you're really very good it's a shame we can't give several thumbs up because you deserve it because people who do demonstrations like you are rare on KZread, well done

@frankslittleworkshop

2 жыл бұрын

😁 Thank you very much Eric. Its nice to be appreciated 😁. Thanks for watching 😁👍

"I needed one of these because I didn't have one." :) Excellent review.

@frankslittleworkshop

3 жыл бұрын

😂🤣 that's the "Frank's Little Workshop" rule. If you haven't got one.. you need it... but if you get it... you must use it 😁. Plus... I just like getting stuff 😂🤣. Thanks for watching 😁👍

@villain1409

3 жыл бұрын

@@frankslittleworkshop I bought this Crap & cannot even open it. No where near worth the bother.

@frankslittleworkshop

3 жыл бұрын

@@villain1409 that's a shame 🤔. If it's faulty you are entitled to a full refund or replacement from where you bought it from. My one is still working fine so I guess you got a duff one. Let me know how you get on sending it back 😁👍

@villain1409

3 жыл бұрын

@@frankslittleworkshop I bought it from a seller on Amazon & got told a pile of nonsense so i put it in the bin.

You are very practical and technical without any unnecessary stories. Thank you very much for the fair review.

@frankslittleworkshop

3 жыл бұрын

Thanks for your comment 😁. I hope you found it useful. and thanks for watching 😁👍

Thanks for sharing this. I was considering it for model engineering, so you've just saved me buying something unsuitable! Appreciated!!

@frankslittleworkshop

3 жыл бұрын

Thanks 😁. Your right, I don't think this is the best type of vice for model engineering. But it's designed more for construction site or bench woodworking. The jaws just wouldn't be good enough. I think you need a more traditional engineers vice. Thanks for watching 😁👍

Helpful review. Thank you very much

@frankslittleworkshop

3 жыл бұрын

😁 You are more than welcome 😁. I am still using it and it is still a very useful addition to the workshop. Thanks for watching 😁👍

Great review. Thank you. 👍

@frankslittleworkshop

3 жыл бұрын

😁 Thanks Daniel 😁. I'm still using it and it's working a treat. Thanks for watching 😁👍

That’s really interesting. Never seen anything like that here in the US before. Thanks for sharing!!

@frankslittleworkshop

4 жыл бұрын

Thanks Sam 😁. I think it is only Stanley that make this type of vice. I wonder if they have some type of copyrite on the design ???. Time will tell if it is any good. Thanks again for watching 😁👍

Great review,Thankyou!

@frankslittleworkshop

2 жыл бұрын

😁 Your more than welcome 😁. Thanks for watching 😁👍

...you're a natural, Frank...brilliant review, no nonsense.

@frankslittleworkshop

2 жыл бұрын

😊 Thank you very much. Very nice of you to say. I'm still using this regularly and it is actually a really handy vice. Thanks very much for watching 😁👍

Great job on the video 👍👍

@frankslittleworkshop

10 ай бұрын

😁 Thanks Dean, glad you liked it 😊. Thanks for watching 😁👍

Which one is useful for heavier jobs st183069 or this one?

GOOD REVIEW, you really covered alot. You got a sub.

@frankslittleworkshop

7 ай бұрын

😁 Thanks Mick, much appreceated. I hope it was of some help. Thanks for watching 😁 👍

Nice review Frank. 👍The jaw misalignment is a bit of a schoolboy error on the part of the manufacturer. 😬

@frankslittleworkshop

4 жыл бұрын

I think it is an added feature created by the "cost saving" department 🤣😂. But it's still a usefully bit of kit. 👍. I never cut wood straight anyway... so it will fit just fine 😂. Thanks for watching 😁👍.

Got one love it . Hard to find though

@frankslittleworkshop

2 жыл бұрын

😁 I must admit, I haven't seen them lately. Glad I've still got my one 😁. I used it today... and still love it. Thanks for watching 😁👍

Cracking video that mate.

@frankslittleworkshop

3 жыл бұрын

Thanks Danny 😁. Glad you liked it. Hope it was of some use. Thanks for watching 😁👍

@dannyfree1120

3 жыл бұрын

@@frankslittleworkshop just bought one. Cheers

Cheers for reviewing. Did you ever get the jaws to align? What material did you use for the shim, if so? Mine just arrived and saw the alignment but don't want to back it if I don't have to.

@Drokkstar_

4 жыл бұрын

Been looking at it and I can't see how to shim it without weakening it. The actual jaw material isn't shaped right and looks like a design flaw. Seems most people have had the same problem. Wish I'd read the reviews more thoroughly before I bought it!

@frankslittleworkshop

4 жыл бұрын

@@Drokkstar_ Hi Toby. I have not shimmed the jaws as I have only used it for holding rough work where the jaw alignment is not critical. For general use like that it is a great bit of kit. For anything more refined I think an engineer's vice is the way to go. It's a shame about the jaws but it's still a very usefully addition to my workbench. Thanks for watching Toby 😁👍

Goody review.

@frankslittleworkshop

4 жыл бұрын

Thanks 😁. I'm sure this could be used for a whole host of "holding stuff" type uses. Thanks again for watching 😁👍.

Looking at one for guitar pickups to hold while soldering and guitar nut while filing and sanding. Any good?

@frankslittleworkshop

2 жыл бұрын

🤔 I love this thing for general workshop tasks. But for any work on pickups I don't think this is the best choice. Sounds like you would be better off with a proper engineering vice. Which would give you more precise holding. Hope that helps. Thanks for watching 😁👍

@yobentley7274

2 жыл бұрын

@@frankslittleworkshop I'll look for one. Thanks

Second vice you showed, do you know how to use it, I think not. So I will tell you. Clamp vice to bench, I think you can do that as I saw you do it. Now have a look at the vice really hard, notice it ha a ball structure half way up, now look at the front halfway up you will see a lever, move lever to unlock ball joint, now you can move jaws into all sorts of positions then you lock the ball with lever. Pattern makers vice.

@frankslittleworkshop

6 ай бұрын

Robin ? I think you completely missed the point. Please re-watch the video. The point i made regarding the second vice was it only has one point of contact with the bench.... not how the vice functions. With a single point of contact with a rubber pad on a wooden bench in a dusty wood working shop.... it will move. Regarding knowing how to use a vice, if I can't use one after using one almost daily for 40 odd years I think I must be an extremely slow learner 🤔. Thanks for watching.

not a bad design actually, a bit poor implementation, thanks for the review!

@frankslittleworkshop

8 ай бұрын

😁 I agree. Its very handy but could be much better 😁. Thanks for watching 😁 👍

Get yourself a vintage Swiss zyliss vice. Better by design

@frankslittleworkshop

Жыл бұрын

😃 Just looked at them 😃. Looks a great tool. If the Stanley fails i may invest in one. Thanks for watching Andrew 😁 👍

I have this....do you think it's strong enough to use for my prop shaft centre bearing replacement job? I need to put the car prop shaft in the vice and hammer the spline apart with force? (or do i need to invest in an old school vice?) kzread.info/dash/bejne/aaB41JJmetuedsY.html

@frankslittleworkshop

3 жыл бұрын

Hi Rob 😁. Thanks for the question. This is not the vice you need for your prop repair ☹. You will need something much more robust for that. Yes an old school cast type engineers vice is what you need, an old Record type vice would be best. Don't get a cheap new one... you will be disappointed, have a look on Ebay for something heavy and old... you will love it. Thanks Rob, let me know how you get on. Thanks for watching 😁👍.

Another piece of stanley junk tool. I would not even buy this for a $1. Come on Stanley, this must of been designed by your black and decker team!

@granmabern5283

2 жыл бұрын

It’s great for wood sculpting.