Replacement details. Vehicle has 310,000 Kms on the original bearing.
Жүктеу.....
Пікірлер: 40
@ignatius22302 жыл бұрын
And never, no matter how tempting it is, DONT try to clean a magnetic ring with another magnet to clean rust or metal debris because you are going to erase the magnetism printed strips of it. I know this because its on my shameful list of things I did wrong, when you go for a drive test after finishing the replace of a brand new bearing & hub kit the ABS/ESP fault light comes ON at the same time you remember that "Directed by Robert B. Weide" song
@TheGibby3340
2 жыл бұрын
Very good point. Mistakes (although at times extremely frustrating/costly) are part of the learning process. I have made countless mistakes over the decades and will continue to do so…We are human. Thx for watching 👍
@iansworkshop2 жыл бұрын
Brilliant job and video Ian , one of those jobs you dread to start , but very satisfying when finished , cheers 👍
@TheGibby3340
2 жыл бұрын
Cheers Ian 👍
@theGADGETSplaylist2 жыл бұрын
I like that small press and that slide hammer. well done Ian!
@TheGibby3340
2 жыл бұрын
They have came in handy over the years . They sit doing nothing for very long stretches, but when you need them…Cheers Denis 👍
@albertnel7468 Жыл бұрын
Thank you for the info on the magnetic side of bearing!
@TheGibby3340
Жыл бұрын
Thx for watching. Cheers 👍
@bleebleblahble88332 жыл бұрын
Need to do this on the fiesta at some point alongside front axle seals. Thanks for making it seem manageable.
@TheGibby3340
2 жыл бұрын
Thx for watching 👍
@mechanicmatt8712 жыл бұрын
Good job mate , great video 👍
@TheGibby3340
2 жыл бұрын
Cheers Matt 👍
@winrampen1174 Жыл бұрын
Many thanks for your extremely helpful video. Although I'm from Oakville, Ontario - I'm writing from Scotland - where I've just succeeded in changing my front wheel bearing. Your help travels far and wide! Two points which may be useful: 1. I was having trouble with the track rod end nut (actually the rusty cotterpin) and ended up undoing the track rod - which is less likely to be seized - though you need to ensure that you don't alter the nut position. and 2. I used a bit of 12mm studding with mudguard washers to hold the hub upside down in my drill press. Going at low speed (100 RPM-ish) I played a torch on the bearing inner, which got to about blue heat and then dropped off. Very easy if you have a torch.
@TheGibby3340
Жыл бұрын
Just saw yer comment. I was watching the old firm match 😁. Thx for the kind words. Some good tips. What took you to Scotland if you don’t mind me asking?
@winrampen1174
Жыл бұрын
@@TheGibby3340 I came here 45 years ago to work on renewable energy at the University of Edinburgh - which I thought might last two years........ Two companies, one wife, three children, multiple grandchildren later and I'm still here. Much more mountainous than Ontario, and very few shopping malls - what's not to like!
@TheGibby3340
Жыл бұрын
@@winrampen1174 Nice. I’ve been in Canada for 48 years now. So far more Canadian than Scottish, truth be told. I’m glad Scotland didn’t disappoint. 🍻
@stephanhughes8164 Жыл бұрын
Fantastic content, thank you!!
@TheGibby3340
Жыл бұрын
Thank you Sir and Thx for watching 🍻
@didiercollot4282 ай бұрын
Merci pour le tuto👍
@TheGibby3340
2 ай бұрын
De rien et merci d'avoir regardé 🍻
@CarsExposed2 жыл бұрын
Nicely done mate good for another 200k 😉👍
@TheGibby3340
2 жыл бұрын
Thx Igor 👍
@Automotive_Solutions2 жыл бұрын
Top job. I must admit I prefer your commentry to the silent movie version 😅.
@TheGibby3340
2 жыл бұрын
Cheers Iain. Think I had my little press near its limits 🤣
@JohnnysSpeedShop2 жыл бұрын
Nice work mate...job well done and I'm sure no more rumble 🤣🤣
@TheGibby3340
2 жыл бұрын
Cheers Johnny 👍
@GoldenSim272 жыл бұрын
Thank you sir
@TheGibby3340
2 жыл бұрын
Thx for watching. Cheers 👍
@zb706010 ай бұрын
How long did you leave the bearing and hub in the freezer to shrink it?
@TheGibby3340
10 ай бұрын
Nothing too scientific about it. Think I threw it in the previous night. Thx for watching 🍻
@joanieolson74272 жыл бұрын
Could you let me know where I can get the circlips for the front bearings?
@TheGibby3340
2 жыл бұрын
They were purchased from Suzuki. If you live in Canada or the States, google Suzuki authorized dealer and you can still obtain SGP locally.
@joanieolson7427
2 жыл бұрын
@@TheGibby3340 Thanks very much. I'll have my parts next week. (I live in Ottawa)
@avenfisher97956 ай бұрын
What year SX4 is this?
@TheGibby3340
6 ай бұрын
2007-2009’ Thx for watching 🍻
@shadowopsairman15834 ай бұрын
What year and specific sx 4?
@TheGibby3340
4 ай бұрын
2007-2009’ 2L gasoline, hatch.
@Dreadmyshadow Жыл бұрын
That sure looks like a southern car to me
@TheGibby3340
Жыл бұрын
It is a “southern” car. Southern Ontario Canada 😃
@Dreadmyshadow
Жыл бұрын
Lol lucky here in CNY that thing would be a rusted mess
Пікірлер: 40
And never, no matter how tempting it is, DONT try to clean a magnetic ring with another magnet to clean rust or metal debris because you are going to erase the magnetism printed strips of it. I know this because its on my shameful list of things I did wrong, when you go for a drive test after finishing the replace of a brand new bearing & hub kit the ABS/ESP fault light comes ON at the same time you remember that "Directed by Robert B. Weide" song
@TheGibby3340
2 жыл бұрын
Very good point. Mistakes (although at times extremely frustrating/costly) are part of the learning process. I have made countless mistakes over the decades and will continue to do so…We are human. Thx for watching 👍
Brilliant job and video Ian , one of those jobs you dread to start , but very satisfying when finished , cheers 👍
@TheGibby3340
2 жыл бұрын
Cheers Ian 👍
I like that small press and that slide hammer. well done Ian!
@TheGibby3340
2 жыл бұрын
They have came in handy over the years . They sit doing nothing for very long stretches, but when you need them…Cheers Denis 👍
Thank you for the info on the magnetic side of bearing!
@TheGibby3340
Жыл бұрын
Thx for watching. Cheers 👍
Need to do this on the fiesta at some point alongside front axle seals. Thanks for making it seem manageable.
@TheGibby3340
2 жыл бұрын
Thx for watching 👍
Good job mate , great video 👍
@TheGibby3340
2 жыл бұрын
Cheers Matt 👍
Many thanks for your extremely helpful video. Although I'm from Oakville, Ontario - I'm writing from Scotland - where I've just succeeded in changing my front wheel bearing. Your help travels far and wide! Two points which may be useful: 1. I was having trouble with the track rod end nut (actually the rusty cotterpin) and ended up undoing the track rod - which is less likely to be seized - though you need to ensure that you don't alter the nut position. and 2. I used a bit of 12mm studding with mudguard washers to hold the hub upside down in my drill press. Going at low speed (100 RPM-ish) I played a torch on the bearing inner, which got to about blue heat and then dropped off. Very easy if you have a torch.
@TheGibby3340
Жыл бұрын
Just saw yer comment. I was watching the old firm match 😁. Thx for the kind words. Some good tips. What took you to Scotland if you don’t mind me asking?
@winrampen1174
Жыл бұрын
@@TheGibby3340 I came here 45 years ago to work on renewable energy at the University of Edinburgh - which I thought might last two years........ Two companies, one wife, three children, multiple grandchildren later and I'm still here. Much more mountainous than Ontario, and very few shopping malls - what's not to like!
@TheGibby3340
Жыл бұрын
@@winrampen1174 Nice. I’ve been in Canada for 48 years now. So far more Canadian than Scottish, truth be told. I’m glad Scotland didn’t disappoint. 🍻
Fantastic content, thank you!!
@TheGibby3340
Жыл бұрын
Thank you Sir and Thx for watching 🍻
Merci pour le tuto👍
@TheGibby3340
2 ай бұрын
De rien et merci d'avoir regardé 🍻
Nicely done mate good for another 200k 😉👍
@TheGibby3340
2 жыл бұрын
Thx Igor 👍
Top job. I must admit I prefer your commentry to the silent movie version 😅.
@TheGibby3340
2 жыл бұрын
Cheers Iain. Think I had my little press near its limits 🤣
Nice work mate...job well done and I'm sure no more rumble 🤣🤣
@TheGibby3340
2 жыл бұрын
Cheers Johnny 👍
Thank you sir
@TheGibby3340
2 жыл бұрын
Thx for watching. Cheers 👍
How long did you leave the bearing and hub in the freezer to shrink it?
@TheGibby3340
10 ай бұрын
Nothing too scientific about it. Think I threw it in the previous night. Thx for watching 🍻
Could you let me know where I can get the circlips for the front bearings?
@TheGibby3340
2 жыл бұрын
They were purchased from Suzuki. If you live in Canada or the States, google Suzuki authorized dealer and you can still obtain SGP locally.
@joanieolson7427
2 жыл бұрын
@@TheGibby3340 Thanks very much. I'll have my parts next week. (I live in Ottawa)
What year SX4 is this?
@TheGibby3340
6 ай бұрын
2007-2009’ Thx for watching 🍻
What year and specific sx 4?
@TheGibby3340
4 ай бұрын
2007-2009’ 2L gasoline, hatch.
That sure looks like a southern car to me
@TheGibby3340
Жыл бұрын
It is a “southern” car. Southern Ontario Canada 😃
@Dreadmyshadow
Жыл бұрын
Lol lucky here in CNY that thing would be a rusted mess