TA-0395: Fluke Philips PM2812 Power Supply - Test , Repair and Calibration
Ғылым және технология
Blind buy, Lets see whats going on, go step by step, not to kill it.
Calibration around 22:00
Fluke Friday Videos:
FlukeFriday (E1) 7-600,1ACII : • TA-0316: Fluke Friday ...
FlukeFriday (E2) 10,11,12 : • TA-0317: Fluke Friday ...
FlukeFriday (E3) 12B : • TA-0320: Fluke Friday ...
FlukeFriday (E4) 25,27,8025B : • TA-0322: Fluke Friday ...
FlukeFriday (E5) 30,32 : • TA-0325: Fluke Friday ...
FlukeFriday (E6) 37 : • TA-0326: Fluke Friday ...
FlukeFriday (E7) 51, 62 Max: • TA-0328: Fluke Friday ...
FlukeFriday (E8) 21,23 70,73,75,77,79 : • TA-0329: Fluke Friday ...
FlukeFriday (E9) 87-III and 787 Processmeter : • TA-0331: Fluke Friday ...
FlukeFriday (E10) 97 and 92B-Serie II Scopemeter : • TA-0334: Fluke Friday ...
FlukeFriday (E11) 123 and 192 Scopemeter : • TA-0336: Fluke Friday ...
FlukeFriday (E12) 91 Seire II Scopemeter : • TA-0338: Fluke Friday ...
FlukeFriday (E13) 164T Multifunction Counter : • TA-0340: Fluke Friday ...
FlukeFriday (E14) 287 in the AN/GSM-437 Army Kit : • TA-0342: Fluke Friday ...
FlukeFriday (E15) 893A AC-DC Differential Voltmeter: • TA-0346: Fluke Friday ...
FlukeFriday (E16) 233 Multimeter Remote Display: • TA-0347: Fluke Friday ...
FlukeFriday (E17) 893A AC-DC Differential Voltmeter Part 2 : • TA-0348: Fluke Friday ...
FlukeFriday (E18) 867 and 867B Graphical Multimeter : • TA-0352: Fluke Friday ...
FlukeFriday (E19) 1900A and 7200A Series Frequency Counter : • TA-0360: Fluke Friday ...
FlukeFriday (E20) 81438 and 111 Special Multimeter : • TA-0374: Fluke Friday ...
FlukeFriday (E21) APPA 203, it could be a 38 Multimeter : • TA-0392: Fluke Friday ...
FlukeOlderVideo - 87 III 87 V Brymen BM857s BM869s : • #271 Fluke 87 III 87 V...
FlukeOlderVideo - 187 Calibration Procedure : • #251 Fluke 187 Calibra...
FlukeOlderVideo - 1900A Frequency Counter : • #114 Fluke 1900A Frequ...
FlukeOlderVideo - 1920A Frequency Counter : • #063 Fluke 1920A Frequ...
FlukeOlderVideo - PM2534 Bench Multimeter : • #098 Philips Fluke Mul...
FlukeOlderVideo - PM2812 Power Supply : • TA-0395: Fluke Philips...
FlukeOlderVideo - 5101B Calibrator First look : • #295 Fluke 5101B Fluke...
FlukeOlderVideo - PM6662 120 MHz Frequency Counter : • #035 Philips Fluke PM6...
FlukeOlderVideo - PM6685 RiFa Boom! : • #234 Fluke Philips PM6...
FlukeOlderVideo - PM6685 8GHz Frequency Counter : • #233 Fluke Philips PM6...
FlukeOlderVideo - 8000A 8010A Bench Multimeter : • #040 Fluke 8000A vs 80...
FlukeOlderVideo - 8024A Handheld Multimeter : • #102 Fluke 8024A DMM H...
FlukeOlderVideo - 8120A Bench Nixie Multimeter : • #094 Fluke 8120A Resto...
FlukeOlderVideo - 8125A MilSpec Nixie Multimeter : • #025 Fluke 8125A MilSp...
FlukeOlderVideo - 8200A Bench Nixie Multimeter : • #074 Fluke 8200A NIXIE...
FlukeOlderVideo - 8300A Lab Nixie Multimeter : • #143 Fluke 8300A NIXIE...
FlukeOlderVideo - 8500A Lab Multimeter : • #133 Fluke 8500A Resto...
FlukeOlderVideo - 8810A Bench Multimeter : • #149 Fluke 8810A Clean...
Related Items:
Fluke Fuse 11A: go.tonyalbus.com/Fluke11A
Fluke Fuse 440mA: go.tonyalbus.com/Fluke440A
Volt/Current Pro LB02A go.tonyalbus.com/LB02A_A
DMMcheckPlus go.tonyalbus.com/DMMcheckPlus
Volt/Cur FNIRSI SG003A go.tonyalbus.com/SG003A_Ali
Voltage/Current LB02G go.tonyalbus.com/LB02G_A
QuixxPlasicPolish go.tonyalbus.com/QuixxPlasicP...
PolyWatchPolish go.tonyalbus.com/PolyWatchPolish
LCR standard go.tonyalbus.com/LCRref_A
CR standard go.tonyalbus.com/CRref_Ali
BananaBanana go.tonyalbus.com/Banana4Banana4
BananaCrock go.tonyalbus.com/Banana4Crock
BananaBananaProtect go.tonyalbus.com/Banana4banan...
BananaPlug go.tonyalbus.com/Banana4Plug
DisplayFluke7,10,11,12,12B go.tonyalbus.com/DisplayFluke10
#PM2812 #Philips #Fluke
Пікірлер: 18
The over voltage warning could be due to AC ripple on the DC rail causing it to sense the AC peaks, either from the power supply board or the channel boards. I have seen something similar years ago on an HP power supply, AC ripple caused a voltage error.
@TonyAlbus
3 ай бұрын
Thanks Scott, yes that is indeed the direction i was also thinking, there is an AC pickup somewhere, it was also very sensitive during calibration, that failed when you just left an open wire in one of the outputs. it fail then also on OVP. after i received the AC filter i will also put some ferrite chokes around the output wires. i could have some HF going around in my shack too :)
@TheDefpom
3 ай бұрын
@@TonyAlbus because of its age I would re cap it, even if they test ok.
Excellent power supply, very stable indeed. I had a bench multimeter with a similar Schaffner filter that had blown up.
@TonyAlbus
3 ай бұрын
Yes those filter will go, on my frequency counter PM6685 is also went.
Nice power supply Tony. It has great lab work potential with its high specification. I would image back in the day that PSU would have been very advanced and used for high end design work. I particularly like the way you were able to carry out controlled testing with the electronic load and especially the variable AC supply which is very smart indeed. I also thought the way you added the switch with the IEC connectors looked really smart and makes very a safe solution when compared to just hard wiring it in. Ian
@TonyAlbus
3 ай бұрын
Thanks Ian, yes i thought using the AC powers source with current limiter was sort of the lightbulb in series for nowadays :) to savely test it step by step... yes proper device, i was amazed how easy it calibrated too.
Very nice looking power supply, Tony. Because it is a switch mode supply I would definitely try to find a replacement line filter. Your switch mod would still work with the original type and I agree that front panel power switches are a must. The display looks like it might have an ELP backlight, I've had some success replacing them with LEDs, it is a question of space (and how much it bothers you). Regards, David
@TonyAlbus
3 ай бұрын
Thank you David, yes the filter needs to be replaced, i agree. the backlight a maybe, depends if i am going to use it or sell it.
- A very large power supply, but only 120 watts of power... - The technologies of those times probably did not allow us to do more..
@TonyAlbus
3 ай бұрын
Yes agree, but also on higher power you maybe do not need such high precision and still it does 10 Amps.
I agree with Defpom on replacing the caps, as maintenance. Also, to replace the battery, as maintenance. As you have it wired, the switch VAC wire is in the same compartment as the sense wire and, as you say, this may create the sensing problem. So, I wonder if you might find a way to put the new line filter on the incoming line of the switch... Instead of its original position, which would be after the switch path. This way, the switch line inside the sense compartment would be filtered. I imagine that in-line filters are manufactured and, if so, such might be easier to mount. Cheers.
@t1d100
3 ай бұрын
You might also do a visual inspection of the regulator boards...
@TonyAlbus
3 ай бұрын
Thanks, yes good points !
🙂👍👍👍👍👍👍👍👍
@TonyAlbus
3 ай бұрын
Thank you!