I have had my saw since 1998. It has only required routine maintenance until today when my bearing failed. New parts from E bay on the way. I did not know the threads were left handed on the crankshaft. Loved the way you used something up against the piston to break the inner clutch loose. Thanks for assisting others with your knowledge. I'm off to the shop . God bless .
@4MRanch
2 ай бұрын
Thanks for watching. Good luck on your saw hope you get it fixed.
@personwhoexists4491 Жыл бұрын
Just what I needed. Picked up a 261 for cheap that's missing these parts.
@joankteien85843 жыл бұрын
Great job 4M Ranch! This was exactly what I have been try to solve. Thank you very much!
@4MRanch
3 жыл бұрын
Your welcome glad it helped
@danielpadgett28312 жыл бұрын
I would've clean it up before putting it back together but that's just me
@edoreilly9576 Жыл бұрын
Great video, thanks very much. Very very clear.
@4MRanch
Жыл бұрын
Thank you!
@kawachopa7024 Жыл бұрын
Thank You! :)
@tomcaldon-tf9mw Жыл бұрын
Thanks trying to get to my oiler thanks for the help
@4MRanch
Жыл бұрын
No problem
@swordfish11202 жыл бұрын
Do you recall if the clutch cover was incredibly hot after this happened? I'm trying to diagnose why the clutch cover on my 026 gets so hot. I'm new to this saw so I don't know if this high heat on the clutch cover in normal.
@martingowan7800 Жыл бұрын
When putting sprocket back on you never seen to line up for the oiler?
@joediffie7314 Жыл бұрын
Why did you have to pull the plug and do the rope trick for?
@4MRanch
Жыл бұрын
To remove and tighten the fly wheel nut. It locks the piston from spinning without damage.
@joediffie7314
Жыл бұрын
@@4MRanch ok thanks
@nlowry85 жыл бұрын
Does STIHL still make this chainsaw? I can’t find it anywhere
@4MRanch
5 жыл бұрын
They don’t make it anymore it’s like an 05 model. It’s been replaced by the ms 261-C
@4MRanch
5 жыл бұрын
Yeah it was a good saw. However the new 261 I replaced it with is working really well. It has more power it seems like. I’m impressed
@nlowry8
5 жыл бұрын
I know a guy who has a 261. I might give his a try. Also, great video. It’s very helpful
@4MRanch
5 жыл бұрын
Nic Lowry Thanks man. Yeah I’d say try it I really like mine.
@kickingber
5 жыл бұрын
I don't think they do. I bought 1 new in 2004, have ran the heck out of it ever since with no trouble. wish they still made it.
@jeffw76443 жыл бұрын
If you grease that needle bearing that won’t happen, again, just sayin!
@4MRanch
3 жыл бұрын
Yeah, I keep them greased now and Haven’t had any problems.
@dirksandry65464 жыл бұрын
didn't line up the oil pump worm drive.
@4MRanch
4 жыл бұрын
I never removed the worm drive oil pump and it pumps bar oil just fine.
Пікірлер: 30
I have had my saw since 1998. It has only required routine maintenance until today when my bearing failed. New parts from E bay on the way. I did not know the threads were left handed on the crankshaft. Loved the way you used something up against the piston to break the inner clutch loose. Thanks for assisting others with your knowledge. I'm off to the shop . God bless .
@4MRanch
2 ай бұрын
Thanks for watching. Good luck on your saw hope you get it fixed.
Just what I needed. Picked up a 261 for cheap that's missing these parts.
Great job 4M Ranch! This was exactly what I have been try to solve. Thank you very much!
@4MRanch
3 жыл бұрын
Your welcome glad it helped
I would've clean it up before putting it back together but that's just me
Great video, thanks very much. Very very clear.
@4MRanch
Жыл бұрын
Thank you!
Thank You! :)
Thanks trying to get to my oiler thanks for the help
@4MRanch
Жыл бұрын
No problem
Do you recall if the clutch cover was incredibly hot after this happened? I'm trying to diagnose why the clutch cover on my 026 gets so hot. I'm new to this saw so I don't know if this high heat on the clutch cover in normal.
When putting sprocket back on you never seen to line up for the oiler?
Why did you have to pull the plug and do the rope trick for?
@4MRanch
Жыл бұрын
To remove and tighten the fly wheel nut. It locks the piston from spinning without damage.
@joediffie7314
Жыл бұрын
@@4MRanch ok thanks
Does STIHL still make this chainsaw? I can’t find it anywhere
@4MRanch
5 жыл бұрын
They don’t make it anymore it’s like an 05 model. It’s been replaced by the ms 261-C
@4MRanch
5 жыл бұрын
Yeah it was a good saw. However the new 261 I replaced it with is working really well. It has more power it seems like. I’m impressed
@nlowry8
5 жыл бұрын
I know a guy who has a 261. I might give his a try. Also, great video. It’s very helpful
@4MRanch
5 жыл бұрын
Nic Lowry Thanks man. Yeah I’d say try it I really like mine.
@kickingber
5 жыл бұрын
I don't think they do. I bought 1 new in 2004, have ran the heck out of it ever since with no trouble. wish they still made it.
If you grease that needle bearing that won’t happen, again, just sayin!
@4MRanch
3 жыл бұрын
Yeah, I keep them greased now and Haven’t had any problems.
didn't line up the oil pump worm drive.
@4MRanch
4 жыл бұрын
I never removed the worm drive oil pump and it pumps bar oil just fine.