Suzuki 150 marine outboard spark plug change.
In this video you will see how to change a spark plug on a Suzuki 150 marine outboard motor. The difficulties of the task will be talked about and a work around will be demonstrated.
Spark plug Replacement Procedure.
Tools need
1.Ratchet
2. 5/16 head
3. spark plug head
4. Long extension
The first step is removing the hood. Step 2 pop up and off the plastic cover over the aft spark plug. Then place it upside down to be used to store screws. Proceed to take the first screw off the the spark plug sensor with 5/16th head. Next pull up and remove the sensor plug to get at the spark plug. Use the spark plug head on the ratchet to remove the old spark plug. Now with the tips of your finger place the new spark plug in the bottom of the slot gently to as to not damage it. To screw the new spark plug in lightly place the ratchet on the top of the plug and turn. ( if ratchet heads disconnect tighten from a half connection.) Continue to turn until hand tight then turn ¼ turn with the ratchet. The sensor for the spark plug can then be reinserted. After it is back in the hole re-secure it with the 5/16 ratchet.
Repeat for every remaining spark plug.
Average time to complete this task per engine is 30 minutes. There are 4 spark plugs total on a engine.
Пікірлер: 22
Just tape your socket to the extension and it will not fall off when screwing in the spark plug. Thanks for sharing the video 👍
Excellent video...just what I needed to change plugs in my 2006 150 hp Suzuki 4-stroke / 4-cylinder. From the internal cover to dealing with a socket stuck within the socket this video was invaluable. THANK YOU!
That “sensor” is the coil pack, you can also tape the socket to the extension to keep your issues from happening. Thanks for the video
@spoonfishing
4 жыл бұрын
^^Someone knows his way around a shop with tools. That's what I'm gonna do after the season.
@DanielWasserott
2 жыл бұрын
That's a good suggestion.
Good idea about the tape. If you haven't used tape and the extension comes loose from the socket try putting a piece of nitrile glove over the end of the extension and plugging it back into the socket. Used the glove trick many times to hold socket head screws to an allen wrench.
Excellent video...just what I needed to change plugs in my zuke 175hp
Thanks man. Looked at this todat
You can get a spark plug wrench attached to an a extender and never have to worry about it again
Now I know why my Suzuki dealer charges $300 for yearly service. LOL
Tilt the outboard in a vertical position instead of horizontal where gravity takes over
@DanielWasserott
2 жыл бұрын
I wish my over worked self thought of that then, good tip.
Plug you took out was fine, as far as I could tell. Just needed a light clean. You didn’t set the spark gap, unless you’d done that before but looked like to just put ne plug straigh in.
@DanielWasserott
5 жыл бұрын
Actually i did set the gap before hand yet i did forget to mention it in the video. Thank you for pointing out that.
@dylansmith631
5 жыл бұрын
Who gives a fuck joe brown you keypad expert that plug was old and fucked .... just give it clean and don’t forget to gap fucking dick head
@dylansmith631
5 жыл бұрын
Joe Brown moron
@benharrell1664
4 жыл бұрын
@@DanielWasserott What is the correct gap?
Those are not Sensors, they’re Coils.
@DanielWasserott
2 жыл бұрын
Thank you for pointing out my untrained ignorance. I am happy the people who watch and then see your comment will be educated as well, if they dont know and need to know in their situation.
four sensors would do for explanation not four f$$king sensors.
@DanielWasserott
2 жыл бұрын
America is a grand place. Sometimes a volley ball cut in the shape of a gasket will do yet also getting the gasket from the store does too. Life and all its spices are allowed here. Maybe the subtext is muddled.
Suzuki just can't make anything simple..