This is by far the best method for gaining full adjustability on those carbs. Thanks for the stellar video
@mooregoodink773412 күн бұрын
Brennan, Thank you for this valuable information. Your kindness is much appreciated. I aligned each little groove with its corresponding limiting ball as you suggested, marked the center of each ball with an automatic center punch and using a 3/32in drill bit carefully drilled them out. It's difficult to see how the manufacturer gained an advantage by altering the carburetor in this way as the internals were caked with dirt.
@richardflagg3084 Жыл бұрын
Great explanation. Honestly I never realized there was a 2mm allen head in there. I've always drilled them out. Yes, those pins are hardened, and occasionally the bit will drift. Going forward I'll be doing it your way. Much cleaner. Thanks Brennan.
@j.chrisbeck7492 Жыл бұрын
Thank you for that information, it may come in handy, I have the MS271, but I have not found the need to make any adjustments beyond the limits
@jerseyjoshua4818 Жыл бұрын
A wise man, giving away free knowledge.... is a good man! Just my worthless 2¢
@tazman-kennyfuller5 ай бұрын
Thank you Brennan. You rock. 🌲❤️🌲👊🪓
@chrisbiltoc4567 ай бұрын
This is the best way to do it. TY
@stevemcdowell20195 ай бұрын
Again Brennan, you the man!
@jjm3254 Жыл бұрын
Great tip. Thanks.
@G-PA-279510 ай бұрын
Good info Brennan
@TheKppus8 ай бұрын
Tnx man !
@ClintsHobbiesDIY Жыл бұрын
Good to know even though I don't have any of those models.
@Super-Dave-Outdoors Жыл бұрын
I ground a slot through the pin with zip wheel on the one i did. Didnt know about the allen trick.
@justinweaver8107 Жыл бұрын
That is ridiculous how they made those so hard to adjust.
@jonathanglanville79539 ай бұрын
When I tried to back out the adjuster like you showed, it ended up breaking the plastic piece that you showed in the beginning of the video. Any tips?
@larchman43275 ай бұрын
Got your saw to start smoking. My plug too clean worries me.
@toddjacobs56606 ай бұрын
I just drilled my ms271 carb plugs out today with a 5/32" bit, it drills easy its just aluminum, i adjusted it better than when i bought it new, my low idle was too lean ...
Пікірлер: 17
This is by far the best method for gaining full adjustability on those carbs. Thanks for the stellar video
Brennan, Thank you for this valuable information. Your kindness is much appreciated. I aligned each little groove with its corresponding limiting ball as you suggested, marked the center of each ball with an automatic center punch and using a 3/32in drill bit carefully drilled them out. It's difficult to see how the manufacturer gained an advantage by altering the carburetor in this way as the internals were caked with dirt.
Great explanation. Honestly I never realized there was a 2mm allen head in there. I've always drilled them out. Yes, those pins are hardened, and occasionally the bit will drift. Going forward I'll be doing it your way. Much cleaner. Thanks Brennan.
Thank you for that information, it may come in handy, I have the MS271, but I have not found the need to make any adjustments beyond the limits
A wise man, giving away free knowledge.... is a good man! Just my worthless 2¢
Thank you Brennan. You rock. 🌲❤️🌲👊🪓
This is the best way to do it. TY
Again Brennan, you the man!
Great tip. Thanks.
Good info Brennan
Tnx man !
Good to know even though I don't have any of those models.
I ground a slot through the pin with zip wheel on the one i did. Didnt know about the allen trick.
That is ridiculous how they made those so hard to adjust.
When I tried to back out the adjuster like you showed, it ended up breaking the plastic piece that you showed in the beginning of the video. Any tips?
Got your saw to start smoking. My plug too clean worries me.
I just drilled my ms271 carb plugs out today with a 5/32" bit, it drills easy its just aluminum, i adjusted it better than when i bought it new, my low idle was too lean ...