I think having bright turn signals is important, especially since I ACTUALLY use my turn signals.

@davixastro8765

4 ай бұрын

It’s very important

I bought led turn signal as well but if u let it on for too long like i got stuck in a really long turn and it started hyperflashinv after a while and i had to turn it off

2001 C5 Corvette. i replaced the front bulbs with LED's because the heat was melting the housings. After replacing all four rear 3056's w/ LED's, I got hyperflash. I installed the relay and all is well except... When the tail lights are on the brake lights work fine, yet when I use the turn signals the rears light up but don't flash and the fronts do!?? Ideas?

Did you end up needing load resistors for the rears?

Nicely explained good job!!!😊 I may go for rear one coz of highway lane change issue. Thanks for uploading such informative vid.

@Shinegadget

Жыл бұрын

Most welcome 😊

Those look great, I will order a set for my 2021 Pilot. Great review 👍🏽

@mrguzzi

3 жыл бұрын

Check my post above.

@dropdabeat442

Жыл бұрын

​@@mrguzzi i couldn't find your post. what is that about?

Do you think this hyperflashes if front and back are installed because its the car? Or u think its the same with toyotas?

I want the turn signals but in the bright white led with the built in resistor to prevent hyper flash. Do you know where I can find that.? For my 02 Accord

Great review !

@Shinegadget

3 жыл бұрын

Thanks 👍

Which one of the links you have added fits to Toyota Prius 2011?

I have a 2000 Toyota Camry LE 4 cylinder. I bought Sylvania Zevo Super bright leds turn signals. I put one in on the drivers side it hyper flashed so bad that it looked like it was staying on. So instead of getting resistors because I didn't want to cut the wiring I bought a Novita Flasher part number EP35. I had it put in where the original Toyota Camry Flasher was. The flasher works with both regular bulbs and led bulbs. So far I've had no problems. I just thought I would suggest this to you. All my led bulbs are Sylvania Zevo Super bright Leds except my headlight bulbs they are Oracle Lighting V Series with no fan and street legal they say. At least I hope they are. Haven't done the dashboard, glove box, console, and A/C lights yet but will. I'm very happy with the leds.

@basikfades

2 жыл бұрын

did your hazard lights blink out of sync wit the LED flasher relay?

Those LEDs are super extremely bright! have them on my 2020 Corolla !!they’re super lit 🔥!

@anakinandy

3 жыл бұрын

I got some too! I think they are too bright. I feel bad using them at night

@jc-diaz487

3 жыл бұрын

@@anakinandy lol same here bro.

@toyotabrony

Жыл бұрын

Nah lol. They are worth it

If you buy specific non running built in canbus for the back will not hyperflash. You can't have a runnig light on the back if it is built in canbus too.

Hey great videos ! I was wondering what kind of LEDs are you running for low beams on your corolla ?

@Shinegadget

3 жыл бұрын

The Low beams are already LED on the corolla SE. Thanks 👍

@LEGEND04131

2 жыл бұрын

You can get 6,000K color from lasfit too, they work extremely well, specially if your headlights have projectors they look like factory.

if you replace your front and rear turn signals with LEDs and your car is not wired for LED voltage, it will hyperflash.. you can only replace front OR rear with canbus LEDs

Excellent video presentation, I love it and learn a lot how to change lights. I am the man who always looking the car sharp and great, especially when I buy new car and switch to LED lights from interior and exterior. OK, now I am little confuse here. First of all, let me tell you I had just bought 2017 Hondo Pilot EX-L, which I guess same as just as yours. Before I buy those sets, can you please tell me which one I should buy for my 2017 Pilot EX-L. Should I buy LASFIT LED 7440 (Turn Signal Amber) OR should I buy LASFIT LED 7443 (Turn Signal + Running light Amber). For my knowledge I don't think so I have Running light on back rear side. I do have front but not on back rear side. So please tell me which set should I buy. Your help is appreciated. Rick

@Shinegadget

11 ай бұрын

Yes, 7440 will work good for the turn signals on the Honda Pilot. Let me know if this answered your question. Thanks for watching

Do you still have your trunk led turn signal strip installed on your Corolla?

@Shinegadget

3 жыл бұрын

yes 👍

Which set did you put, the rear or the front? I was thinking to do the front but the back looks good too! What happens if I put both in the front and the rear and it does not hyperflash? Can it damage my vehicle ?

@Shinegadget

3 жыл бұрын

On the rear turn signals only. 👍

@Shinegadget

3 жыл бұрын

It won't damage the car. it's just a safety feature that tell you that a bulb is burn out 👍

@kelm1123

3 жыл бұрын

I installed mine in the back, they look great. Want to put the fronts but don't want to put resistors.

When you got the hyper flash and took off the led bulb and put back the stock one does the hyper flash still occur ?

@Shinegadget

3 жыл бұрын

No It won’t hyper flash with oem bulbs 👍

@toyotabrony

Жыл бұрын

U don’t need to take them off when they get hyperflash. When they do, simply turn the turn signal lights off. For around 1-2 minutes and ur good to go. They cool off

My only question is, in the beginning of the video he said his lights were a 7440 single not the 7443 dual but at around the 4:06 mark of the video if you pay attention to the bulb it clearly shows 2 connectors on each side of the bulb. So which bulb is installed the 7443 or the 7440? I have 7443s on my car and I don't want o just waste money on something that isn't going to work.

@Shinegadget

2 жыл бұрын

both 7440 & 7443 will work for the pilot

Segundo! How's your day buddy?

@Shinegadget

3 жыл бұрын

Good, Thanks bro 👍

@kaalamanHQ

3 жыл бұрын

@@Shinegadget I love your video bud!, Keep it up!. Hope to see more of these :)

Nice job! Big fan I am karen, have you ever heard about my culture??

Those turn leds start to hyper flash because they have been blinking for a while, they will hyper flash to start to cool down or just turn off for them to cool down

@gaelquinones3542

3 жыл бұрын

the company LASFIT mentioned me that when i got mine in

@handon11

3 жыл бұрын

Do you know if resistors will prevent this from happening? I've read about that with the bulbs that have resistors built into the bulbs but curious if adding external load resistors would help with the hyperflashing.

@gaelquinones3542

3 жыл бұрын

@@handon11 I think so but i mean i don’t use my turn signals a lot only when changing lanes and quick turns but they should work with resistors

@handon11

3 жыл бұрын

@@gaelquinones3542 thanks for the reply. I've got a first gen Porsche Cayenne and the front turn signals have a pretty small space so I had to go with a different bulb that is physically smaller than Lasfit and they're supposed to be non-hyper-flashing but we'll see.

@bananameowmeow9260

2 жыл бұрын

@@gaelquinones3542 When use with resistors,does it reduce the max brightness of the turn signals?

Damn I wish I would’ve watched this video before purchasing them for front and back 😅

@Shinegadget

8 ай бұрын

It is ok if you put front and back LEDs for the turn signals with these bulbs, the only thing is that hyper flashes after 3 minutes, if you leave then turned on for more than 3 minutes 👍

@Twisty805

8 ай бұрын

@@Shinegadget ok ok got it, so as long as I don’t leave em o. For longer than 3 or so minuets it should be fine 😅👍🏽

@memopadilla5931

3 күн бұрын

@@Twisty805 did that work for yours ?

I put 2 7440 and it don't hipper flash chech the 7443

@Shinegadget

2 жыл бұрын

Ok thanks 👍

how it is working after two years?

@Shinegadget

Жыл бұрын

still good 👍

GO ASTROSSSSS...

@Shinegadget

2 жыл бұрын

😁👍

Pro Tip : Red lens? Use red bulbs

i just wish every turn signal was like that

@Shinegadget

Жыл бұрын

Yes me too 👍

7443A is just switch backs

Primero!

@Shinegadget

3 жыл бұрын

Gracias 👍

@vincentwalters2091

3 жыл бұрын

Shine Graffix You make fantastic videos and you demonstrate things clearly and carefully so that anyone can understand. Thank you 😊

Amazing that in 2021 it's not a simple plugnplay. You have to use a load resistor to stop the hyperflash.

@exoticcar5482

3 жыл бұрын

Couldn't agree more. I'm just flabbergasted that amber LED isn't included standard universally on all 2021 car models from the factory both front and rear. It is not that expensive to stop using halogen turn signals yet they're an odd holdout

@ilbftman

3 жыл бұрын

@@exoticcar5482 They probably have millions in inventory that they will Not discard. Use up all the old stock first then introduce "New Led lights now standard...."

@gravemind6536

2 жыл бұрын

@@ilbftman Yeah its currently reserved for premium german cars at the moment not made it into everyday cars yet. I don't expect it'll happen too quick either since LED headlights are only on premium cars or high spec cars. Also get lots of people crying that LED and Xenon headlights are blinding too but they are much better for other road users than the halogen reflector headlights seen on most older cars.

@toyotabrony

Жыл бұрын

Ur wrong. When they have a built-in resistor, it’s not truly necessary to have another resistor. If it’s already built into it. Ur set. When u had them on for around 3 minutes. Heat builts up and gets hot. And then hyperflash starts. Turn them off for 2 minutes, and it cools down. That’s all u gotta do.

@toyotabrony

Жыл бұрын

@@exoticcar5482 nope. It’s how they made. When it gets hot, hyperflash. Turn them off, and flash back to normal after 2 minutes.

2 pair of 7440 won't hyper flash

@Shinegadget

2 жыл бұрын

Cool 👍

@memopadilla5931

3 күн бұрын

@tavarasl 7440 work for you both front back at same time no hyperflash ?

You can buy resistors so it won’t hyper flash

@exoticcar5482

3 жыл бұрын

But that defeats the purpose of installing the LEDs to begin with

@rastaman7523

2 жыл бұрын

@@exoticcar5482 wut

@exoticcar5482

2 жыл бұрын

@@rastaman7523 What I mean is most of the time you install LEDs it's to save energy and have better performing light sources, but the resistor basically just increases power consumption back to what the original bulbs had just to trick the BCM into thinking the proper bulb is in place

@toyotabrony

Жыл бұрын

No u don’t. Theee are built/in resistors. Not necessarily to add another resistor. These are plug and play

These get extremely hot I do not recommend them I believe they could be a fire hazard. The resistors are built right in the bulbs that’s why they get hot and it will eventually start a hyper flashing.

@toyotabrony

Жыл бұрын

It’s highly recommended. U be fine with it. If it starts to get hyperflash, that’s pretty normal. When they get hyperflash, that means the heat starts to built up if u have them on for around or more than 2-4 minutes. If they do get hyperflash, turn them off between 1-2 minutes to cool them off. After that, they are back to normal. Nothing wrong with them, and they are very well made led bulbs. Highly recommend them. Lol no they don’t have fire hazard and stuff. That’s what the top of the thicc head of the polish stainless steel with a gold crown on it, which is a heat dissipation.

Not good ., To Bright . I stick to OEM design...

Damn that’s ain’t right too bright he ha ho

@toyotabrony

Жыл бұрын

Lol nah. That’s a great super bright

They look like Chinese made crappy bulbs

who cares if it hyper flash i have it like that and i have led lights every where on back and front

@TonyhatesLego11031people

3 жыл бұрын

Hyper flash is a cop magnet. It’s illegal in most states to

@mrfuel1866

2 жыл бұрын

🤣🤣🤣🤣🤣🤣

@toyotabrony

Жыл бұрын

@@TonyhatesLego11031people but if it’s better improvement, who cares lol