пікірлер: 55
Awesome and very simple. I use the tachometer at time but not regularity and was about to buy a $60+ unit when I stumbled into your post. It saved me😀 some much needed $$ . Thanks for sharing this idea!!
So today it was 40 outside so I could try this hack on the tach I purchased and it worked just fine. Thanks for this great Hack !!!!
Thank you for sharing this absolutely clever idea! After watching your video I ordered a battery clip from Amazon and installed it on the tachometer/hour meter I received a few days earlier. It was easy to do and works like a champ! I was surprised that the electromagnetic field was strong enough to trigger the device (with essentially what amounts to one turn of wire) but it certainly is! The ability to be portable is a big plus. Best wishes for your continued success here on KZread.
This is great just got mine yesterday and glad I found your channel thanks.
I put the clip on today and it worked fine, you just have to position it close to the hinge, it works just as good as wrapping it around 5 times and then taping it in place.
Hooked one up to my 4010 Mule and it worked great!
Yes. I am furious I did not think of that. Seriously. Brilliant. Thank you sir! 9.10.2023
Brilliant, why didn't I think of this myself? Thanks for the hack
Dude that's great! IDK why I didn't think of that! Thank you!
Great idea! I'll be doing this for sure.
Good stuff 👏 another great mind thinking outside the square.. I'm not alone.. 👍
Thank you for the new idea.
great video
Great little mod, thanks.
Neat! Thanks for sharing.
Can you extend the length of the inductor wire?
I know you're mad you didn't think of it yourself..Thats hilarious 😂 Thanks subbed
thank you that was helpful.
Another good way is to wrap the wire around good and tight, then put a zip tie around running and standing ends to keep it all tight.
Thank you
I need to get a clamp. I agree its a PITA to wrap. I was just always wondering how it would work since they say too many or too few wraps no good. How many wraps is a clamp equal to? According to the consensus here it works fine so I guess its a moot point.
Great idea! Anyone questioning the accuracy has to wonder about the accuracy of the inductive tach to begin with. Using this on a 4 cylinder engine, is any conversion needed when it reads only a single cylinder?
I have just ordered a different model with a ground wire. Do I have to connect ground wire or will it still work. Don't really want to loosen bolt on motor to connect it as is a new motor and might void warranty if anything happens to it. Cheers.
brilliant
does this tach have a setting for 4 stroke and 2 stroke?
My clips are coming today from Amazon, wrapping that wire around is a pain, I hope it works out for me, thanks!
@johnmorse8434
Жыл бұрын
Did it it works
@johnmorse8434
Жыл бұрын
kzread.infoEn7-iN8gwnU?feature=share
@browngreen933
11 ай бұрын
Awesome. I'm doing this!
I tried this and it didn’t work. My tach has an s1 and s2 instead of an M and S. What am I doing wrong?
This is exactly what I was looking for. It was hard to hear you when you talked about cutting the wire. How long did you leave the wire?
@PSN7373
2 жыл бұрын
Dont cut the wire
Hot to put settings in 4 stroke
Who sells those clops or where did you purchase it?
mice hack. wasn't sure if you could test with these and only do 1 or 2 loops around the spark wire. what I wanna do is buy 2 of these and check 2 plug/cylinder engines. then swap them and see if the readings are the same. could tell me if a plug is fouled or ignition coil is bad. ie running on 1 cylender or week cylender. rough running engine.
How you reset these
Top
No way that’s accurate! 🤷🏼♂️
@frankconly6736
Жыл бұрын
Why not? No different than an inductive timing light
@stradplayer90
Ай бұрын
I agree. If the metal clip is completing the loop like the wrapped wire, then it shouod work. @frankconly6736
I purchased one of these for my Husqvarna 128 LD weedeater. The manual says the idle rpm's are between 2800-3200, so I have the rpm's set to 3,000, but the max speed be set to 11,000 rpm's. My question is, how would I get this techometer to show 11,000 rpm's?
@pitapitabread
25 күн бұрын
have you set the mode '1' for two revolutions per one ignition spark, or to mode '2' for one revolution per one ignition spark?
@Thomas-nz4uh
25 күн бұрын
@@pitapitabread Thank you for responding, but yes I've set it at 1,2 and 3 modes with the same results. The manual says the digits range from 0-30,0000 but I can't get it to go above 9999.
@Thomas-nz4uh
10 күн бұрын
@@pitapitabread Yes, I went through all the settings the first time, but I finally figured it out and got 11,000 rpm's but that was to high which is required in the manual. At 11,000 rpm's my high adjustment screw was almost seated, so I backed it down to 9,000 rpm's and I'm comfortable with that. Thanks for taking the time to share the video and responding though.
@TEEZS10
8 күн бұрын
@@Thomas-nz4uhhow were you able to get the higher readings?
@Thomas-nz4uh
7 күн бұрын
@@TEEZS10 Set the tachometer to number 2 for my two stroke weedeater, then turning the high screw clock wise at full throttle.
When using near a lawnmower keep it well away from the mower skirt, trust me lmfao. Should be fine to just clamp the wire in the clip keepers without what you've done unless there's a specific reason. My tach is a different model/make however it works on the same principle & doesn't need to be threaded/looped with the clip. The downside with mine is assuming the battery is ok, it requires me to touch the looped connection at the meter for it to read correctly i.e the exposed wire at the end of the insulation, why's that ? damned if i know it's been like that since new,even sent the first one back until by accident i found how to make it work. It wasn't a cheap meter either grrr
What amp clip does a person use?
@scorpnz4433
7 ай бұрын
As small as you like will be fine. The one he uses is in reality overkill however so long as it works who cares
@davidsmit1074
7 ай бұрын
@@scorpnz4433 thanks for that.
I just use a rubberband 😊
@hparadigma
4 ай бұрын
How do you use it?
@kevinclear4007
4 ай бұрын
@@hparadigma you use a rubberband to hold the wire in place. What you mean how you use it?
@hparadigma
4 ай бұрын
@@kevinclear4007 wellnoted. I thought you are using some method that make it easier to attach and deattach the wire. 🙏