Stuck Wiper Arm - Easy Removal Method
Автокөліктер мен көлік құралдары
Having trouble removing a stuck or seized front windscreen wiper arm ?. Here’s a simple way to remove it using just a locking pliers. Using this method you don’t need to risk damaging the linkage by levering up the spindle and hammering at the thread like with some other methods. This method should work on most front wiper arms, but not all of them. Be careful not to use the glass for leverage as this could put pressure on the glass and break it, especially on rear wipers. Thanks for watching. Please comment, like and subscribe.
~~~~ Part Links ~~~~
As an Amazon Associate I earn from qualifying purchases.
🚗 Locking Pliers ~ amzn.to/3Jew3r3
🚗 Socket Set ~ amzn.to/3BmbuHr
Disclaimer: Screwsnutsandbolts is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to www.amazon.com
All of my uploaded material is protected under copyright law. None of my videos may be re-uploaded, reproduced or transmitted, in part or in full, in any form or by any means, without the written permission of the copyright holder.
© / screwsnutsandbolts 2022
Read important information below:
Disclaimer
Due to factors beyond the control of Screwsnutsandbolts, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. Screwsnutsandbolts assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Screwsnutsandbolts recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of Screwsnutsandbolts, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not Screwsnutsandbolts.
Пікірлер: 351
Thanks for watching my video. If you found this or any of my other videos helpful, maybe you could consider supporting my channel by using the ‘♡ Thanks’ button below each of my videos. Your support would be greatly appreciated, thank you ! 👍 Screwsnutsandbolts
Thank you, thank you, thank you. Didn’t find this video until after I had purchased a gear puller to remove the arm. Couldn’t get it to center, and remove the arm. Back to YT to find your video. One minute later, RESULTS! Sending back the puller today. Many thanks for the quick, cheap, effective tip!
@screwsnutsandbolts
10 күн бұрын
You're very welcome, thanks for watching !
Saved me $25 for a tool I would only have to use once! Tricks like these are rare gems. Thank you.
@screwsnutsandbolts
2 жыл бұрын
You're very welcome !
@josaphatawuzie7617
8 ай бұрын
9
@JudoKnowles
5 ай бұрын
I didn't see this video, looks better than the flat wrench method I was attempting lol. I busted my damn lip and got the puller for $27.
Clearly understood exactly what I needed to do without having to mention a word. Thank you!
@screwsnutsandbolts
Жыл бұрын
You're very welcome, thanks for watching !
I was having this problem working on my C5 Corvette and you saved me from having to buy yet one more tool that I probably would only use just once. Thanks so much.
@screwsnutsandbolts
3 жыл бұрын
You're welcome. I already bought that tool lol :)
Amazing! Thanks a ton for this tip, worked a charm to free up a stubborn wiper arm here in the Rust Belt that resisted my best attempts to free it using penetrating oil, repeated wriggling, and even a rubber mallet. This video is truly KZread at its best!
@screwsnutsandbolts
4 ай бұрын
You're very welcome, thanks for watching !
I’m returning here to thank you. Your method 1 & 2 worked great for my dodge grand caravan.
@screwsnutsandbolts
6 ай бұрын
You're welcome !
Great tip, saved me 20$ and the time to go and get a tool. Thanks
@screwsnutsandbolts
21 күн бұрын
You're welcome, thanks for watching !
I'm a windscreen tech. I'm going to try this because some cars don't have enough room for a wiper puller.
This is BY FAR the best and safest method next to using a 2 jaw puller!!! Your are fantastic!!!
@screwsnutsandbolts
3 жыл бұрын
Thank you very much ! :)
Holy shit man you are my new best friend. Method 2 was the one that worked for me. I wish I found this video earlier would have saved me a windshield. I even bought a special tool to do the job and I didn't work either. Thanks for the video. Now to you the windshield place at the tune of $500.
@1188clean
3 жыл бұрын
damn i feel you. im about to be out a few hundred in the next week. i just broke my wife's windshield trying to take that arm off.
Congratulations and thank you for making a truly helpful instructional video. It's the best I have seen in a while. You performed the actions slow and showed the tools with enough time to actually see them. I give you two thumbs-up and 5 stars for an excellent video. Great job!
@screwsnutsandbolts
2 жыл бұрын
Thank you very much ! :)
I tried the vice grip before watching this video but your tip to leave the nut on is what i was looking for, thanks alot
@screwsnutsandbolts
3 жыл бұрын
You're welcome, thanks for watching :)
spent over an hour trying to remove my wiper arm today , come on youtube and bingo , i will be trying this in the morning , i'm having one of those "why didnt i think of this" moments haha
@screwsnutsandbolts
2 жыл бұрын
lol :). I hope it works for you !
@DavidCulshawmer-r
2 жыл бұрын
@@screwsnutsandbolts it did . 2 mins it took 😄
@screwsnutsandbolts
2 жыл бұрын
@@DavidCulshawmer-r Excellent 😄
Winner!!! Spent ages just looking and scratching my head, pondering how, and in seconds I've done it, thanks mate.
@screwsnutsandbolts
Жыл бұрын
You're very welcome ! 👍
Thank you so much for this. I bought a wiper puller tool and it just bent. Your trick is amazing. I thought I was screwed until I came across your video. You rock!!! Thanks
@screwsnutsandbolts
5 ай бұрын
You're very welcome, thanks for watching !
Still helping people, thank you for sharing this trick! Helped me remove the stuck wipers in 30 seconds , and without risking damaging them, works like a beauty!
@screwsnutsandbolts
Жыл бұрын
You're very welcome, thanks for watching ! 👍
Worked like MAGIC! THANK YOU!!! I’d been fumbling with this thing all DAY! Thank you SO much!!
@screwsnutsandbolts
7 ай бұрын
You're very welcome, thanks for watching !
Think you so much! Would never have gotten the arm off without this video. The wiper motor was going, and if I moved one arm the other moved too. The linkage from the motor the the rest of the arm linkage had popped off. Lubed it up and popped it back on (rust and debris had probably caused it to fall off initially). Anyway, thank you, hope this helps others too
@screwsnutsandbolts
Жыл бұрын
You're very welcome ! 👍
Thanks mate, I'd been struggling with my rear wiper arm for a couple of days on and off. This method got it in one.
@screwsnutsandbolts
3 жыл бұрын
You're very welcome, thanks for watching !
The "special tool" arrived for this job a few days ago as demonstrated in your previous video ! Well worth the tenner and no skinned knuckles .But this method you show is very clever.
@screwsnutsandbolts
3 жыл бұрын
Thanks very much. I just got the idea when looking at what the special tool does. I hope we didn't waste a tenner each lol. I'm still glad to have the other tool, it does the job perfectly and I suspect I might end up using it for some other jobs too :)
I was having issues breaking the arm free, I tried the pulley method and a couple others. None of them worked, but your method broke it free. Thanks so very much.
@screwsnutsandbolts
2 жыл бұрын
You're very welcome !
I did not expect this to work so well, but the arm came right off. Great video
@screwsnutsandbolts
2 жыл бұрын
Thanks for watching ! 👍
Great tip, I had this problem on the rear wiper arm of my vw touran and it worked a treat. Thank you
@screwsnutsandbolts
3 жыл бұрын
You're welcome, thanks for watching ! :)
Great tip cheers from Atlantic Canada👍🏼😎🇨🇦
@screwsnutsandbolts
11 күн бұрын
You're very welcome, thanks for watching !
Great trick, worked like a charm (I was working on my Volvo and thought, "oh great, don't tell me I need a 'special tool' for a simple wiper arm?". Turns out, ya don't . Thank you so much.
@screwsnutsandbolts
10 ай бұрын
You're very welcome !
Thanks!! I went through a "soft touch" car wash and the soft touch brushes broke the plastic piece on that rear wiper arm that holds the blade in. I took the nut off and tried everything except a puller to get that arm off but no luck. I saw your video and tried the vise grip method and it broke free immediately!! Whew!! Thanks again. It worked great.
@screwsnutsandbolts
2 жыл бұрын
You're very welcome, glad it helped :)
Very helpful advice & amusing video. Hope you never scuffed your hands doing that job as it's advisable to wear protection.
Awesome tip - I used channel locks instead of locking plier because it's all I had available, took some pressing but worked all the same! Thanks!!
@screwsnutsandbolts
Жыл бұрын
You're very welcome, thanks for watching !
Hahahahahahah. I was struggling and have no especial tool …. And this helped extremely well…. And i laughed so hard. Thanks.
@screwsnutsandbolts
2 жыл бұрын
You're welcome !
On my two Dodge Rams, 2003 & 2004, there is a simple lever you pull out to release the wiper arm. No nuts or special tools required. However, your video was extremely helpful in working on my Girlfriends Ford Freestar van. Thank you. Funny thing was the nuts on her wipers were two different sizes, 15 and 17mm. What the heck?
@screwsnutsandbolts
3 жыл бұрын
That's strange !. I'm glad it helped :)
Just tried this on my Suzuki Alto, the wiper was off in 30 seconds, thanks so much for this hack!
@screwsnutsandbolts
Жыл бұрын
You're very welcome, thanks for watching !
A job that I'd spent 2 hours on with increasing frustration, finished in under 30 seconds. Worked in the time it took me to say 'yes this isn't going to wor...' oh it has...
@screwsnutsandbolts
Жыл бұрын
Thanks for watching !
Thanks for the tip, worked a treat when nothing else would budge it. Pity I hadn't seen it first before ordering a tool over the internet.
@screwsnutsandbolts
3 жыл бұрын
Thanks for watching, glad it helped :)
I was almost 2 hours trying to remove the rear wiper from my Audi A3 from 2006, by putting tons of penetrating oil and wd40. Found your video and in 5 min I removed it. Thank you.
@screwsnutsandbolts
2 жыл бұрын
You're very welcome !. Thanks for watching :)
Thank you thank you thank you I would not have been able to change my rear windshield wiper without the help of your video. You rock! 😎🤩
@screwsnutsandbolts
Жыл бұрын
Thanks very much, glad it helped ! 👍
That’s a solid tip. Worked a treat. Double thumbs up 👍 👍
@screwsnutsandbolts
2 жыл бұрын
Thanks very much ! :)
I tried everything and this is the ONLY thing that worked. Thank you thank you
@screwsnutsandbolts
3 жыл бұрын
You're very welcome ! :)
Thanks for that. following your video, have just used mole grips and a one pence piece to get my wipers off. What took most of the time was putting the plastic trim back on at the bottom of my windscreen after cleaning underneath it. There's a knack to that too.
@screwsnutsandbolts
3 жыл бұрын
Yeah that can be a bit fiddly alright. Thanks for watching ! :)
Off course this is very much helpful.. You are my hero for helping me do a once in a lifetime job
@screwsnutsandbolts
Жыл бұрын
Thank you ! 😃
Excellent, worked easily after a pry bar was to no avail despite having sprayed Free All on it first. Then put on a generous coating of anti-seize before putting it back together so it will be easier if I need to do it again. But one thing, you could have used a cheaper coin, those might be valuable.
@screwsnutsandbolts
2 жыл бұрын
LOL thanks, I'll use a copper coin next time :)
This method was sooo easy! Mine wasn't quite as stuck as yours but it worked just as well. Thanks!
@screwsnutsandbolts
5 ай бұрын
You're very welcome :)
*Is incredible how people can help a lot without be in direct contact, thank you very much for your video I was struggling a bit and after seeing your video I finish in 2 minutes you save my day, I really appreciate your work*
@screwsnutsandbolts
Жыл бұрын
You're very welcome, thanks for watching !
Thanks mate for the tips without having to invest for specialized tool. It worked fine.
@screwsnutsandbolts
3 жыл бұрын
You're welcome :)
Confirmed. Worked for removing a stubborn rear wiper arm from a 2010 Highlander. Thanks!
@screwsnutsandbolts
Ай бұрын
You're welcome !
@easypeasytrading
Ай бұрын
This video is worth millions,
Thank you! I couldn't get a vice-grip in there, put used channel-locks in the same way and it did the trick! Thank you so much for the idea.
@screwsnutsandbolts
Жыл бұрын
You're very welcome !
You are the guy of guys! Thanks for sharing your cleverness!
@screwsnutsandbolts
2 жыл бұрын
Thanks for watching ! 👍
thank you so much, this worked so well for me. I went and bought a battery terminal pulller because someone in an forum said that works, it was too flimsy/had soft metal and broke. I used your method and got them off in 5 minutes
@screwsnutsandbolts
Жыл бұрын
You're very welcome, thanks for watching !
Have nissan qashqai 2011, wipers well stuck on and corroded, this worked a treat!! thankyou
@screwsnutsandbolts
2 жыл бұрын
You're welcome, thanks for watching !
Worked like a charm with the coin, really appreciated this tip, thanks!
@screwsnutsandbolts
3 жыл бұрын
You're very welcome. Thanks for watching ! 👍
Thank you so much! Worked like a charm on my rear wiper arm!
@screwsnutsandbolts
Жыл бұрын
You're welcome, thanks for watching !
Smart ideas and excellent methods of taking the video. Thank you.
@screwsnutsandbolts
7 ай бұрын
You're welcome, thanks for watching !
Yep worked 1st time, a good tip, cheers.
@screwsnutsandbolts
2 ай бұрын
You're welcome, thanks for watching !
Took a bit of trying and snapping the bottom part but got it off in the end, saved me money at the end of the day
Absolutely WORKED PERFECTLY ! THANKS
@screwsnutsandbolts
2 жыл бұрын
You're very welcome, thanks for watching !
Looked at picture and immediately went to try it, worked same time.
@screwsnutsandbolts
Жыл бұрын
Thanks for watching ! 👍
This works like a charm!! Thanks!! Broke one before knowing you can do this!!
@screwsnutsandbolts
Жыл бұрын
You're welcome !
So obvious, so why didn't I think of it! Saved me from having to buy a puller, excellent solution. Thank you
@screwsnutsandbolts
Жыл бұрын
You're very welcome, thanks for watching
Changed my Estate rear wiper 5yrs ago with no problem, this time the arm is stuck on the spindle solid, so will try your method tomorrow. Hope I don't shatter the rear window, hugh!
@screwsnutsandbolts
2 ай бұрын
Don't use any part of the glass for leverage !
@screwsnutsandbolts
2 ай бұрын
If that doesn't work, I'd recommend trying a ball joint separator like this one: kzread.info/dash/bejne/jJaq09ChorO0mNI.html
Great trick, worked like a charm, thank you.
@screwsnutsandbolts
3 жыл бұрын
You're welcome. Thanks for watching ! :)
Best tip!!! I was trying to remove my arms from a 2002 Sequoia and there is very little clearance around the arm to get underneath the arm with a wiper removal tool. Saw your video and the only change I made was using a pair of needle nose vice grips which barely fit to pop the arm since I have such small clearances. Thanks!!!
@screwsnutsandbolts
3 жыл бұрын
Thanks for watching ! :)
Go to 2010 Mini Cooper S work perfectly thank you
WORKED PERFECTLY!!! Thanks!
@screwsnutsandbolts
Жыл бұрын
You're very welcome, thanks for watching !
Impressive, worked like a treat!
@screwsnutsandbolts
Жыл бұрын
Thanks for watching !
you a real one. thank you this helped so much for my 05 Lincoln ls v6
@screwsnutsandbolts
2 жыл бұрын
You're welcome, thanks for watching !
Thanks brother! You’re a class act.
@screwsnutsandbolts
Жыл бұрын
Thanks for watching !
Awesome! You are a lifesaver!!!
@screwsnutsandbolts
Жыл бұрын
Thanks for watching !
If i could give you 1000 likes! It worked! Thank you! You saved my day!
@screwsnutsandbolts
Жыл бұрын
You're very welcome, glad it helped :)
Great idea. Thanks for posting.
@screwsnutsandbolts
Жыл бұрын
You're welcome, thanks for watching !
Good idea. I'll try that! Thanks for sharing.
@screwsnutsandbolts
11 ай бұрын
Thanks for watching !
You are an absolute legend! Thanks
@screwsnutsandbolts
2 жыл бұрын
Thanks for watching ! :)
You saved my life man thanks. Ie wasn't easy but it did come loose.
@screwsnutsandbolts
Жыл бұрын
You're welcome, thanks for watching !
Thanks for the idea! Worked on my Mk6 GTI after soaking with penetrant on the tapered splines of the shaft.
@screwsnutsandbolts
Жыл бұрын
You're welcome, thanks for watching !
Absolutely fantastic I need to take my daughter's one off and couldn't do it will give this a try
@screwsnutsandbolts
Жыл бұрын
Thanks, good luck 👍
Thank you. Worked a treat.
@screwsnutsandbolts
Жыл бұрын
You're very welcome !
Excellent vids mate and no silly music too. Wonderful info', cheers.
@screwsnutsandbolts
2 жыл бұрын
Thanks very much !
I don't know why I came here and I don't have a stuck wiper, but this vid is awesome.
@screwsnutsandbolts
Ай бұрын
Thanks !
Thank you! This video saved me from having to buy a wiper arm puller.
@screwsnutsandbolts
2 жыл бұрын
You're welcome, thanks for watching :)
Worked a treat! Many thanks 😎🤟
@screwsnutsandbolts
9 ай бұрын
You're very welcome, thanks for watching ! 👍
Bravo, hvala! Pozdrav iz SRBIJE!
@screwsnutsandbolts
Жыл бұрын
You're welcome. Thanks for watching !
Worked like a charm - Thank you Thank you!!
@screwsnutsandbolts
2 жыл бұрын
You're very welcome !
Your a life saver man! I was fighting with the arm for an hour and as soon as I saw the video I was able to pop it right off
@screwsnutsandbolts
Жыл бұрын
You're very welcome !. Thanks for watching !
@Andy-wx4wx
Жыл бұрын
Same here, so simple and yet so effective!
@screwsnutsandbolts
11 ай бұрын
@shawnstafford7809 Sometimes the nuts are covered with a plastic cap. What vehicle do you have ?
@screwsnutsandbolts
11 ай бұрын
@shawnstafford7809 Wow nice car, lucky you ! 😎. I've rarely seen, let alone worked on a Firebird so I have no idea I'm afraid. I've only ever seen wiper arms fitted onto splined shafts and secured with nuts
@screwsnutsandbolts
11 ай бұрын
@shawnstafford7809 Do the arms look like the ones in this video ?: kzread.info/dash/bejne/jJebldmOaMfVo9o.html
Used your video today..... thanks!
@screwsnutsandbolts
3 жыл бұрын
You're very welcome :)
Oh yeah. I slayer it! Thanks
Thanks so much, worked perfectly!
@screwsnutsandbolts
7 ай бұрын
You're welcome, thanks for watching !
Good job! Thumed up, added to the playlist.
@screwsnutsandbolts
3 жыл бұрын
Much appreciated!
@luigi7130
3 жыл бұрын
@@screwsnutsandbolts have a nice holiday Sir ;)
@screwsnutsandbolts
3 жыл бұрын
@@luigi7130 You too ! :)
This is a badass video¡ Thank you very much for the info buddy¡ Greetings from Mexico¡ Keep up the good work¡
@screwsnutsandbolts
Жыл бұрын
You're welcome, thanks for watching !
brilliant, couldn't get them with a puller, but this worked in 30 sec.
@screwsnutsandbolts
Жыл бұрын
Thanks for watching ! 👍
Thanks, worked like a charm.
@screwsnutsandbolts
3 ай бұрын
You're welcome !
@fordjustice1952
3 ай бұрын
I was having my windshield replaced, they were unable to remove the wiper arms and were therefore unable to replace the windshield. I attempted several other techniques shown on KZread to no avail. I will share your video with the windshield installer when I go back this week. This undoubtedly saved me significant time and money. Thanks again.
pure brilliance thank you
@screwsnutsandbolts
Жыл бұрын
Thanks for watching ! 👍
Thank you! The first half of method 1 did the trick. The arm popped off as soon as I was able to clamp the vice grip.
@screwsnutsandbolts
2 жыл бұрын
You're welcome, glad it helped ! 👍
this might work really well in your situation. unfortunately i couldn't fit the pliers on my wipers so i used some gun oil and a hammer and gave them a good tap and they came off very easily i just loosened the nut like you did applied some oil to the base of the bolt and it worked like a charm
@screwsnutsandbolts
2 жыл бұрын
Good job 👍
Thank you for your valuable video! Much appreciated! 🙏🏼
@screwsnutsandbolts
Жыл бұрын
You're very welcome !
Genius, that worked out very well thanks for the tip
@screwsnutsandbolts
2 жыл бұрын
You're welcome, thanks for watching !
Outstanding! Thank you
@screwsnutsandbolts
Жыл бұрын
You're welcome, thanks for watching !
Man this is awesome! Thank you!
@screwsnutsandbolts
Ай бұрын
You're welcome, thanks for watching !
What a great tip 👏
@screwsnutsandbolts
Жыл бұрын
Thank you !
Nice job. Should make life easier for me changing the wiper motor on our Duster.
@screwsnutsandbolts
8 ай бұрын
You're welcome, just be careful not to use the glass for any leverage or it could crack.
Worked for me. TYSM!
@screwsnutsandbolts
Жыл бұрын
You're welcome !
many of us has this tool but don't know how or where to use it , thanks .
@screwsnutsandbolts
7 ай бұрын
You're welcome !