Very specific and right to the point of the problem for diagnosing flex plate. Awesome illustration! Thank you for your video.

My starter grinds at startup, I have a transmission going bad and after watching this video I think I need a new flex plate. 💸💸💸

Excellent video Top 5 Auto Repair. Well explained.

You are an excellent teacher.

Could it also make a metal card flapping sound? Like when people would put a playing card in their tires on the bicycles? Mine is more prominent in yhe front, driver's side. And we just got a rebuilt transmission for my 2001 GMC Yukon 1500. It happens while I'm driving, regardless if I'm accelerating to go, or cruising the freeway, or uphill and downhill. The sound comes intermittently and goes away. It doesn't stay permanently. My RPM is around, 2 - 2.5 as well.

Great video, was interesting and very helpful

Thanks for sharing ☮️Houston Texas

It would be great if you also made us hear the sound of the part while damaged as well. Not many persons understand the vehicles specifics

I had a 1996 Toyota t100 & at around 280,00 miles the flex plate cracked. Then within a year it cracked again. Then the third flex plate cracked. The garage could not figure out why so I had to get rid of it. The motor was awesome & never burned a drop of oil. Very depressing.

@TrySomeFentanylToday

4 ай бұрын

Probably a bad torque converter.

@excalibur_lvxii1392

3 ай бұрын

Mechanics kinda look straight at the issue and not around it in my experience. That's why I do work on my car myself as long as it's not taking an entire engine apart. If I were working on your car back then I would have looked at everything possible. I haven't ever touched a transmission besides the outer filter and lines but years ago with GM 3.8L engines the bolts patterns and dowel pins were drilled improperly, causing cracked and broken flywheels left an right. And with cracked flywheels it's a hit or miss. You can go years with a cracked flywheel (not recommend if you know it's crack. If you know there's an issue with internals of engines/transmission get it fixed ASAP) but if there's an issue with alignment it'll always crack. It's inevitable. There's also the crankshaft itself which was most likely your issue. If the crankshaft flange is worn it'll also cause this. Its a major possibility with having a worn down over 200,000 mile engine. If this was the case you got rid of a whole world of shit show that was to come. Another issue is the engine and transmission mounts. If the engine/transmission are moving up, down and all around from worn out mount bushings that messes with the alignment which causes the inevitable demise of the flexplate unfortunately. The rarest case I've heard of was the hardware was worn down so the mounts bolts slowly loosened and caused a crack.

Great video man

Its weird, I have a 2017 f150 5.0 and has a knocking sound when I put it in drive but goes away when I put it in neutral. Wondering if this could be it. Guess I know what I'll be inspecting in the morning

My 2006 Chevy Silverado 1500 6.0, all you described it's what my truck is sounding like. And one of my mechanic check it and he said all you said, that needs to get replaced this part. And other mechanic said engine needs to be change. But i know it has to be this. Like this comment or comment for and Update. Imma get it fix one of these days

If you ever do an engine swap on any GM V6 fwd, make sure that dowel pin is there or the center will rip away

Thanks for sharing Jamaica

Thank you very informative

Does this also effect the acceleration? My 09 f150 does not take off right away it shakes and stalls before going lmk.

Great video. New sub

good info!

Lovely

Can someone help me I need to find a flex plate for my 2004 Mitsubishi lancer Ralliart 2.4L what’s a good website for flex plates Thanks

Any idea about this issue on my 2004 Impreza wagon manual, 156,000 miles? Clutch replaced 20,000 miles ago. Center Differential replaced 200 miles ago. Noise started after center diff replacement, about 100 miles later. Does not make noise in turns (except when coasting). A mild clicking/tapping noise (sounds soft like playing card in bike spoke) is present when coasting in any gear, front main transaxle area (transmission). It varies in frequency and speed, according to the output shaft RPMs, and sometimes it's quieter or not there at all. It's probably a small piece of flat wire from a piece of seal that got away during clutch or center differential replacement. Doesn't seem to affect operations though. Does it about 80% of the time, but is not noticeable 50% of that time. It's quiet enough where talking, dirt roads, road noise, or any stereo masks it. Doesn't make the noise when it's under load...as in forward or reverse gears in play, clutch released. Any ideas, other than debris in case? Thanks!

@HarleySLA

Ай бұрын

Have you checked to make sure your driveline isn't bound up and everything is properly greased (splines and joints)

My 1997 4runner makes a noise when @ idle in drive at a red light, then when i take off the noise goes away some we swapped transmission on my v6 3.4 6 months ago, and im praying it was just loose bolts that need tightening god i pray its just loose i dont wanna have to pull the transmission again.

Gearbox automatic focua mk2 2.0 .The sounds can only be heard when it is cold, below +2 degrees C. The starter was replaced with a new, non-original one when it was warm outside, so I don't know if I fixed the problem at that time. Half a year later, in winter, the sounds are heard again The sounds can only be heard when it is cold, below +2 degrees C. The starter was replaced with a new one when it was warm outside, so I don't know if I fixed the problem at that time. Half a year later, in winter, the sounds are heard again What do you think about this sound? What needs to be replaced or what can be checked to be 100% sure that everything is working after repair?

@ha48124

6 ай бұрын

Sometimes it takes a long time to start or starts the second time

Only 3 converter to flex plate bolts on many Gm SUV type vehicles. Not a problem as far as I know.

U can remove flexplate by sliding transmission back 8 to 10 inches and remove the flex plate cuts the job down to 1 hr this is what shop do to screw people over and charge them 4 hr labor for a 1 hr job

If this flexplate is broken and misaligned, would the starter also need to be replaced?

@desire_002

8 ай бұрын

Not necessarily but you should replace it if the flex plate was fubar

What if it won’t start, even after a new starter?

I have a bell noise like a piece broke off and it is rattling in bottom of bell housing.

@tjonesauto

5 ай бұрын

It's likely rubbing. Spray some WD 40 up in there while running. If it goes away it's bent from wobble. If not there may be a loose bolt to the torque converter

@tjonesauto

5 ай бұрын

...I experienced that on a Navigator

😊👍

Removed engine assembly due to blown head gasket, after the job done, engine sound changed and flexplate broke within days. Bought new flexplate and after a week broke again. Mechanic then noticed that one dowel pin is missing , after both dowels installed , engine sound changed and car fixed.

@tjonesauto

5 ай бұрын

Same here on a 1998 Monte Carlo 3.1. the center ripped away.

I have a automatic 2008 lancer gts and it has broke 3 flexplates its a headache

@HardCoreGym123

6 ай бұрын

Must be misalignment. I had the same issue with my car. Check 2 dowel pins when you couple tranny and crank side

I had a bad flex plate at around 45-50 mpg I got vibration.

@panteraklan681

8 ай бұрын

I having that issue plus a metal noise as well sounds like I got homework to do

@jayt717

2 ай бұрын

@@panteraklan681Ever figure it out?

@panteraklan681

Ай бұрын

@@jayt717yeah it was that so I change it with a heavy duty one

@jayt717

24 күн бұрын

@@panteraklan681 Mine turned out to be the rear u-joint.